Range of handwheel operated bronze bodied stop valves. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of push-fit, screw down stop valves with plastic bodies for use with copper pipe (manufactured to EN1057), PEX pipe (manufactured to BS 7291-3) and/or MDPE pipe (manufactured to EN 12201 (inserts required). For above and below ground use. Maximum working pressure:16.0 bar Maximum operating temperature: 20.0°C.
Range of inline plastic bodied screw down stop valves incorporating a non-rising spindle headwork with a dome type operating member. The products are for use with PE-X pipe (manufactured to BS 7291-3) and copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Cold water use only. From March 2026: Maximum operating temperature 65°C.
Range of inlet control groups with a DZR brass body, consisting of a pressure reducing valve and pressure relief valve set to 6bar. The outlet incorporates a single check valve cartridge verified by test (suitable for backflow protection against Fluid Category 2. Pressure reducing range 1 bar to 6 bar Maximum working pressure 10 Bar Maximum operating temperature 85°C
Range of inlet control valves with DZR brass bodies. The valves consist of an adjustable pressure reducing valve set at 3.0 bar, pressure relief valve set at either 4.5, 6.0 or 8.0 bar. The valves also incorporate an approved check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). For use with copper pipe to BS EN 1057. Maximum working pressure 16.0 Bar. Maximum operating temperature 65°C.
Range of water conditioners with stainless steel bodies. Maximum working pressure 10 Bar. Maximum operating temperature 85°C.
'ZHR‐SRC'. Factory applied, grey coloured Sulphate Resistant cement. Mix cement and sand in a 2:1 mass ratio. Apply as per manufacturer's instruction sheet '2025.8.27'. Steam cure for 8 hours@50°C. For use with water up to 65°C.
'Ecocoat FBE Green Powder PFC/6018 (RAL 6018)& Ecocoat FBE Red Oxide Powder PFC/3000-Red Oxide'. Factory applied, green or red coloured epoxy coatings. Apply as per manufacturer’s Product Data Sheet revised ‘1st Jan, 2024’. Cure for 3 minutes at a metal temperature of 230°C. For use with water up to 85°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘Eurokote® 48-20 Brun Rouge’. Factory applied, red coloured, two-part epoxy coating. Mix resin and hardener in a 2.13:1 mass ratio and apply as manufacturer's TDS dated '10/12/2024'. Cure for 24 hours@20°C. For use with water up to 23°C.
'Epilux 610 T Primer for use with Epilux 155 SF Topcoat'. Factory applied, white coloured (once applied) two-part epoxy coating. The topcoat can also be used alone, without the primer. 'Epilux 610 T Primer’ comprises of a base & hardener to be mixed in a 3:1 volume ratio and then applied as per manufacturer's TDS 'SEPTEMBER 2018 VERSION 1'. Cure for 16 hours@25°C – 28°C, 60%±10% RH. 'Epilux 155 SF Topcoat' comprises of a base & hardener to be mixed in a 4:1 volume ratio and then applied as manufacturer's TDS 'SEPTEMBER 2018 VERSION 1'. Cure for 7 days@25°C – 28°C, 60%±10% RH. For use with water up to 60°C. This material is only approved for the RH, mixing & curing conditions that appear on the approval. If the RH, mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'BSS-P'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's TDS 'BSS-P-D0002' dated '2025-1-10'. Cure for 7 minutes@180°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PMSP5112-M, PMSP5113-M, PMSP5114-M, PMSP5115-M, EP5112D01SC, EP5113D01SC, EP5114D01SC & EP5115D01SC'. Factory applied, blue coloured, Porcelain Vitreous Enamel coatings. Apply as per manufacturer's User Manual 'PEM 37', 'Edition 01', dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NMSP2251M, NMSP2265M, NMSP2266-M, NMSP2267-M, ER2251A01SM, ER2265A01SM, ER2266A01SC, ER2267A01SC'. Factory applied, blue coloured, Porcelain Vitreous Enamel coatings. Apply as per manufacturer's User Manual 'PEM 38', 'Edition 01', dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'L-01 GP Blue-grey Enamel'. Factory applied, blue-grey coloured Enamel coating. Apply as per manufacturer's TDS 'Version: 01', dated '2025-01-02'. Cure for 15 minutes@200°C and then fire for 10 minutes@850°C. For use with water up to 85°C. This material is only approved for the curing/firing conditions that appear on the approval. If the cure/fire conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘BSS R/G System’. Grey coloured, factory applied, two-component epoxy coating comprising of ‘BSS Red and BSS Grey’. ‘BSS Red’ comprises of a base and curing agent which are mixed in a 3:1 volume ratio. ‘BSS Grey’ comprises of a base and curing agent which are mixed in a 3:1 volume ratio. Apply as per manufacturer's Product Data Sheet ‘BSS-D0003’, dated ‘2025-09-16’. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Nitcote CM 210’. Site applied, two-part, grey coloured (once applied), Cementitious Waterproofing coating. Mix ‘CM 210 white’ liquid polymer and ‘CM 210 grey’ powder in a 1:3.6 weight ratio and apply two coats as per manufacturer's TDS 'UAE/0210/23/Z-1'. Cure Coat 1 for 3 hours@35°C and Coat 2 for 21 days@23°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Nitocote EP 405’. Site applied, two-part,white coloured epoxy based Waterproofing coating. Mix 3.1 litres of the base with 0.9 litres of hardener and apply as per manufacturer’s TDS ‘UAE/0228/22/K’. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'REGZ40 & REGZ41'. white coloured (translucent) silicone grease. Apply as per manufacturer's instructions. For use with water up to 65°C.
'Proofex HDPE B125'. White coloured, extruded HDPE waterproofing membrane. For use with water up to 60°C.
'Seal Ring T11/T21'. Grey coloured, extruded PE seal ring. For use with water up to 85°C.
'Innogaz'. Black coloured, injection moulded, HDPE (PE100) electrofusion fittings. For use with water up to 60°C.
'XS10B & XRC30B'. Black coloured, extruded, Polyethylene materials. For use with water up to 23°C.
Grades manufactured in Marietta, Ohio: Radel R-5100 NT 15, R-5000 NT, R-5000 NT ECHO RP, R-5100 NT ECHO RP, & R-5100 NT (natural). Radel R-5100 BU 1197 & R-5100 BU1197 ECHO RP (blue coloured). Grades manufactured in Oudenaarde, Belgium & Marietta, Ohio Radel R-5100 GY 1037, R-5100 GY1037 ECHO RP, R-5100 GY1037LF & R-5100 GY1037 LF ECHO RP (grey coloured). Radel R-5100 BK 937 & R-5100 BK937 ECHO RP (black coloured). Radel R-5500NT & R-5100 NT15 ECHO RP (natural). Radel 5100 BU 1197 ECHO RP (blue coloured). Injection moulded, polyphenylsulfone materials. For use with water up to 85°C.
'Hepworth Qatar PPR 125 Pipe'. Green coloured (opaque), extruded PPR pipe. For use with water up to 85°C.
‘Udel P-3500 NT LCD, GF-110 NT, GF-120 NT, GF-121 NT, P-1700 NT 11 MR, P-1700 NT 11, GF-121 NT ECHO RP & P-3500 NT LCD ECHO RP’ (all beige translucent). ‘Udel P-1700 Grey 8057’ (grey coloured). ‘Udel P-1700 BK 937, P-1700 BK 937 MR, GF-120 BK 937, GF-121 BK 937, GF-121 BK 937 ECHO RP, GF-120 BK 937 ECHO RP & P-1700 BK937 ECHO RP’ (all black coloured). ‘Udel P-1700 WH 7407’ (white coloured). Injection moulded, polysulphone materials. For use with water up to 85°C.
'Polymax E708DW 'O' rings'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 70A. Tested in-radius size 1.85mm. For use with water 85°C.
'HT5697-50'. Black coloured, injection moulded EPDM material. Shore hardness 67 ShA. Tested in-radius size 1.0mm. For use with water up to 60°C.
‘EPDM-W 70817’. Black coloured, compression moulded EPDM rubber material. Shore hardness 80A. Tested in-radius size 0.98mm. For use with water up to 85°C.
'DLYY E6202'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.1mm. For use with water up to 23°C.
'WE-HR-01'. Black coloured, compression moulded EPDM rubber material. Shore hardness 75. Tested in-radius size 0.99mm. For use with water up to 85°C.
'Dutral K-Co-054'. Black coloured, compression moulded EPDM materials. Shore hardness between 52A & 80A. Tested in-radius size 1.0mm. For use with water up to 65°C.
'EP500'. Black coloured, injection moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'KF011670FDA'. Black coloured, compression moulded, FKM rubber material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
Range of injection moulded, VMQ rubber gaskets, seals, & `O` rings manufactured from the below compounds. The components are available in blue, green, grey, opaque (beige coloured), red, transparent & yellow. The numbers in the name of the compound indicates the shore hardness between 40 & 80. Tested in-radii sizes: Gaskets: 0.2mm - 5.0mm. Seals & `O` rings: 0.5mm - 5.0mm. S50B04E, S60B00E, S70B06E, S70B07E, S70V02E, S50V01E, S60O02E, S70O05E, S50O03E, S50O05E, S60O01E, S70O03E, S40A01E, S60A00E, S70A02E, S40R03E, S45R01E, S50R10E, S50R01E, S60R05E, S65R04E, S70R04E, S80R01E, S40R02E, S50R06E, S60R07E, S70R19E, S70R24E, S50T05E, S50T00E, S55T00E, S60T00E, S60T00T, S70T04E, S70T00E, S75T00E, S80T00E, & S70G01E. For use with water up to 85°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated stainless steel bodies). The flow is controlled by a solenoid valve that is activated via an infrared sensor, and the spout outlets incorporate plastic aerators. Maximum working pressure 8.0 Bar Maximum operating temperature 65.0°C
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlets incorporate plastic aerators. Maximum working pressure:8.0 Bar Maximum operating temperature:65 °C
Single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass), flow is controlled by a solenoid valve, activated via an infra-red sensor. The product is supplied with a combined TPE washer and stainless-steel strainer to be installed on the inlet to the solenoid. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass), flow is controlled by a solenoid valve, activated via an infra-red sensor. The product is supplied with a combined TPE washer and stainless-steel strainer to be installed on the inlet to the solenoid. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Range of bottom and side entry BS1212-4 (2016) compact type float operated inlet valves, for WC flushing cisterns with plastic bodies and adjustable floats and a plastic flow regulator at the inlet. Maximum operating pressure: 10 bar. Maximum operating temperature: 23°C.
WC Cistern incorporating a side or bottom entry float operated inlet valve and a Syphon (Phantom S), Pneumatic Drop Valve (Phantom V) or Cable Operated Drop Valve (Phantom T) with full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern can be operated by lever or push button. Maximum working pressure 10.0 bar. Cold water use only.
W/C suite with pan (polyester) and a concealed flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a single flush drop valve for full flush volumes of up to 6 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 Bar. Cold water use only.
Range of spherical valves with DZR brass bodies, chromium plated brass balls, PTFE seats and EPDM rubber ‘O’-ring. The products also incorporate a ‘Y’- Patterned stainless steel strainer. Compression connection to be used with copper EN1057. AI-0396A062815CR incorporates an approved single check valve cartridge, verified by test - suitable for backflow protection against fluid category 2. Maximum working pressure: 25.0 bar. Maximum operating temperature: 100°C (model AI-0396A062815CR 65°).
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated stainless steel or brass bodies, see models). The flow is controlled by a solenoid valve that is activated via an infrared sensor. Temperature is controlled independently via a single lever operating member. The spout outlets incorporate plastic aerators. Supplied with hoses that incorporate stainless steel strainers and an approved single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 Bar Maximum operating temperature 65.0°C
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies). Flow is controlled by solenoid valves activated via an infra-red sensor and the temperature is controlled independently via single lever. The spout outlets incorporate plastic aerators. Maximum working pressure 8 Bar. Maximum operating temperature 65°C.
Range of T type thermostatic mixing valves with chrome plated DZR brass bodies. Compression and push-fit models for use with copper pipe manufactured to EN1057. Models 37.20122.015.CP,37.20122.022.CP, 37.21122.015.CP, 37.21122.022.CP, 37.21222.015.CP, 37.21222.022.CP, 37.20162.015.CP, 37.20162.022.CP have isolation valves and strainers on the inlet. Maximum working pressure 10.0 Bar. Maximum operating temperature 85.0°C.
Spring loaded, resilient trim check valve cartridge with plastic body and EPDM O-rings. For insertion into fittings with specifically sized bores. Maximum working pressure: 16 Bar. Maximum operating temperature: 85°C.
‘TankBoost’ range of cold-water storage cisterns, incorporating a float operated inlet valve. The C5 suffix models incorporate a Type ‘AB’ air gap with a meshed weir overflow (verified by test - suitable for backflow protection against Fluid Category 5). Cisterns with SUB in the model code incorporate a submersible pump and an expansion vessel. All models incorporate a screened warning pipe and dip tube. Models without a C5 suffix also incorporate a screened breather. Maximum working pressure 10.0 bar. Cold water use only.
‘TankBoost 5 bar’ range of cold-water storage cisterns, incorporating a float operated inlet valve. The C5 suffix models incorporate a Type ‘AB’ air gap with a meshed weir overflow (verified by test - suitable for backflow protection against Fluid Category 5). Cisterns with SUB in the model code incorporate a submersible pump and an expansion vessel. All models incorporate a screened warning pipe and dip tube. Models without a C5 suffix also incorporate a screened breather. Maximum working pressure 10.0 bar. Cold water use only.
Single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with cross top operating members. The spout outlet incorporates a plastic aerator and a swivel nozzle. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| D22 | 22 mm | 10 bar | 85 °C | Gear, D22, Production date (DD/MM/YY) | Body | No | |||||
| D15H | 15 mm | 10 bar | 85 °C | Gear | Body | No | |||||
| D15C | 15 mm | 10 bar | 85 °C | Gear | Body | No | |||||
| R19H | 19 mm | 10 bar | 85 °C | Gear, 19H, Production date (DDMMYY) | Body | No | |||||
| R19C | 19 mm | 10 bar | 85 °C | Gear, 19C, Production date (DDMMYY) | Body | No |
Page 183 of 209
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
