Range of motorised spherical valves with stainless steel bodies, ball and PTFE seals Maximum working pressure 16.0 bar. Maximum operating temperature 99˚C.
Range of spherical valves with nickel platedbrass bodies, nickel plated brass balls and EDPM ‘O’-rings with a lever type operating member. Maximum working pressure 50.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with a brass body brass ball (chrome plated), PTFE gaskets, EPDM ‘O’-rings and a single lever operating member. Maximum working pressure 10.0 bar. Maximum working temperature 100°C.
Range of gate valves (gunmetal) with gunmetal bronze wedges, brass spindle and PTFE seals. Maximum working pressure 20.0 bar. Maximum operating temperature 100°C.
Range of gate valves incorporating bronze bodies and wedges with PTFE seals. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating bronze bodies and wedges with PTFE seals. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating brass bodies and wedge with PTFE seals. The valves operate via a non-rising spindle headwork that incorporates a wheel type operating member. Maximum working pressure 20.0 Bar. Maximum operating temperature 85°C.
Range of gate valves incorporating bronze bodies and wedges with PTFE seals. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated ductile iron bodies, EPDM coated ductile iron wedges. The valves operate via a non-rising spindle headwork with hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of hand wheel operated gate valves with bronze bodies, bronze wedges, non rising spindles and graphite gaskets. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of gate valves incorporating bronze bodies and wedges with PTFE seals. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated ductile iron bodies, EPDM coated ductile iron wedges. The valves operate via a non-rising spindle headwork with hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of front-loading commercial washing machines with flow controlled by solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). The machines are supplied with double check valve assemblies (suitable for backflow protection against Fluid Category 3) Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of inline water meter kits incorporating brass bodies, a spherical valve and drain off valve. Maximum working pressure 10.0 bar. Cold water use only.
'A8401700'. White coloured, compression moulded Ceramic Alumina Al960 sealing ring. For use with water up to 85°C.
'YS-01 Powder Coating'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instruction document 'HJ-Q-SOP-05' dated 2020-1-10. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MS1545A Enamel Coating'. Factory applied, blue coloured enamel coating. Apply as per document reference 'WRAS-sample-0001' dated 29.10.2020. Cure for 19 minutes (14 minutes in burner zone) @860°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'XX-CM1'. Factory applied, grey coloured cement mortar. Mix and apply as per manufacturer's safety data sheet 'A1: 26-01-2020'. Cure for 5 hours@30°C and then steam cure for 6 hours@30°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'XX-CM2'. Factory applied, grey coloured cement mortar. Mix and apply as per manufacturer's safety data sheet 'A1: 26-01-2020'. Cure for 5 hours@30°C and then steam cure for 6 hours@30°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'XX-CM3'. Factory applied, grey coloured sulphate resistant cement mortar. Mix and apply as per manufacturer's safety data sheet 'A1: 26-01-2015'. Cure for 5 hours@30°C and then steam cure for 6 hours@30°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
Page 16 of 508
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
