Range of deck mounted, three-hole, single outlet (fixed) combination tap assemblies (brass body - various finishes). The products incorporate 1/4 turn ceramic disc headworks with single lever, dome type, cubed or cross top operating members. The spout outlets incorporate plastic aerators. The products are supplied with stainless steel braided PEX lined flexible hose assemblies for connection between the side valves and the spout and click type pop-up wastes (verified by test). Maximum working pressure 3.5 Bar. Maximum operating temperature 60.0°C.
Three hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating quarter turn ceramic disc headworks with cross top or lever type operating members. The spout outlets incorporate a plastic aerator. The products are supplied with stainless steel braided PEX lined flexible connecting hose assemblies, for use between side body valves and spout. Maximum working pressure - 10 Bar. Maximum operating temperature - 70°C.
Range of single hole, single outlet (fixed) combination tap assemblies (various finishes - see model). Electronic controls on the left-hand side of the body allow the tap to dispense one or more of the following (model specification dependent): boiling, chilled or sparkling water. Ambient (hot and cold) water is controlled via a ceramic cartridge headwork with a single lever operating member. The spout incorporates a plastic aerator on the Sparkling/Chilled and the Ambient outlet, and a separate outlet for the boiling water. Both model ranges incorporate a vent outlet within the tap spout for the boiling water circuit. Maximum working pressure 5.0 bar (Ambient (hot and cold) circuit only). 95458xxx models - Boiling circuit has a maximum operating temperature of 100°C. All other circuits have a maximum operating temperature of 65°C. 95459xxx models - Boiling circuit has a maximum operating temperature of 100°C. The ambient circuit has a maximum operating temperature of 65°C. The chilled/sparkling circuit has a maximum operating temperature of 60°C.
Range of horizontal and vertical expansion vessels with EPDM membrane and stainless-steel connections. Maximum working pressure: 8.0 bar (35 litre model); 10.0 bar (50 litre up to 400 litre models).
Range of inline filter cartridges with plastic or chromium plated brass bodies. Models 02-803231, 02-803235 & 02-803236 incorporate a plastic flow regulator, stainless steel filter and and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides adequate backflow protection. Model 02-000242 is a replacement filter for 02-803236 Chrome In-line filter. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of M type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of press fittings and pipe. Fittings incorporate EPDM ‘O’-rings Maximum working pressure 10 bar. Maximum operating temperature 95°C
‘SR’ range of capillary solder ring copper fittings for use with copper tube EN1057, for above ground use only. Maximum working pressure: 25.0 bar. Maximum operating temperature: 85°C.
“DZRCOM” range of DZR brass compression fittings for use with copper pipe (manufactured to EN 1057). The tank connectors incorporate a NBR gasket. The straight tap connectors incorporate a blue fibre gasket. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of Redman fittings with mild steel bodies (polyamide coating) for use with Puriton II PE-AL-PE barrier pipe - For above and below ground and cold-water use. Jointing is achieved by hydraulic compression. Maximum working pressures: 12.5 Bar for 63mm SDR 11 PE80 pipe system, 10.0 Bar for 90mm to 180mm SDR 17 PE100 pipe system, 16.0 bar for 90mm to 180mm SDR 11 PE100 pipe system. Cold water use only.
IDC ‘BDGxxx’ range of press fittings with brass or nickel plated brass bodies (see model) incorporating EPDM ‘O’-rings and stainless steel crimp sleeves for use with PEX/AL/PEX multilayer pipe (manufactured to EN ISO 21003). The BDG241 and BDG257 prefix models incorporate an EPDM gasket on the captive nut end connection. Pressfit jointing is achieved by either a U or TH crimping profile. Compression connections are for use with copper pipe 12-28mm (manufactured to EN1057) or Irish copper pipe 14.7-27.4mm (manufactured to EN1057). For above ground use only. Maximum working pressure 10.0 bar. 20, 25 & 26mm pressfit sizes cold water use only. Threaded, compression and 16 & 32mm pressfit sizes maximum operating temperature 95°C. From June 2025: The 20, 25 & 26mm pressfit sizes (TH profile only) maximum operating temperature 95°C.
Range of end feed copper fittings for use with copper tube manufactured to EN1057, for above ground use only. Maximum working pressure 25.0 bar. Maximum operating temperature 85℃.
Range of dual flush syphonic WC flush valves. Cold water use only.
Range of WC dual flush drop valves with plastic bodies and silicone seals. The valves are operated via a two push button assembly for either full or reduced flush and incorporate an internal overflow. Cold water use only.
Ultrims Ultrasonic range of in-line water meters with brass or plastic (-01 suffix models) bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.
Range of stainless steel bodied mechanical pump shaft seals. The 491 model comprises of carbon and silicone carbide seal faces and EPDM ‘O’-rings. The 1510 model comprises of carbon and silicone carbide seal faces, EPDM ‘O’-rings and an orange NBR/aramid fibre gasket. Maximum operating temperature 100°C.
Range of concealed rough-in sets with brass bodies, intended for use in conjunction with trim and finish sets. Maximum working pressure 10.0 Bar Maximum operating temperature 85.0°C
Range of submersible pressure sensors and hydrostatic transmitters (supplied in lengths up to 1000m). Cold water use only.
Range of horizontal self-priming multistage pumps with stainless steel bodies, stainless steel impellers, shaft and outer sleeve. Maximum working pressure 10.0 Bar Maximum operating temperatures: MH Three phase models 85°C, MH Single phase models 55.0°C and EH sp models 35°C.
‘Right Pump’ range of single and twin pumps with plastic bodies. The universal models incorporate a non-return valve on the outlet(s) of the pump body (x2 for the RP50TU model) and an expansion vessel. The twin models incorporate a bypass tube between each side of the pump. The inlet(s) of the pump body incorporate(s) a combined EPDM washer and stainless-steel strainer. The inlet and outlet hoses incorporate an isolation valve on the pushfit connection. The push fit connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 1.5 to 3.6 bar (see model). Maximum operating temperatures 60°C.
Page 193 of 311
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
