Range of straight, angled, tee and Y shaped isolation valves incorporating brass bodies, NBR ‘O’-rings or PTFE seats depending on model variant. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
‘Floreg’ range of in-line lever operated spherical valve with a DZR brass body (brushed chromium plated) and ball. The product incorporates a stainless-steel mesh strainer and a flow regulator. Compression connection to be used with copper pipe to BS EN 1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of lever operated spherical valves with a brushed chrome plated brass body, brass ball and PTFE seals. . Maximum working pressure 40.0 bar. Maximum operating temperature 85°C.
Range of lever or screwdriver operated in-line spherical valves (chrome plated brass body), brass ball and EPDM seals. Compression connection to be used with copper pipe EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of spherical ball valves having brass, DZR brass or stainless-steel bodies and lever type operating members. For use with stainless steel pipe (EN10312) or copper pipe (EN1057). Maximum working pressure 25.0 Bar. Maximum operating temperature 85.0°C.
Range of spherical valves, with brass bodies (either nickel plated or chromium plated) and a chromium plated brass ball. The products can be supplied with various operating members (see model). The products are to be used with copper pipe (manufactured to EN1057). Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of spherical valves incorporating (brass bodies - various finishes). Maximum working pressure 16.0 bar, 25.0 bar for model 10.61092.015.CP5R-8510 & 10.61092.015.CP12-8510. Maximum operating temperature 85°C.
Range of spherical valves, with DZR brass bodies and brass ball (15mm size) or stainless steel ball (all other sizes). The products can be supplied with various operating members (see model). Jointing is achieved via a crimping tool, the 15-28mm sizes use a ‘M’ profile and the 35-54mm sizes use a ‘V’ profile. The press-fit connection is to be used with copper pipe (manufactured to EN 1057), stainless steel pipes (manufactured to EN10312) or carbon steel pipe (manufactured to EN10305-3). Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with various operating members, brass bodies, brass balls, EPDM ‘O’-rings and PTFE seats. Maximum working pressure 40.0 bar. Maximum operating temperature 85°C.
Range of angled and straight ball valves with plastic valve bodies, PTFE seats and EPDM O-rings. Maximum working pressure 16 bar. Maximum operating temperature 40°C
Range of gate valves with ductile iron bodies (blue epoxy coated), and EPDM coated wedge with hand wheel operating members. Maximum working pressure: 10.0 Bar. Maximum operating temperature: 80 °C
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies and bonnets and ductile iron wedges encapsulated in EPDM. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Gate valve with a blue epoxy coated ductile iron body and an EPDM lined disc, with a non-rising spindle operating mechanism. Maximum operating temperature: 80°C. Maximum working pressure: of 16.0bar.
Range rising spindle screw down stop valves with gunmetal bodies and T-type operating members. Models SCM020000535, SCM025000536, SCI100000533, SCM025002164 & SCM032002165 models are to be used with PE80 pipe manufactured to EN 12201. Maximum working pressure: 12.5 Bar. Maximum operating temperature: 23°C.
Range of electrolytic scale inhibitors incorporating copper bodies. For use with copper pipe complying with BS EN 1057. Maximum working pressure 10.0 bar. Maximum operating temperature 40°C.
Ionisation system with stainless steel body and copper & silver electrodes. Maximum working pressure 12.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Water chiller and heater units for under counter installation incorporating an approved double check valve at the inlet, to be used in conjunction with an outlet tap arrangement or flow control device, with a range of taps that are supplied with the chillers. Maximum working pressure 10.0 Bar Maximum operating temperature 98.0°C
Continuous soft water, ion exchange, hydraulically driven water softener (salt regenerated) for domestic use, incorporating LLDPE tubing. Operation is by an ion exchange resin filed plastic pressure vessel, with integral salt cabinet and timer/manual regeneration control. The appliance incorporates single check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar. Maximum operating temperature Cold water only.
'4.R50760000-01'. Beige coloured, sintered, ceramic rotor shaft. For use with water up to 85°C.
'ITK-STE 221 (cream coloured), ITK-AL 99 (cream coloured) & ITK-AL96 (white coloured)'. Compression moulded and sintered ceramic sealing rings. For use with water up to 85°C.
'EPONICS WP-NS (No. 20170209)'. Factory applied, dark grey coloured, two-component, solvent free epoxy resin coating consisting of a base and hardener. Mix base and hardener in a weight ratio of 7:3 and apply as per Product Data Sheet ‘1838-K’ dated February 2017. Cure for 168 hours@30°C, then 168 hours@60°C and 'rest' for 168 hours before use. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CP231200'. Factory applied, two-part water-based epoxy coating. Mix Parts A & B in a 5:1 weight ratio and apply as per manufacturer's instructions 'File No. HBB-01', 'Version: A', dated '2024.6.30'. Cure for 24 hours@26°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotaguard VA 5001'. Factory applied, blue coloured epoxy coating. Apply as per manufacturers technical data sheet dated 9th November 2015. Cure for 2 minutes, 30 seconds@232°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'90000 KANEPOX SF-A'. Factory applied, two-part, cream or red coloured epoxy coatings consisting of component A and component B. Mix and apply as per data sheet ‘Rev. No. 01’ dated January 2024. Cure for 7 days@23°C. The cream coating is for use with water up to 50°C. Between February 2024 and August 2024, the red coating is for use with water up to 23°C. From September 2024 the red coating is for use with water up to 50°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'TOHPEPOWDER#6150 SHK GRAY QD'. Factory applied, grey coloured epoxy coating. Apply as per Tohpe Corporation instructions no '4230904550B'. dated 'Jan 28, 2025'. Cure for 5 minutes@200°C. For use with water up to 65°C.
'JSGL-BFSC III A (S)'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1:1.7:0.5 weight ratio and apply as per manufacturer's work instructions 'JSGL/WI/14', 'Issue No. 02', 'Revision No. 00', dated '29.09.2018'. Cure for 4 hours@45°C (R.H. 85%). For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSGL-BFSC III B (S)'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1:1.7:0.5 weight ratio and apply as per manufacturer's work instructions 'JSGL/WI/14', 'Issue No. 02', 'Revision No. 00', dated '29.09.2018'. Cure for 4 hours at 45°C (R.H. 85%). For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSGL-BFSC (E)'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1:1.7:0.5 weight ratio and apply as per manufacturer's work instructions 'JSGL/WI/14', 'Issue No. 02', 'Revision No. 00', dated '29.09.2018'. Cure for 4 hours at 45°C (R.H. 85%). For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSGL-SRC (E)'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1:1.7:0.5 weight ratio and apply as per manufacturer's work instructions 'JSGL/WI/14', 'Issue No. 02', 'Revision No. 00', dated '29.09.2018'. Cure for 4 hours@45°C (R.H. 85%). For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Pulron 101 Aqua'. Factory applied, blue coloured PE coating. Apply as per manufacturer's instructions application guide dated 07.02.2018. Cure for 10 minutes@200°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NextGen NP-F9500 PW'. Factory applied, blue coloured powder coating. Apply as per manufacturer's technical data sheet 'FBE/ REV00 01-02-201'. Cure for 3 minutes@240°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘ARC S2 (E)’. Factory applied, two component epoxy ceramic coatings, available in green and grey colours. Mix, apply and cure in accordance with Application Instructions '085031EU' dated 01/25. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that are included in Application Instructions '085031EU' dated 01/25. If the mixing and/or curing conditions are varied from those specified in these instructions then the material is not covered by the scope of the approval.
'JERLAC Two Pack Epoxy Beige-740'. Factory applied, two-part, beige coloured epoxy coating. Mix in a 3:1 volume ratio and apply as per manufacturer's data sheet issue number '01', dated '10.01.2024'. Cure for 7 days@30°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW– JAL (OPC-TICL)'. Factory applied, grey coloured Ordinary Portland Cement. Mix sand, cement & water in a 1.5:1.0:0.5 weight ratio and apply as per manufacturer's instructions 'JSL/QA/PR-06', version '2.0', dated '15.02.20'. Cure for 27 days@21°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (SRPC-DCL)'. Factory applied, grey coloured Sulphate resistant Portland Cement. Mix sand, cement & water in a 1.5:1.0:0.5 weight ratio and apply as per manufacturer's instructions 'JSL/QA/PR-06', version '2.0', dated '15.02.20'. Cure for 27 days@21°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (BFSC-JSL)'. Factory applied, grey coloured Blast furnace slag cement. Mix sand, cement & water in a 1.5:1.0:0.5 weight ratio and apply as per manufacturer's instructions 'JSL/QA/PR-06', version '2.0', dated '15.02.20' and apply as per. Cure for 27 days@21°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Electrocement CEM I-SR3 – Parasakti SRPC)'. Factory applied, grey coloured, Sulphate Resisting Portland Cement. Mix cement, sand & water in a 0.6 : 1.0 : 0.22 mass ratio and apply as per work instructions 'WP-08-05 I', issue '04', rev. '0' dated '22.08.2024. Cure for 24 hours@27°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Hempadur 35530 System’. Grey coloured, factory applied, two-component epoxy coating comprising of ‘Hempadur 35530 red (51320) and Hempadur 35530 grey (10500)’. ‘Hempadur 35530 red (51320)’ comprises of a base and curing agent which are mixed in a 3:1 volume ratio. ‘Hempadur 35530 grey (10500)’ comprises of a base and curing agent which are mixed in a 3:1 volume ratio. Apply as per manufacturer's Product Data Sheet dated October 2024. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Dyopox PTW Red'. Factory applied, red coloured, two-component epoxy coating. Mix base and hardener in a 2:1 weight ratio and apply as per manufacturer's datasheet 'R3 issued 2024'. Cure for 7 days@23°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NextGen NP-F9500 PW'. Factory applied, blue coloured powder coating. Apply as per manufacturer's technical data sheet 'FBE/ REV00 01-02-2019'. Cure for 3 minutes@240°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Nylon 11'. Factory applied nylon coatings available in white or grey colours. The substrate the coating is to be applied to is heated to 310°C for 30 minutes and the coating applied as per manufacturer's work instructions 'WI-09-19 Rev. 6' dated April 22, 2020. Cure for 10 minutes@270°C. The white coating is for use with water up to 23°C. The grey coating is for use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'POLYGEL-2136'. Factory applied, two-part, white coloured (opaque) isophthalic gelcoat comprising of a resin and catalyst. Mix resin and catalyst in a 50:1 mass ratio and apply as per manufacturer's TDS 'Revision No. 10', dated 'SEPT 2024'. Cure for 3 hours@85°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jindal Saw Limited Ordinary Portland Cement - 53 Grade'. Factory applied, grey coloured Ordinary Portland Cement. Mix cement, sand & water in a xx ratio of 1:1.5:0.5 and apply as per manufacturer's Work Instructions 'JSAW/AP01/DISP/PRO/WI-09', version '2.0', effective date '01.05.2023'. Cure for 2.5 hours@48°C and then 3 days@30°C. For use with water up to 60°C.
'RAL 5005 Epoxy Coating'. Factory applied, blue coloured Epoxy Coating. Apply as per manufacturer's TDS '31.05.2024'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hylon N1040 H2 BK397 W & Hylon N1030 H2 BK397 W'. Black coloured, injection moulded, glass fibre filled polyamide materials. For use with water up to 60°C.
'LCPA-G(1)06 HMNC001'. Natural, (appears off-white), injection moulded, glass fibre filled nylon material. (1) 2 digits represent the amount of fiberglass added to the material with a range of 5% (05) - 65%. For use with water up to 85°C.
'ULTRAMID® A3EG10 FC AQUA BLACK23285'. Black coloured, injection moulded PA material. For use with water up to 85°C.
'ULTRAMID® T7300EG10 FC Aqua BK23285'. Black coloured, injection moulded PA66 material. For use with water up to 85°C.
'Celanex 3300-2FC EF2001 natural'. Natural (appears cream coloured), injection moulded PBT material. For use with water up to 60°C.
Page 172 of 204
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
