Range of screw down valves with brass or DZR brass bodies, brass or DZR brass bonnets, EPDM washers and PTFE seats. Compression connection to be used with copper pipe manufactured to EN1057. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
Flomasta Range of plastic, push-fit stop valves for use with MDPE pipe (manufactured to BS EN 12201). Maximum working pressure 16.0 bar. Cold water use only.
UV Home’ range of UV disinfection units with 304L or 316L stainless steel bodies (see models). Maximum working pressure for UV HOME 2 & 3 is 6 bar. Maximum working pressure for UV HOME 6 & 9 is 10 bar. Maximum operating temperature 35°C.
'Powercron 805 B'. Factory applied, blue coloured Acrylic coating. Apply as per manufacturer's TDS 'CR805B/CP826', dated 'Sep 12, 2024'. Cure for 30 minutes@180°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TML Dalmia Sulphate Resisting cement'. Factory applied, grey coloured sulphate resisting cement. Mix cement, sand and water in a mass ratio of 1:1.50:0.50 and apply as per manufacturer's instructions 'TSL/TSMD/DI/QA/TPI/DC/004', dated '09/06/2025'. Cure for 4 hours@28°C. Then 4 hours@45°C. Then 6 hours@40°C (humidity greater than 85%). Then 666 hours@35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'VETOPROOF EC722'. Site applied, grey coloured, two-part epoxy coating. Mix parts A and B in a 85.4:14.6 weight ratio and apply three coats as per manufacturer's Method Statement 'MoS-SA-G1101-M-AK-09-23', dated '18 September 2023'. Cure first coat for 24 hours at 23°C, second coat for 24 hours at 23°C and third coat for 7 days at 23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Hinton Easyjoint Silicone Grease (HSG200)'. Off-white coloured (opaque) silicone grease. Apply as per manufacturer's instructions. For use with water up to 65°C.
'Radilon A RCM4010RKC 306 BK'. Black coloured, injection moulded, glass filled PA66 material. For use with water up to 85°C.
'UP 5604 TP' (amber coloured) & 'UP- 4601 TPI' (pink coloured). Unsaturated polyester resin materials manufactured by hand lay-up. For use with water up to 50°C.
'TAP HDPE Fittings'. Black or blue coloured fittings manufactured by extrusion and fabrication (butt fusion process), extrusion and swept bend, extrusion and machining (lathe) & injection moulding. For use with water up to 65°C.
'TAP HDPE Pipe'. Blue or black coloured, extruded HDPE pipes. For use with water up to 65°C.
'Cosmoplast HDPE & MDPE Pipes'. Black coloured, extruded polyethylene pipes. For use with water up to 60°C.
'Cosmoplast LDPE Pipe'. Black coloured, extruded LDPE pipe. For use with water up to 65°C.
'Hengyuan PE100 Fittings'. Black coloured, injection moulded PE100 fittings. For use with water up to 60°C.
‘Polytank 4 Layer Multilayer LLDPE Tank Panel'. Multi-layered LLDPE tank panel, manufactured by rotational moulding, consisting of a white coloured inner layer, light grey coloured second layer, black coloured third layer & white coloured outer layer. For use with water up to 65°C.
'Lubricomp CG006-NA1G003 Black'. Black coloured, injection moulded polystyrene material. For use with water up to 85°C.
'ASIIR60WRC'. Black coloured, mould pressed isobutylene isoprene rubber. Shore hardness 65. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EPW50, EPW55, EPW60, EPW65, EPW70, EPW75 & EPW80'. Black coloured, injection moulded EPDM material. Shore hardness between 50 & 80. Tested in-radius 2.95mm. For use with water up to 65°C.
'E-Tupling Plastic Pipe Cement 125 ml ETSC125' & 'E-Tupling Plastic Pipe Cement 250 ml ETSC250'. Clear, transparent (un-pigmented) solvent cements, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions 'Rev00 08052025'. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TODAY TOOLS PVC SOLVENT CEMENT 125ML SC1' & 'TODAY TOOLS PVC SOLVENT CEMENT 250ML SC2'. Clear, transparent (un-pigmented) solvent cement, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions 'Rev00 08052025'. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TW Tools PVC Pipe Cement 125ml' & 'TW Tools PVC Pipe Cement 250ml'. Clear, transparent (un-pigmented) solvent cement, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions 'Rev00 08052025'. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of electronic, touch free, wall-mounted taps (chromium plated brass. The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 Bar Maximum operating temperature 65.0°C
Range of BS1212-4 (2016) compact type float operated valves for WC flushing cisterns, with either bottom entry (A28-06 XXX models) or side entry (A28-06 side). The inlet incorporates a plastic strainer. Maximum working pressure 10.0 Bar Cold Water Use Only
Bottom entry BS1212-4 (2016) compact type float operated valves for use with WC flushing cisterns. The inlet incorporates a strainer. Maximum working pressure 10.0 bar. Cold water use only.
Range of single check valve assemblies consisting of a single check valve cartridge housed within a DZR brass body. Compression connections on for use with popper pipe to BS EN1057. Maximum working pressure 16 Bar. Maximum operating temperature 65°C.
Non-verifiable double check valve assembly with DZR brass body consisting of two spring loaded, resilient trim in-line check valve cartridges, incorporating a lever operated spherical valve. Maximum working pressure 10 Bar Cold water use
Range of ceramic cartridge headworks with plastic bodies. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of single hole, single outlet (swivel) combination tap assemblies incorporating a brass body (various finishes) and ceramic cartridge headwork with single lever operating members. The outlets incorporate a plastic aerator. Model 63785-00XX incorporates a pull-out spray with push button trigger assembly. The pull-out spray incorporates a single check valve assembly (however the complete unit has not been tested to demonstrate it provides adequate backflow protection). Model 63787-00XX incorporates a pull-down outlet. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet, fixed combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Model 33528671 is supplied with a lever type pop up waste – not verified by test. Maximum working pressure - 10 Bar Maximum operating temperature - 70 °C
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator Maximum working pressure 10.0 Bar Maximum operating temperature 60 °C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 193746 X XXX | VARIOUS | 1/2" BSP | 5.0 bar | 85 °C | PPI | REAR OF BODY | No | Ceramic cartridge | C-plate | Flow Straightener |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass) incorporating a quarter turn ceramic disc headwork with a dome type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet (swivel) combination tap assemblies (chrome plated brass bodies) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 70.0°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge or quarter turn ceramic disc headworks with a single lever operating member. The spout outlets incorporate an aerator. Models Prime, Specto and Linear have approved check valve cartridges in the inlets, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass body - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Two hole, single outlet fixed combination tap assembly (chrome plated brass body) incorporating quarter turn ceramic disc valve headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. Product is supplied with metal back nuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| COB BF C | CHROME | 3/4" BSP (M) | 5 bar | 60 °C | Bristan | Handle or Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| RP3 COB BF C | CROME | 3/4" BSP (M) | 5 bar | 60 °C | Bristan | Handle or Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| COB BF BLK | BLACK | 3/4" BSP (M) | 5 bar | 60 °C | Bristan | Handle or Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| 144347 | CHROME | 3/4" BSP (M) | 5 bar | 60 °C | Bristan | Handle or Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| 257580 | BLACK | 3/4" BSP (M) | 5 bar | 60 °C | Bristan | Handle or Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener |
Floor mounted, two-hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disc headworks with cross top operating members and a manually operated diverter to shower outlet with a single lever operating member. The product is supplied with an approved shower hose and handset. Product is to be installed with a floor mounting kit. Maximum working pressure 10.0 Bar Maximum operating temperature 70.0°C
Range of deck mounted three-hole, single outlet (fixed) combination tap assemblies (various plated brass), incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure: 10.0 Bar. Maximum operating temperature: 60.0°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| CLS201 | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| CLS211 | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| CLS214 | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| CLS215 | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS210 | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS220 | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS230 | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS22A | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS22B | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS22C | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS22D | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS22E | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS24A | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS24B | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS24C | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
Finishes available: Chrome, Brass, Burnished Brass, Burnished Nickel, Matte Nickel, Copper, Dark Brass, Vintage Brass, Gold, Matte Gold.
Three-hole, single outlet (swivel) combination tap assembly, incorporating quarter turn ceramic disc headworks with single lever type operating members. The spout outlet is connected to the headwork with a PEX lined braided hose and incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of bath filler waste kits incorporating a brass inlet elbow and overflow assembly, a copper hex nut, overflow housing. Maximum Working Pressure 5.0 bar. Maximum operating temperature 70.0 C
Deck mounted swivel spout outlet (chromium plated brass). Open outlet use only. Maximum operating temperature 65°C.
Range of stainless-steel expansion joints. Maximum working pressure 6.0 bar. Maximum operating temperature 90°C.
Range of stainless steel axial expansion joints (various end connections - see model). Maximum operating pressure 16.0 bar. Maximum operating temperature 100°C.
TY-11 & TY-03 ranges of expansion vessels. The TY-11 range has an epoxy coated carbon steel body and the TY-03 range has a stainless-steel body. Maximum working pressure 10.0 bar. Maximum operating temperature 99°C.
‘Center Pot’ range of expansion vessels. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of clamp fittings incorporating DZR brass bodies. For use with PE 100 RC pipe (manufactured to EN12201) only. Maximum operating pressure: 16 bar. Cold water use only.
Range of Instantor Irish Compression Fittings with brass bodies for use with copper pipe to EN1057. Maximum working pressure 16 bar. Maximum operating temperature 99°C.
FLOWTECH range of fusion welded, PP-RCT fittings for use with Atlas PP-RCTGF pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Page 154 of 171
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
