Range of thermostatic bar shower mixers, (brass bodies – various finishes) incorporating ceramic disc diverter valves with dome type operating members. The temperature is controlled independently via a thermostatic with a dome type operating member that incorporates a manual override button. The inlets incorporate approved single check valve cartridges, however, the complete assembly has not been fully tested to demonstrate that it provides backflow protection. The products are supplied with a shower hose, handset, overhead shower and riser rail assembly. Maximum working pressure 5.0 bar Maximum operating temperature 60°C.
Range of wall mounted thermostatic bar shower mixers (brass bodies – various finishes) incorporating either a quarter turn ceramic disc headwork or two-way ceramic disc diverter with a dome or cubed type operating member. The temperature is controlled independently via a thermostatic cartridge with dome or cubed type operating members that incorporate a manual override button. The inlets incorporate approved single check valve cartridges, however, the complete assembly has not been fully tested to demonstrate that it provides backflow protection. Models ( ET 106, HT 106 & CV 106) are supplied with shower hose, handset, overhead shower and riser rail assembly. Maximum working pressure 5.0 bar. Maximum operating temperature 70°C.
Range of wall mounted thermostatic bar shower mixers incorporating a non-rising spindle headwork controlling the flow. The temperature is controlled independently via a thermostatic cartridge that incorporates a manual override button. Both using either dome, cubed or single lever type operating members. The inlets incorporate stainless steel strainer washers and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products are supplied with a shower hose, handset and riser rail assembly. Maximum working pressure 10 bar. Maximum operating temperature 65°C
Range of wall mounted, concealed, thermostatic shower valves (brass bodies – various finishes) incorporating a quarter turn ceramic disc headwork which controls the flow using various operating members. Temperature is controlled independently via a thermostatic cartridge with a manual override button also using various operating members. Both inlets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 75°C
Range of wafer, lug or flanged butterfly valves (lever or handwheel operation) with cast iron or stainless steel bodies (blue epoxy coated), EPDM seat and stainless-steel disc. Maximum working pressure 16.0 Bar Maximum operating temperature 90.0 to 100.0°C
Range of lever operated butterfly valves incorporating fusion bonded Epoxy coated ductile iron bodies, with stainless steel discs and end faces and EPDM seat. For use with Stainless steel pipe manufactured to EN 10217-7 (or Equivalent). For above and Below ground. Maximum working pressure 16.0 bar Maximum operating temperature 85°C
Range of 2-way ceramic disc diverters, that incorporate a shut off position with plastic bodies. For insertion into specifically dimensioned tap bodies. Maximum working pressure 10.0 Bar. Maximum operating temperature 65 °C.
Wall mounted, concealed, 2-way diverter valve (brass bodies – various finishes) with a dome type operating member. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Wall mounted concealed two way and three way diverter valve assembly (brass bodies with trim sets in various finishes). The 59556 000070 and 59548 000170 concealed installation units are not approved in their own right. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
1451 series of spring loaded, resilient trim, non-return valves with brass bodies. Maximum working pressure 10.0 bar ½” – 1” and 12.0 bar 1 ¼ - 2”. Maximum operating temperature 85°C.
Manually adjustable pressure reducing valves with nickel plated, DZR brass bodies for use with copper pipe (manufactured to EN1057). Maximum supply pressure 16.0 bar. Outlet pressure range between 1.0 & 6.0 bar. Factory pre-set at 3 bar. Maximum operating temperature 85°C.
Range of bronze swing gate valves with bronze bodies and discs (with a metal-to-metal seal). Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of spherical valves with DZR brass bodies, chrome plated brass balls and PTFE seats. The products incorporate a lever type operating members. Maximum working pressure 40.0 bar. Maximum operating temperature 100°C.
Range of spherical valves with (bronze or brass bodies) incorporating a brass or stainless-steel ball with PTFE seat. The 229f range - Maximum operating pressure - 40 bar. Maximum operating temperature 85°C. The 202 range - Maximum operating pressure - 25 bar. Maximum operating temperature - 85°C.
Range of spherical valves with brass bodies, models (127 & 127R) chrome plated brass bodies incorporating chrome plated brass balls and single lever operating members. The products incorporate spigot spout outlets. Models (267, 127, 247, 227 and 248) spout outlets incorporate a plastic flow straightener Maximum working pressure 16.0 Bar. Maximum operating temperature 100.0°C.
Range of in-line angled or ‘T’ type spherical valves with chromium plated brass, nickel plated brass or brass bodies with chromium plated brass balls. Models incorporate lever or butterfly operating members. Maximum working pressure 10.0 Bar, 16 bar, 25 bar, 32 bar, 40 bar or 64 bar. Maximum operating temperature 100 °C.
Range of in-line spherical valves with brass body, brass ball, EPDM O-ring and PTFE gasket. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with brass or DZR brass bodies, chromium plated brass or chromium plated DZR brass (12-18mm) or stainless-steel balls (22-54mm) and various operating members The press-fit connection is for use with copper pipes (manufactured to EN 1057), stainless steel pipes (manufactured to EN10312) or carbon steel pipes (manufactured to EN10305-3). Jointing is achieved via a crimping tool using a ‘M’ profile. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of inline, angled or tee type spherical valves with brass (CP5R models), nickel plated brass (CP12 and CP02 models) or chromium plated brass (CP13 models) bodies, brass (10.20105.22X.CP5R-8510 and 10.20105.28X.CP5R-8510 models) or chromium plated brass (all other models) balls. The valves are either screwdriver, lever or butterfly handle operated (see model). The compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 25.0 bar (10.60145.015.CP12-8510 and 10.61055.022.CP12-8510 models) or 16.0 bar (all other models). Maximum operating temperature 85°C.
Range of screwdriver operated spherical valves incorporating brass bodies and chrome plated brass ball. The compression and press-fit connections are for use with copper pipe (manufactured to EN1057). Jointing of the press-fit connection is achieved via a crimping tool using a ‘M’ profile. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of in-line hex key operated spherical valves incorporating nickel plated or chromium plated brass bodies and chromium plated brass balls. The compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with stainless steel bodies, stainless steel ball and lever operating members. The press-fit connection is for use with stainless steel pipe (manufactured to EN10312). Jointing is achieved via a crimping tool using a ‘M’ profile. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with brass bodies and wedges. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Flomasta Range of plastic, push-fit stop valves for use with MDPE pipe (manufactured to BS EN 12201). Maximum working pressure 16.0 bar. Cold water use only.
Magnetic and electrolytic scale inhibitors incorporating nickel plated copper bodies. For use with copper pipe manufactured to BS EN 1057. Maximum working pressure 10.0 bar. Cold water use only.
UV Home’ range of UV disinfection units with 304L or 316L stainless steel bodies (see models). Maximum working pressure for UV HOME 2 & 3 is 6 bar. Maximum working pressure for UV HOME 6 & 9 is 10 bar. Maximum operating temperature 35°C.
'Powercron 805 B'. Factory applied, blue coloured Acrylic coating. Apply as per manufacturer's TDS 'CR805B/CP826', dated 'Sep 12, 2024'. Cure for 30 minutes@180°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Powercron 451B'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's TDS 'CR451B/CP573X', dated 'Sep 24, 2024'. Cure for 30 minutes@180°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TML Dalmia Sulphate Resisting cement'. Factory applied, grey coloured sulphate resisting cement. Mix cement, sand and water in a mass ratio of 1:1.50:0.50 and apply as per manufacturer's instructions 'TSL/TSMD/DI/QA/TPI/DC/004', dated '09/06/2025'. Cure for 4 hours@28°C. Then 4 hours@45°C. Then 6 hours@40°C (humidity greater than 85%). Then 666 hours@35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'M-AC010'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's user manual 'rev. 2.0R' dated 10/10/2024. Cure for 20 minutes at 180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ZX-9 Fusion Bonded Epoxy Powder Coating Blue & Red'. Factory applied, blue or red coloured epoxy coatings. Apply as per manufacturer's TDS 'ZX-9-HX' dated '2025.4.25'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EB-1003'. Factory applied, blue coloured epoxy powder coating. Apply and cure as per manufacturer's instructions 'Fowry Powder-001' dated '2020.3.20'. For use with water up to 85°C.
'VETOPROOF EC720'. Site applied, grey coloured, two-part epoxy coating. Mix parts A and B in a 84.8:15.2 weight ratio and apply three coats as per manufacturer's Method Statement 'MoS-SA-G1104-M-AK-09-23', dated '18 September 2023'. Cure first coat for 24 hours at 23°C, second coat for 24 hours at 23°C and third coat for 7 days at 23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'VETOPROOF EC722'. Site applied, grey coloured, two-part epoxy coating. Mix parts A and B in a 85.4:14.6 weight ratio and apply three coats as per manufacturer's Method Statement 'MoS-SA-G1101-M-AK-09-23', dated '18 September 2023'. Cure first coat for 24 hours at 23°C, second coat for 24 hours at 23°C and third coat for 7 days at 23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'SINTA-GRP-01 Water Tank Panel'. Natural (appears off-white), hot press moulded GRP panel. For use with water up to 23°C.
'UP 5604 TP' (amber coloured) & 'UP- 4601 TPI' (pink coloured). Unsaturated polyester resin materials manufactured by hand lay-up. For use with water up to 50°C.
'Bingo HDPE Pipes 01'. Black coloured (with blue, external stripes), extruded HDPE pipe. For use with water up to 85°C.
'Hengyuan PE100 Fittings'. Black coloured, injection moulded PE100 fittings. For use with water up to 60°C.
'Ultrason® P 3010 MR grau 30373'. Grey coloured, injection moulded PPSU material. For use with water up to 85°C.
'Lubricomp CG006-NA1G003 Black'. Black coloured, injection moulded polystyrene material. For use with water up to 85°C.
'PRO V200'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions 'Version 7', dated '18/05/2022'. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ASIIR60WRC'. Black coloured, mould pressed isobutylene isoprene rubber. Shore hardness 65. Tested in-radius size 1.0mm. For use with water up to 85°C.
'DL8099F Gaskets and 'O' rings'. Black coloured, compression moulded EPDM gaskets and 'O' rings. Shore hardness 70. Gaskets have an in-radius size of 1.5mm. 'O' rings have an in-radius size of 1.45mm. For use with water up to 85°C.
'EJ820 'O' ring'. Black coloured, compression moulded EPDM 'O' ring. Shore hardness 70. Tested in-radius size 1.3mm. For use with water up to 85°C.
'EP1/1/5 BLK EPDM Diaphragm'. Black coloured, compression moulded EPDM diaphragm. Shore hardness 70. Tested in-radius size 0.65mm. For use with water up to 85°C.
'E103 Sealing Ring'. Black coloured, injection moulded EPDM sealing ring. Shore hardness 70. Tested in-radius size 1.5mm. Between April 2025 and August 2025, the ring was for use with water up to 23°C. Between September 2025 and April 2030, the ring is for use with water up to 85°C.
'Corirubber 4070 gaskets'. Black coloured, compression moulded EPDM rubber gaskets. Shore hardness 70. Tested in-radius size between 1.53mm & 4.01mm. For use with water up to 23°C.
'R210WM'. Black coloured, injection moulded EPDM material. Shore hardness 70. Tested in-radius size 1.2mm. For use with water up to 85°C.
'D0012'. Black coloured EPDM material manufactured by vulcanisation moulding. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 23°C.
'ZXMFJ-50 SEALING'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius 1.25mm. For use with water up to 85°C.
Page 162 of 209
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
