'Dubai Polymer UPVC Pipes HP2CLASSe'. Grey coloured, extruded UPVC pipe. For use with water up to 65°C.
'Monomix'. Site applied, grey coloured cementitious repair mortar. Mix Monomix and water in a mass ratio of 7.58:1. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'WS 9000'. Site applied, off-white coloured, fibre glass impregnated, polyurethane repair tape. Apply as per manufacturer's technical date sheet created '02/11/2010' and reviewed '30/01/2015'. Cure for 30 minutes@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EP6008'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 60. Tested in-radius size 0.8mm. For use with water up to 85°C.
`EP2/9/10 BLK 'O' rings`. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size 1.2mm. For use with water up to 85°C.
`EP11/01/13 BLK 'O' rings & seals`. Black coloured, injection moulded 'O' rings & seals. Shore hardness 60. The 'O' rings have a tested in-radius size of 1.8mm. The seals have a tested in-radius size of 0.75mm. For use with water up to 85°C.
`H34-50 to H34-70’. Range of black coloured, compression moulded EPDM rubber materials with a shore hardness of between 50 & 70. Tested in-radius size 1.0mm. For use with water up to 23°C.
'EP60-WAUK-FR'. Black coloured, compression moulded EPDM sheet material. Shore hardness 60. In-radius size 1.35mm. For use with water up to 23°C.
‘EPDM 825-c’. Black coloured, compression moulded EPDM sheet material. Shore hardness 80 A. Tested in-radius size 1.0mm. For use with water up to 23°C.
'EP210107'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 65°C.
'OYRTEP7011PWRC'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.5mm. For use with water up to 65°C.
`SP402`. Black coloured, compression moulded, natural rubber material. Shore hardness 75. Tested in-radius size 1.00mm. For use with water up to 23°C.
'5080SIL310P‐N' (natural - clear) & '5080SIL310P‐B' (black coloured). Extruded, silicone rubber hoses. Shore hardness 70. Tested in-radius size 0.75mm. For use with water up to 85°C.
'Loctite 542'. Site applied, red coloured anaerobic adhesive. For use with water up to 85°C. These products are to be applied and cured in strict accordance with the manufacturer's instructions.
Sonlok 3243 & 3577. Site applied anaerobic adhesives. Apply and cure as per manufacturer's instructions. Sonlok 3243 is blue coloured and is for use with water up to 85°C. Sonlok 3577 is green coloured and is for use with water up to 23°C.
'Durethan BKV30F 901510 SR1'. Black coloured, injection moulded thermoplastic resin. For use with water up to 65°C.
'THERMOLAST K TF5WHA, TF6WHB, TF6WHA, TF7WHB, TF7WHA, TF8WHB & TF8WHA'. Injection moulded, natural (appears off-white translucent) TPE materials with a shore hardness of between 55 and 85. Tested in-radius size 1.0mm. The materials may be coloured using one, or any combination of, the following Kraiburg pigments (up to and including the maximum level included): Black (maximum level 3%). White (maximum level 2%). Blue (maximum level 2%). Orange (maximum level 2%). Yellow 1 (maximum level 2%). Yellow 2 (maximum level 2%). Yellow 3 (maximum level 2%). Green (maximum level 2%). Red 1 (maximum level 2%). Red 2 (maximum level 2%). Brown (maximum level 2%). For use with water up to 65°C.
'3P-PIPE uPVC PIPE Grey'. Extruded, grey coloured uPVC pipe. For use with water up to 23°C.
'3P-PIPE uPVC PIPE White'. Extruded, white coloured uPVC pipe. For use with water up to 23°C.
Single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The inlet to the solenoid incorporates a stainless-steel strainer. The product is supplied with a stainless-steel braided EPDM lined flexible hose assembly for installation between the solenoid valve and the tap body. The spout outlet incorporates a plastic aerator with built in flow regulator. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Side entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. The inlet incorporates a flow restrictor. Maximum working pressure 10.0 bar. Cold water use only.
Range of BS1212-4 diaphragm type inlet valves incorporating a plastic body for use in either side or bottom entry WC cisterns. The valves incorporate an up and over discharge, plastic arm and float. The inlet is fitted with a plastic flow regulator and strainer. Maximum working pressure 10 bar. Cold water use only.
Spring loaded resilient trim, in-line check valve cartridge with plastic guides and stem and NBR seals within a plastic housing. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 16.0 bar & maximum operating temperature 65°C.
Spring loaded resilient trim, in-line check valve cartridges incorporating plastic guides and stem, NBR or EPDM seals within a plastic housing. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 16.0 Bar. Maximum operating temperature 65°C.
Range of single check valve cartridges incorporating a plastic body, stainless steel spring, NBR or EPDM seals. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
Spring loaded resilient trim, in-line check valve cartridge with plastic guides and stem and silicone seals within a plastic housing. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 16.0 bar Maximum operating temperature 65°C.
Single hole bidet tap with brass body (various finishes) fixed spout outlet and a ceramic disc headwork (various operating members). The outlet incorporates an aerator and the product is supplied with a pop-up waste. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
Range of quarter turn ceramic disc headwork assemblies with brass bodies, NBR ‘O’-rings and silicone gaskets. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks incorporating a plastic body for insertion into specifically dimensioned tap assemblies. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Single hole, single outlet (swivel), combination tap assembly (chromium plated brass) incorporating a ceramic cartridge headwork with single lever operating member. The product incorporates a pull-out spout outlet with a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, two hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating a quarter turn ceramic disk headwork with a single lever operating member. The product incorporates a hand held pre-rinse spray with a self-closing trigger on a flexible hose within an overhead spring. Models are available with an additional swivel spout outlet, which incorporates a plastic aerator (see model). The swivel spouts have their own flow control in addition to the main headwork, this is also a quarter turn ceramic disk headwork with a single lever operating member. The inlets incorporate an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with metal backnuts. Maximum working pressure 8.62 bar. Maximum operating temperature 60°C.
Range of wall mounted, two hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disk headworks with single lever operating members. The product incorporates a hand held pre-rinse spray with a self-closing trigger, either on a flexible hose within an overhead spring or as a fixed length flexible hose on a swivel arm (see model). Models are available with an additional swivel spout outlet, which incorporates a plastic aerator (see model). The swivel spouts have their own flow control in addition to the main headwork, this is also a quarter turn ceramic disk headwork with a single lever operating member. Each inlet incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with metal backnuts. Maximum working pressure 8.62 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet fixed combination tap assemblies (chrome plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. Model BTZ 1HF C incorporates a plastic flow straightener. Model BTZ SMBAS C incorporates a plastic aerator. Maximum operating pressure 5.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass). Incorporating ceramic cartridge headworks, and single lever operating members. The spout outlet incorporates a plastic aerator and the product is supplied with a pop up waste. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes - see model), incorporating ceramic a cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assembly with a brushed stainless-steel body, incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single-hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Some models are supplied with click type or pop-up wastes. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The 36 110 000 model is supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disc headworks with cross top operating members. The spout outlet incorporates a plastic aerator. The product is supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The products are supplied with a brass ⅜” BSP (M) x 15mm compression adapter. The spout outlets incorporate a plastic aerator. The A6259AA model is supplied with pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly with brass body (chrom plated). Incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.5 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chrome plated brass), incorporating ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with single check valves with integral servicing valve for both inlets (suitable for backflow protection against Fluid Category 2). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (swivel) combination tap assemblies (chrome plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet can incorporate either a plastic flow straightener or a plastic aerator. When supplied with a plastic flow straightener there is a combined EPDM washer and stainless steel strainer behind it. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of single hole single outlet (swivel) combination tap assmeblies with quarter turn ceramic disc headworks and single lever operating members. The outlet incorporates a plastic aerator. Maximum working pressure 5.5 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes), incorporating quarter turn ceramic disc headworks with either single lever or cross top operating members. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel), combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Page 14 of 71
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
