Range of copper or brass (see model) end feed fittings for use with copper tube (manufactured to BS EN1057). Tap connectors incorporate Fibre/NBR washers. Male and female union adaptors incorporate a silicone gasket. Maximum working pressure using hard solder: 8mm to 28mm, ½” to 1” BSP (F) or (M), 1” straight cylinder union and captive nut ½” to ¾”: 25.0 bar, 35mm to 54mm, 1¼” to 2” BSP (F) or (M): 16.0 bar. Maximum working pressure using silver brazing alloy EN1044: 66.7mm to 108mm, 2½” to 4” BSP (F) or (M): 16.0 bar, 133mm to 219mm: 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range electric, instantaneous, open outlet, mains water heaters. Maximum working pressure 6.6 bar. Maximum operating temperature 70 ˚C.
Electric instantaneous water heater with a plastic casing. Flow is controlled via a solenoid valve operated by an infrared sensor. Temperature is controlled by a dial on the front of the unit. The product incorporates a swivel arm outlet from the base. Maximum working pressure 3.0 bar. Maximum operating temperature 48˚C. Cold supply only.
Range of under-sink, electrically heated vented water heaters (cased and insulated). Maximum operating temperature 98˚C
Range of heat interface units incorporating a heat exchanger, flow sensor, spherical valve and shock arrestor. The heating circuit incorporates a pressure relief valve set at 3.0 bar. Maximum working pressure & operating temperature: Primary circuit is 16.0 bar & 90°C. Domestic hot water circuit is 10.0 bar & 65°C. Heating circuit is 2.5 bar & 80°C.
Range of water meters with blue epoxy coated cast iron bodies. Maximum working pressure 16.0 Bar Maximum operating temperature 65.0°C
Range of inline water meters with brass bodies (blue or red epoxy coating). The inlet incorporates a plastic strainer. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
Direct coupler (brass with a range of finishes). Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of Fastec® F13 and Fastec® F14 fittings for use with Fastec® manifold assemblies, incorporated with brass bodies and EPDM O-rings. To be used with copper pipe complying with BS EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Test Point with a DZR brass body. Maximum working pressure 20.0 bar. Maximum operating temperature 99°C.
Range of shower booster pumps (either single or double) with acetal bodies and impellers and EPDM seals and NBR `O` rings. Supplied with stainless-steel braided EPDM lined flexible hoses incorporating isolation valves Please refer to model for maximum operating pressure. Maximum operating temperature 65°C.
Range of combined storage and booster sets, incorporating a cold-water storage cistern, submersible pump, solenoid valve or alternative actuated ball valve, non-return valve (not suitable for backflow protection), isolation valves and expansion vessel. Maximum working pressure 10.0 bar. Cold water use only.
“TP/TPE series 100” single stage centrifugal pumps, incorporating cast iron (with black coloured electrocoating) or stainless-steel bodies and plastic impellers. Maximum working pressure 10.0 bar. Maximum operating temperature: Cast iron models: 60°C, Stainless steel models: 85°C.
Range of pumps with plastic bodies. Maximum working pressures: 41.007.400 model: 0.28 bar, 41.008.400 model: 0.38 bar. Maximum operating temperature 96°C
Ceiling mounted shower outlet (chromium plated) with a concealed ceiling installation box. The inlet to the concealed ceiling installation box incorporates a flow regulator and a single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Open outlet use. Maximum operating temperature 70.0°C
Shower handset with a stainless-steel body (various finishes - see model) and silicone nozzles. The inlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 65°C.
Range of overhead shower and shower handsets with (brass or plastic bodies – various finishes), incorporating a stainless-steel strainer on the inlets. Open outlet use only Maximum operating temperature – 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| VAL2 BIB C CD | Chrome | 1/2" BSP (M) | 5.0 bar | 65 °C | Bristan | Handle | No | 1/2 Turn ceramic disk | Not Applicable | Flow Straightener | |
| VAL2 BIB C 6 CD | Chrome | 1/2" BSP (M) | 5.0 bar | 65 °C | Bristan | Handle | No | 1/2 Turn ceramic disk | Not Applicable | Flow Straightener |
Range of drain taps with brass (or DZR brass, see models) bodies and non-rising spindle headwork. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of wall mounted hose union bib taps incorporating a rising spindle headwork with a T - handle operating member. Products have a brass body. The spout outlets incorporate a hose union connector. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Page 181 of 215
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
