Directory Search Results

Print List

#240704704

Range of wall mounted gas fired condensing instantaneous water heaters. Maximum working pressure 10.0bar. Maximum operating temperature 85°C.

Section:
1465 Heaters
Section Subtitle:
Combination boilers and Water Jacketed Tube heaters. Low volume water content. Heat retained in water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within the system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.
WRAS Approval Number:
240704704
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
½” BSP(M) for 10-12L & 14~17L/min (Flow rate) ¾” BSP(M) for 22~26L/min (Flow rate)
Marking:
Company Logo Vanward, model, pressure, tempeture and and other technical info on adhesive label on side panel.
Installation Requirements:
R001
Expiry date:
31/07/2029
Model:
10~12L balance type & forces exhaust type gas water heater: JSG=balance type gas water heater, JSQ=forces exhaust type gas water, a= nominal heat input(kW) (fixed from 20, 22 to 24), b=volume (fixed from 10, 11 to 12), STc=Sd= the type of casing (c fixed from 27, 28 to 29, d fixed from 21, 25, 22, 21B, 23, 24, 25(A), 25(B), 26, 27, 28, 31, 32, 34 to 35) Casing 1: ST27, S21, Casing 2: ST28, S25, Casing 3: ST29, S22, Casing 4: S21B, Casing 5: S23, Casing 6: S24, Casing 7: S25(A), Casing 8: S25(B), Casing 9: S26, Casing 10: S27, Casing 11: S28, Casing 12: S31, Casing 13: S32, Casing 14: S34, Casing 15: S35. Where a typical code is: ①JSG28-14ST28、JSG14ST-S25: JSG=balance type gas water heater 28=nominal heat input(kW) 14=volume ST28=the type of casing, ST=structure platform S25=the type of casing 14~17L balance type & forces exhaust type gas water heater: JSG=balance type gas water heater, JSQ=forces exhaust type gas water, a= nominal heat input(kW) (fixed from 20, 22 to 24), b=volume (fixed from 10, 11 to 12), STc=Sd= the type of casing (c fixed from 27, 28 to 29, d fixed from 21, 25, 22, 21B, 23, 24, 25(A), 25(B), 27, 28, 31, 32, 34 to 35). Same casings as above but without casing 9. ②JSG14ST-S25(B) 、JSQ28-14ST28 JSG=balance type gas water heater JSQ=forces exhaust type gas water 14=volume 28=nominal heat input(kW) ST=structure platform S25(B)=the type of casing, ST28=the type of casing 22~26L outdoor type gas water heater: JSW=outdoor type gas water heater, a= nominal heat input(kW) (fixed from 44 to 52), b=volume (fixed from 22 to 26), ST58=Wd= the type of casing (d fixed from 81, 82, 83 to 84), Casing 1: ST58, W81, Casing 2: W82, Casing 3: W83, Casing 4: W84. ③JSW44-22ST58、 JSW22HT-W81: JSW=outdoor type gas water heater 44=nominal heat input(kW) 22=volume ST58=the type of casing, HT=structure platform W81=the type of casing
JSG20-10ST27, JSG10ST-S21, JSQ20-10ST27, JSQ10ST-S21, JSG22-11ST27, JSG11ST-S21, JSQ22-11ST27, JSQ11ST-S21, JSG24-12ST27, JSG12ST-S21, JSQ24-12ST27, JSQ12ST-S21, JSG20-10ST28, JSG10ST-S25, JSQ20-10ST28, JSQ10ST-S25, JSG22-11ST28, JSG11ST-S25, JSQ22-11ST28, JSQ11ST-S25, JSG24-12ST28, JSG12ST-S25, JSQ24-12ST28, JSQ12ST-S25, JSG20-10ST29, JSG10ST-S22, JSQ20-10ST29, JSQ10ST-S22, JSG22-11ST29, JSG11ST-S22, JSQ22-11ST29, JSQ11ST-S22, JSG24-12ST29, JSG12ST-S22, JSQ24-12ST29, JSQ12ST-S22, JSG10ST-S21B, JSQ10ST-S21B, JSG11ST-S21B, JSQ11ST-S21B, JSG12ST-S21B, JSQ12ST-S21B, JSG10ST-S23, JSQ10ST-S23, JSG11ST-S23, JSQ11ST-S23, JSG12ST-S23, JSQ12ST-S23, JSG10ST-S24, JSQ10ST-S24, JSG11ST-S24, JSQ11ST-S24, JSG12ST-S24, JSQ12ST-S24, JSG10ST-S25(A), JSQ10ST-S25(A), JSG11ST-S25(A), JSQ11ST-S25(A), JSG12ST-S25(A), JSQ12ST-S25(A), JSG10ST-S25(B), JSQ10ST-S25(B), JSG11ST-S25(B), JSQ11ST-S25(B), JSG12ST-S25(B), JSQ12ST-S25(B), JSG10ST-S26, JSQ10ST-S26, JSG12ST-S26, JSQ12ST-S26, JSG10ST-S27, JSQ10ST-S27, JSG12ST-S27, JSQ12ST-S27, JSG10ST-S28, JSQ10ST-S28, JSG12ST-S28, JSQ12ST-S28, JSG10ST-S31, JSQ10ST-S31, JSG12ST-S31, JSQ12ST-S31, JSG10ST-S32, JSQ10ST-S32, JSG12ST-S32, JSQ12ST-S32, JSG10ST-S34, JSQ10ST-S34, JSG12ST-S34, JSQ12ST-S34, JSG10ST-S35, JSQ10ST-S35, JSG11ST-S35, JSQ11ST-S35, JSG12ST-S35, JSQ12ST-S35. JSG28-14ST27, JSG14ST-S21, JSQ28-14ST27, JSQ14ST-S21, JSG30-16ST27, JSG16ST-S21, JSQ30-16ST27, JSQ16ST-S21, JSG31-17ST27, JSG17ST-S21, JSQ31-17ST27, JSQ17ST-S21, JSG28-14ST28, JSG14ST-S25, JSQ28-14ST28, JSQ14ST-S25, JSG30-16ST28, JSG16ST-S25, JSQ30-16ST28, JSQ16ST-S25, JSG31-17ST28, JSG17ST-S25, JSQ31-17ST28, JSQ17ST-S25, JSG28-14ST29, JSG14ST-S22, JSQ28-14ST29, JSQ14ST-S22, JSG30-16ST29, JSG16ST-S22, JSQ30-16ST29, JSQ16ST-S22, JSG31-17ST29, JSG17ST-S22, JSQ31-17ST29, JSQ17ST-S22, JSG14ST-S21B, JSQ14ST-S21B, JSG16ST-S21B, JSQ16ST-S21B, JSG17ST-S21B, JSQ17ST-S21B, JSG14ST-S23, JSQ14ST-S23, JSG16ST-S23, JSQ16ST-S23, JSG17ST-S23, JSQ17ST-S23, JSG14ST-S24, JSQ14ST-S24, JSG16ST-S24, JSQ16ST-S24, JSG17ST-S24, JSQ17ST-S24, JSG14ST-S25(A), JSQ14ST-S25(A), JSG16ST-S25(A), JSQ16ST-S25(A), JSG17ST-S25(A), JSQ17ST-S25(A), JSG14ST-S25(B), JSQ14ST-S25(B), JSG16ST-S25(B), JSQ16ST-S25(B), JSG17ST-S25(B), JSQ17ST-S25(B), JSG14ST-S27, JSQ14ST-S27, JSG16ST-S27, JSQ16ST-S27, JSG14ST-S28, JSQ14ST-S28, JSG16ST-S28, JSQ16ST-S28, JSG14ST-S31, JSQ14ST-S31, JSG16ST-S31, JSQ16ST-S31, JSG14ST-S32, JSQ14ST-S32, JSG16ST-S32, JSQ16ST-S32, JSG14ST-S34, JSQ14ST-S34, JSG16ST-S34, JSQ16ST-S34, JSG14ST-S35, JSQ14ST-S35,JSG16ST-S35, JSQ16ST-S35. JSW44-22ST58, JSW22HT-W81, JSW52-26ST58, JSW26HT-W81, JSW22HT-W82, JSW26HT-W82, JSW22HT-W83, JSW26HT-W83, JSW22HT-W84, JSW26HT-W84.

Approval Holder:
Guangdong Vanward New Electric Co. Ltd.
Company Name
Guangdong Vanward New Electric Co. Ltd.
Address
13 Jianye Mid- Road Shunde High Tech Industry Development Zone
Country
Ronggui Shunde

View All Listings by this Company
Manufacturer:
Guangdong Vanward New Electric Co. Ltd.
Company Name
Guangdong Vanward New Electric Co. Ltd.
Address
13 Jianye Mid- Road Shunde High Tech Industry Development Zone
Country
Ronggui Shunde

View All Listings by this Company

Print This Approval


#240902039

Range of VEGAPULS radar sensors for level measurement with plastic bodies. Cold water use only. Open outlet use only.

Section:
1530 Miscellaneous Fittings
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
See model key
Marking:
VEGA logo date of manufacturer (YYYY), serial number and other technical data on body
Installation Requirements:
R001
Expiry date:
30/09/2029
Model:
PSC21.ab-c-d-N-f-g-h-I VEGAPULS C 21 PSC22.ab-c-d- N -f-g-h-I VEGAPULS C 22 PSC23.ab-c-d- N -f-g-h-I VEGAPULS C 23 PS21.ab-c-d- N -f-g-h-I VEGAPULS 21 PS31.ab-c-d- N -f-g-h-I VEGAPULS 31 KEY FOR VEGAPULS C 21 ab = explosion protection, which can be displayed as; XX without, for Ex-free area (CE, UKCA, RCM, EAC) VH ATEX/UKEX/IEC/c-FM-us/c-CSA-us; Gas, intrinsic safety, Zone 0, 0/1, 1, 2 (Class I Division 1, 2) + Dust, intrinsic safety, Zone 20, 20/21, 21, 22 (Class II, III Division 1, 2) VB ATEX/UKEX/IEC; Gas, Encapsulation, Zone 1, 2 + Dust, Protection by enclosure, Zone 20, 21/22, 21, 22 SH EAC/SEPRO; Gas, intrinsic safety; Zone 0, 0/1, 1, 2 + Dust, intrinsic safety Zone 20, 20/21, 21, 22 SB EAC/SEPRO; Gas, encapsulation, Zone 1, 2 + Dust, encapsulation Zone 21, 22 TH CCOE/NEPSI/KTL/TIIS; Gas, Intrinsic safety, Zone 0, 0/1, 1, 2 + Dust, Intrinsic safety, Zone 20, 20/21, 21, 22 (not CCOE) TB CCOE, NEPSI, KTL, TIIS; Gas, encapsulation, Zone 1, 2 + Dust, protection by enclosure, Zone 20, 21/22, 21, 22 (not CCOE) WH INMETRO/IA; Gas, intrinsic safety, Zone 0, 0/1, 1, 2 + Dust, intrinsic safety, Zone 20, 20/21, 21, 22 WB INMETRO/IA; Gas, encapsulation, Zone 1, 2 + Dust, protection by enclosure, Zone 20, 21/22, 21, 22 FB c-FM-us/c-CSA-us; Gas, encapsulation, Zone 1, 2 (Class I Division 2) + Dust, protection by enclosure, Zone 20, 20/21, 21, 22 (Class II, III Division 1) FR c-FM-us/c-CSA-us; Gas, non-incendive, Class I Division 2 + Dust-ignitionproof, Class II, III Division 1 c = Approved as overfill protection, which can be displayed as; X without W with (WHG, VLAREM) d = Ship approval, which can be displayed as; X without S with (CCS, RINA, NK, ABS, DNV GL, LR, BV) N = Foodstuff / Pharmaceutical certificate, which can be displayed as; X without N with (NSF/ANSI/CAN 61) P with (NIH) F with (FDA, EG1935/2004) f = Thread process side / Cable side, which can be displayed as; G Thread G1½ / G1 N Thread 1½NPT / 1NPT R Thread R1½ / R1 g = Cable material / Length, which can be displayed as; A PUR / 5m (approx. 16ft) B PUR / 10m (approx. 32ft) H PUR / 15m (appr. 48ft) J PUR / 20m (appr. 64ft) C PUR / 25m (approx. 82ft) D PUR / individually selectable (acc. to CE, RCM, EAC) D PUR / individually selectable (acc. to c-FM-us, c-CSA-us) h = Electronics, which can be displayed as; H Two-wire 4 ... 20 mA/HART W Four-wire Modbus S Three-wire SDI12 i = Sensor setting via smartphone and VEGA Tools app, which can be displayed as; X without B with KEY FOR VEGAPULS C 22 ab = Explosion protection, which can be displayed as; XX without, for Ex-free area (CE, UKCA, c-FM-us, c-CSA-us, RCM, EAC) VH ATEX/UKEX/IEC/c-FM-us/c-CSA-us; Gas, intrinsic safety, Zone 0, 0/1, 1, 2 (Class I Division 1, 2) + Dust, intrinsic safety, Zone 20, 20/21, 21, 22 (Class II, III Division 1, 2) VB ATEX/UKEX/IEC; Gas, Encapsulation, Zone 1, 2 + Dust, Protection by enclosure, Zone 20, 21/22, 21, 22 SH EAC/SEPRO; Gas, intrinsic safety; Zone 0, 0/1, 1, 2 + Dust, intrinsic safety Zone 20, 20/21, 21, 22 SB EAC/SEPRO; Gas, encapsulation, Zone 1, 2 + Dust, encapsulation Zone 21, 22 TH CCOE/NEPSI/KTL/TIIS; Gas, Intrinsic safety, Zone 0, 0/1, 1, 2 + Dust, Intrinsic safety, Zone 20, 20/21, 21, 22 (not CCOE) TB CCOE, NEPSI, KTL, TIIS; Gas, encapsulation, Zone 1, 2 + Dust, protection by enclosure, Zone 20, 21/22, 21, 22 (not CCOE) WH INMETRO/IA; Gas, intrinsic safety, Zone 0, 0/1, 1, 2 + Dust, intrinsic safety, Zone 20, 20/21, 21, 22 WB INMETRO/IA; Gas, encapsulation, Zone 1, 2 + Dust, protection by enclosure, Zone 20, 21/22, 21, 22 FB c-FM-us/c-CSA-us; Gas, encapsulation, Zone 1, 2 (Class I Division 2) + Dust, protection by enclosure, Zone 20, 20/21, 21, 22 (Class II, III Division 1) FR c-FM-us/c-CSA-us; Gas, non-incendive, Class I Division 2 + Dust-ignition proof, Class II, III Division 1 c = Approved as overfill protection, which can be displayed as; X without W with (WHG, VLAREM) d = Ship approval, which can be displayed as; X without S with (CCS, RINA, NK, ABS, DNV GL, LR, BV) N = Foodstuff / Pharmaceutical certificate, which can be displayed as: X without N with (NSF/ANSI/CAN 61) P with (NIH) F with (FDA, EG1935/2004) f = Process fitting, which can be displayed as; G Thread G1½ N Thread 1½NPT R Thread R1½ g = Cable material / length, which can be displayed as; A PUR / 5m (approx. 16ft) B PUR / 10m (approx. 32ft) H PUR / 15m (appr. 48ft) J PUR / 20m (appr. 64ft) C PUR / 25m (approx. 82ft) D PUR / individually selectable (acc. to CE, RCM, EAC) D PUR / individually selectable (acc. to c-FM-us, c-CSA-us) h = Electronics, which can be displayed as; H Two-wire 4 ... 20 mA/HART W Four-wire Modbus S Three-wire SDI12 i = Sensor setting via smartphone and VEGA Tools app, which can be displayed as; X without B with KEY FOR VEGAPULS C 23 ab = explosion protection, which can be displayed as; XX without, for Ex-free area (CE, UKCA, RCM, EAC) VH ATEX/UKEX/IEC/c-FM-us/c-CSA-us; Gas, intrinsic safety, Zone 0, 0/1, 1, 2 (Class I Division 1, 2) + Dust, intrinsic safety, Zone 20, 20/21, 21, 22 (Class II, III Division 1, 2) VB ATEX/UKEX/IEC; Gas, Encapsulation, Zone 1, 2 + Dust, Protection by enclosure, Zone 20, 21/22, 21, 22 SH EAC/SEPRO; Gas, intrinsic safety; Zone 0, 0/1, 1, 2 + Dust, intrinsic safety Zone 20, 20/21, 21, 22 SB EAC/SEPRO; Gas, encapsulation, Zone 1, 2 + Dust, encapsulation Zone 21, 22 TH CCOE/NEPSI/KTL/TIIS; Gas, Intrinsic safety, Zone 0, 0/1, 1, 2 + Dust, Intrinsic safety, Zone 20, 20/21, 21, 22 (not CCOE) TB CCOE, NEPSI, KTL, TIIS; Gas, encapsulation, Zone 1, 2 + Dust, protection by enclosure, Zone 20, 21/22, 21, 22 (not CCOE) WH INMETRO/IA; Gas, intrinsic safety, Zone 0, 0/1, 1, 2 + Dust, intrinsic safety, Zone 20, 20/21, 21, 22 WB INMETRO/IA; Gas, encapsulation, Zone 1, 2 + Dust, protection by enclosure, Zone 20, 21/22, 21, 22 FB c-FM-us/c-CSA-us; Gas, encapsulation, Zone 1, 2 (Class I Division 2) + Dust, protection by enclosure, Zone 20, 20/21, 21, 22 (Class II, III Division 1) FR c-FM-us/c-CSA-us; Gas, non-incendive, Class I Division 2 + Dust-ignitionproof, Class II, III Division 1 c = Approved as overfill protection, which can be displayed as; X without W with (WHG, VLAREM) d = Ship approval, which can be displayed as; X without S with (CCS, RINA, NK, ABS, DNV GL, LR, BV) N = Foodstuff / Pharmaceutical certificate, which can be displayed as; X without N with (NSF/ANSI/CAN 61) P with (NIH) F with (FDA, EG1935/2004) f = Thread process side / Cable side, which can be displayed as; F Thread G1 M Thread 1NPT Q Thread R1 g = Cable material / length, which can be displayed as; A PUR / 5m (approx. 16ft) B PUR / 10m (approx. 32ft) H PUR / 15m (appr. 48ft) J PUR / 20m (appr. 64ft) C PUR / 25m (approx. 82ft) D PUR / individually selectable (acc. to CE, RCM, EAC) D PUR / individually selectable (acc. to c-FM-us, c-CSA-us) h = Electronics, which can be displayed as; H Two-wire 4 ... 20 mA/HART W Four-wire Modbus S Three-wire SDI12 i = Sensor setting via smartphone and VEGA Tools app, which can be displayed as; X without B with KEY FOR VEGAPULS 21 / 31 ab = explosion protection, which can be displayed as; XX without, for Ex-free area (CE, UKCA, c-FM-us, c-CSA-us, RCM, EAC) AX without, for Ex-free area (CE, UKCA, RCM) VC ATEX/UKEX/IEC/c-FM-us/c-CSA-us; Gas, intrinsic safety, Zone 0, 0/1, 1, 2 (Class I Division 1, 2) SC EAC/SEPRO; Gas, intrinsic safety; Zone 0, 0/1, 1, 2 TC CCOE/NEPSI/KTL/TIIS; Gas, Intrinsic safety, Zone 0, 0/1, 1, 2 WC INMETRO/IA; Gas, intrinsic safety, Zone 0, 0/1, 1, 2 c = Approved as overfill protection, which can be displayed as; X Without W With (WHG, VLAREM) d = Ship approval, which can be displayed as; X Without S With (CCS, RINA, NK, ABS, DNV GL, LR, BV) N = Foodstuff/Pharmaceutical certificate, which can be displayed as X Without N With (NSF/ANSI/CAN 61) P With (NIH) F With (FDA, EG1935/2004) f = Process fitting, which can be displayed as; G Thread G1½ N Thread 1½NPT R Thread R1½ g = Cable entry / connection, which can be displayed as; M M20x1.5 / Cable gland PA black (ø5-9mm), standard h = Electronics, which can be displayed as; H Two-wire 4 ... 20 mA/HART i = Sensor setting via smartphone and VEGA Tools app X Without B With

Approval Holder:
VEGA Grieshaber KG
Company Name
VEGA Grieshaber KG
Address
Am Hohenstein 113 Schiltach
Postcode
77761
Country
Germany
General Email
info.de@vega.com

View All Listings by this Company
Manufacturer:
VEGA Grieshaber KG
Company Name
VEGA Grieshaber KG
Address
Am Hohenstein 113 Schiltach
Postcode
77761
Country
Germany
General Email
info.de@vega.com

View All Listings by this Company

Print This Approval


#240704008

Concealed, floor mounted basic set with DZR brass body. For use with floor standing combination tap assemblies. Maximum operating pressure 10 bar. Maximum operating temperature 70°C

Section:
1535 Miscellaneous
Section Subtitle:
Tap accessories.
WRAS Approval Number:
240704008
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
½” BSP (F)
Marking:
Hansgrohe & DR
Installation Requirements:
R001 R010
Expiry date:
31/07/2029
Model:
10452180

Approval Holder:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Country
Germany
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company
Manufacturer:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Country
Germany
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company

Print This Approval


#240206701

Range of horizontal or vertical multi-stage pumps with a stainless-steel body (HM models) or cast iron body with blue coloured cationic resin coating (VM models), incorporating either plastic or stainless-steel impellers (see model), stainless steel sleeve, EPDM gaskets and seals. Maximum working pressure 10.0 bar / 16.0 bar (see models). Cold water use only.

Section:
1610 Pumps
Section Subtitle:
Wholesome water use.
WRAS Approval Number:
240206701
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
HM models: 1” - 2” BSP (F) VM models: 1¼” - 1½” BSP (F).
Marking:
Lowara or Goulds Water Technology (both brands of Xylem), manufacturer and address, model number, serial number, maximum working pressure and technical information on adhesive label on body.
Installation Requirements:
R001 R415
Expiry date:
28/02/2029
Model:
1HM, 3HM, 5HM, 10HM, 15HM & 22HM. 1VM, 3VM, 5VM & 10VM. Model nomenclature: W XXX YY Z EM Where: W - flow rate (m3/h), either 1, 3, 5, 10, 15, or 22. XXX - Model type: Horizontal (HM) or Vertical (VM) mode, where last (optional) digit can denote the variable speed drive as follows: Null = standard asynchronous motor, H = equipped with Hydrovar, X = other drives, E = e-SM. YY - Number of impellers/stages HM models: 2-25 stages only (02-25), VM models: 2-8 stages only (02-08). Z - Material, where: (P) is plastic impeller and SS AISI 304 body (HM & VM models), (S) is SS AISI 304 impeller and body (HM models only), (N) is SS AISI 316 impeller and body (HM models only). E = 5 - 6 digits for electrical specification. M = 3 digits, where: 1st digit: Mech. rotary seal - V = Aluminium oxide (Ceramic), or Mech. rotary seal - Q = Silicon carbide (Ceramic). 2nd digit: Mech. stationary seal - B = Carbon resin impregnated. 3rd digit: Mech. seal elastomers - E = EPDM. Example code: 1HM03P05M5HVBE. Max Working Pressure for VM models → 10 bar. Max Working Pressure for HM models with stainless steel impellers and QBE Mechanical Seal → 16 bar (Depending on number of stages - see below), Max Working Pressure for HM models with plastic impellers and/or VBE Mechanical Seal → 10 bar (Depending on number of stages - see below). 1HM (P)/(S)/(N) 1-16 stages - 10.0 bar, 1HM (S)/(N) 18-25 stages - 16.0 bar. 3HM (P)/(S)/(N) 1-13 stages - 10.0 bar, 3HM (S)/(N) 14-21 stages - 16.0 bar. 5HM (P)/(S)/(N) 1-13 stages - 10.0 bar, 5HM (S)/(N) 14-21 stages - 16.0 bar. 10HM (P)/(S)/(N) 1-8 stages - 10.0 bar, 10HM (S)/(N) 9-13 stages - 16.0 bar. 15HM (S)/(N) 2-7 stages - 10.0 bar, 22HM (S)/(N) 2-5 stages - 10.0 bar.

Approval Holder:
Xylem Service Italia S.r.l
Company Name
Xylem Service Italia S.r.l
Address
Via Vittorio Lombardi 14, 36075 Montecchio Maggiore-Alte Ceccato VI, Vicenza
Country
Italy
Phone
0039 0444 707111

View All Listings by this Company
Manufacturer:
Lowara S.r.l | Xylem Service Italia S.r.l | Xylem Manufacturing Middle East Region FZCO Dubai | Xylem Water Systems International Philippines Inc.
Company Name
Lowara S.r.l | Xylem Service Italia S.r.l | Xylem Manufacturing Middle East Region FZCO Dubai | Xylem Water Systems International Philippines Inc.
Address

View All Listings by this Company

Print This Approval


#240602708

Range of single or twin booster pumps with stainless steel bodies and stainless-steel impellers. Maximum working pressure 8.0 Bar Maximum operating temperature 90.0°C

Section:
1610 Pumps
Section Subtitle:
Wholesome water use.
WRAS Approval Number:
240602708
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
1” BSPT F 1 ¼” BSPT F 1 ½” BSPT F
Marking:
EBARA logo, model number with additional technical data on adhesive label on body
Installation Requirements:
R001 R415
Expiry date:
30/06/2029
Model:
1970056704I CDE/I 70/05 IE3 1970096604I CDE/I 70/07 IE3 1980096604I CDE/I 120/07 IE3 1980096614I CDE/I 120/106 220/380-460 IE3 1980206604I CDE/I 120/20 IE3 1970106604I CDE/I 90/10 IE3 1970106804I CDE/I 70/12 IE3 1980106604I CDE/I 120/12 IE3 1990106604I CDE/I 200/12 IE3 1990206604I CDE/I 200/20 IE3 1990256604I CDE/I 200/25 IE3 1970056600E CDME/E 70/05 IE2 1970096600E CDME/E 70/07 IE2 1970106600E CDME/E 70/12 IE2 1970106800E CDME/E 90/10 IE2 1980096600E CDME/E 120/07 IE2 1980106600E CDME/E 120/12 IE2 1980206600E CDME/E 120/20 IE2 1990106600E CDME/E 200/12 IE2 1990206600E CDME/E 200/20 IE2 1610036616I CDXE/I 70/076 220/380-460_60 IE3 1610036716I CDXE/I 70/076 220/380-460_60 SCAIE3 1610056616I CDXE/I 70/106 220/380-460_60 IE3 1610056716I CDXE/I 70/106 220/380-460_60 SCA IE3 1610075216I CDXE/I 70/156 220/380-460_60 1615056604I CDXE/I 70/05 IE3 1615056904I CDXE/I 70/05 SCA IE3 1615096504I CDXE/I 70/07 SCA IE3 1615096604I CDXE/I 70/07 IE3 1615106604I CDXE/I 90/10 IE3 1615109704I CDXE/I 90/10 SCA IE3 1620056616I CDXE/I 120/106 220/380-460_60 IE3 1620056716I CDXE/I 120/106 220/380-460_60 SCA IE3 1610075316I CDXE/I 70/156 220/380-460_60 SCA 1620076616I CDXE/I 120/156 220/380-460_60 1620076716I CDXE/I 120/156 220/380-460_60 SC 1620086516I CDXE/I120/206 220/380-460_60 SCA 1625096604I CDXE/I 120/07 IE3 1625096704I CDXE/I 120/07 SCA IE3 1625106304I CDXE/I 120/12 IE3 SCA 1625106604I CDXE/I 120/12 IE3 1625106904I CDXE/I 120/12 SCA IE3 1625206304I CDXE/I 120/20 IE3 SCA 1625206604I CDXE/I 120/20 IE3 1630076616I CDXE/I 200/156 220/380-460_60 1630086616I CDXE/I 200/206 220/380-460_60 1630086716I CDXE/I200/206 220/380-460_60SCA 1630106616I CDXE/I 200/306 220/380-460_60 1630106716I CDXE/I 200/306 220/380-460_60SCA 1635106604I CDXE/I 200/12 IE3 1635106704I CDXE/I 200/12 SCA IE3 1635206604I CDXE/I 200/20 IE3 1635206704I CDXE/I 200/20 SCA IE3 1635256604I CDXE/I 200/25 IE3 1635256704I CDXE/I 200/25 SCA IE3 1610036610E CDXME/E 70/076 220-230_60 IE2 1610056610E CDXME/E 70/106 220-230_60 IE2 1615057400E CDXME/E 70/05 IE2 1615096600E CDXME/E 70/07 IE2 1615106600E CDXME/E 90/10 IE2 1625096600E CDXME/E 120/07 IE2 1625106600E CDXME/E 120/12 IE2 1625206600E CDXME/E 120/20 IE2 1635106600E CDXME/E 200/12 IE2 1635206600E CDXME/E 200/20 IE2 1611106504I 2CDXE/I 70/10 SCA IE3 1611106510I 2CDXE/I 70/106 220/380-460_60 1611106600E 2CDXEM/E 70/10 IE2 1611106604I 2CDXE/I 70/10 IE3 1611106610I 2CDXE/I 70/106 220/380-460_60 SCA 1611126600E 2CDXEM/E 70/12 IE2 1611126604I 2CDXE/I 70/12 IE3 1611126704I 2CDXE/I 70/12 SCA 1611150200E 2CDXEM/E 70/15 IE2 1611156404I 2CDXE/I 70/15 SCA 1611156604I 2CDXE/I 70/15 IE3 1611206600E 2CDXEM/E 70/20 IE2 1611206604I 2CDXE/I 70/20 IE3 1611206804I 2CDXE/I 70/20 SCA IE3 1619206916I 2CDXE/I70/206 220/380-460_60 SCA 1619207516I 2CDXE/I 70/206 220/380-460_60 1619300214I 2CDXE/I 70/306 220/380-460_60 SCA 1619306614I 2CDXE/I 70/306 220/380-460_60 1621150200E 2CDXEM/E 120/15 IE2 1621156600E 2CDXEM/E 120/15 IE2 1621156604I 2CDXE/I 120/15 IE3 1621159604I 2CDXE/I 120/15 SCA 1621206600E 2CDXEM/E 120/20 IE2 1621206604I 2CDXE/I 120/20 IE3 1621206616I 2CDXE/I 120/206 220/380-460_60 1621206716I 2CDXE/I 120/206 220/380-460_60 SCA 1621209604I 2CDXE/I 120/20 SCA IE3 1989306316I 2CDXE/I 120/306 220/380-460_60 1989306404I 2CDXE/I 120/30 IE3 SCA 1989306604I 2CDXE/I 120/30 IE3 1989306816I 2CDXE/I120/306 220/380-460_60SCA 1989400206I 2CDXE/I 120/406 220/380-460_60 1989400216I 2CDXE/I 120/406 220/380-460_60 SCA 1989406604I 2CDXE/I 120/40 IE3 1989406704I 2CDXE/I 120/40 IE3 SCA 1999306604I 2CDXE/I 200/30 IE3 1999309604I 2CDXE/I 200/30 SCA IE3 1999400206I 2CDXE/I 200/406 220/380-460_60 1999406604I 2CDXE/I 200/40 IE3 1999409604I 2CDXE/I 200/40 SCA IE3 1999500206I 2CDXE/I 200/506 220/380-460_60 1999500216I 2CDXE/I 200/506 220/380-460_60 SCA 1999506604I 2CDXE/I 200/50 IE3 1999509604I 2CDXE/I 200/50 IE3 SCA 1999400216I 2CDXE/I 200/406 220/380_460_60SCA 1611100206E 2CDXME/E 70/106 220-230_60 IE2

Approval Holder:
Ebara Pumps Europe S.p.A.
Company Name
Ebara Pumps Europe S.p.A.
Address
Via Campo Sportivo, 30 – 38023 Cles (TN)
Country
Italy
Phone
0039 444 706 811

View All Listings by this Company
Manufacturer:
Ebara Pumps Europe S.p.A.
Company Name
Ebara Pumps Europe S.p.A.
Address
Via Campo Sportivo, 30 – 38023 Cles (TN)
Country
Italy
Phone
0039 444 706 811

View All Listings by this Company

Print This Approval


#240602035

Range of plastic, stainless steel or brass (see models) shower outlets comprising of a shower handset, shower rails and hose (Models: 58004-46XX and 58004-47XX), a shower handset only (Models: 53401-00XX, 56031-00XX, 53283-04XX, 56565-02XX, 56205-00XX, 56321-20XX and 56183-10XX) or an overhead shower head only (models: 51051-12XX, 54012-31XX, 54112-31XX and 54108-00XX). Models 56565-02XX and 54108-00XX incorporate stainless steel strainers. Maximum operating temperature 60.0°C, open outlet use.

Section:
1650 Shower Outlets
Section Subtitle:
Shower head(s) and/or shower handset(s).
WRAS Approval Number:
240602035
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
½” BSP (M) or (F) (see models)
Marking:
Lota on handset & shower Rail (58004-46XX & 58004-47XX only) Lota on body (all other models)
Installation Requirements:
R001 R040
Expiry date:
30/06/2029
Model:
58004-46XX (Plastic, ½” BSP (F)) 58004-47XX (Plastic, ½” BSP (F)) 53401-00XX (Brass, ½” BSP (M)) 56031-00XX (Plastic, ½” BSP (M)) 53283-04XX (Plastic, ½” BSP (M)) 56565-02XX (Plastic, ½” BSP (M)) 56205-00XX (Plastic, ½” BSP (M)) 56321-20XX (Plastic, ½” BSP (M)) 56183-10XX (Plastic, ½” BSP (M)) 51051-12XX (Plastic, ½” BSP (F)) 54012-31XX (Stainless Steel, ½” BSP (F)) 54112-31XX (Stainless Steel, ½” BSP (F)) 54108-00XX (Stainless Steel, ½” BSP (F)) Where XX denotes the finish and can be replaced with any of the following: 01 = Chrome (All models) 23 = Polished nickel (model 53401-00XX only) 6803 = Matt black (models 56183-10XX & 56321-20XX only)

Approval Holder:
Xiamen Lota International Co., Ltd.
Company Name
Xiamen Lota International Co., Ltd.
Address
No. 61 Xing Nan Road Jimei District Xiamen
Postcode
361022
Country
China
General Email
liwenjuan@lota.com.cn

View All Listings by this Company
Manufacturer:
Xiamen Lota International Co., Ltd.
Company Name
Xiamen Lota International Co., Ltd.
Address
No. 61 Xing Nan Road Jimei District Xiamen
Postcode
361022
Country
China
General Email
liwenjuan@lota.com.cn

View All Listings by this Company

Print This Approval


#240902003

Range of overhead shower outlets, (brass bodies - various finishes. The inlets incorporate combined EPDM washers and stainless-steel strainers. Open outlet use only Maximum operating temperature 60°C

Section:
1650 Shower Outlets
Section Subtitle:
Shower head(s) and/or shower handset(s).
WRAS Approval Number:
240902003
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Note:
Model 27 607 xx0 is supplied with a shower arm Model 27 620 xx0 is supplied with a ceiling connector
Size:
1/2" BSP (M)
Marking:
Hansgrohe on body
Installation Requirements:
R001 R040
Expiry date:
30/09/2029
Model:
27 607 xx0 27 620 xx0 27 623 xx0 Models added February 2025: 27 624 xx0 & 28 821 xx0. Models added September 2025: 33 291 7xx & 32 291 7xx. Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.

Approval Holder:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, Schiltach
Postcode
77761
Country
Germany
Phone
+49 170 4471 718
General Email
Ludovic.hauer@hansgrohe.com

View All Listings by this Company

Print This Approval


#240604004

Self-closing combination tap assembly (chromium plated brass) with a spring-loaded headwork controlling both temperature and flow with a dome type operating member. The spout outlet incorporates a plastic flow straightener. The flexible hose inlets incorporate a combined EPDM washer and stainless-steel strainer, as well as an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.

Section:
1820 Taps
Section Subtitle:
Self closing tap(s).
WRAS Approval Number:
240604004
Size:
Stainless steel or polyamide braided PEX lined flexible hose assemblies incorporating ½” captive nut end connections.
Marking:
Twyford on operating member.
Installation Requirements:
R001 R006 R009 R010
Expiry date:
30/06/2029
Model:
SF2104CP

Approval Holder:
Twyford Geberit Group
Company Name
Twyford Geberit Group
Address
Geberit House, Edgehill Drive, Warwick
Postcode
CV34 6NH
Country
United Kingdom
Phone
01926 516800
General Email
enquiries@geberit.co.uk

View All Listings by this Company

Print This Approval


#240702054

Self-closing pillar tap (chromium plated brass) with spring loaded headwork and dome operating member. The spout outlet incorporates a plastic aerator. Supplied with brass backnuts. Maximum working pressure 10 Bar Maximum operating temperature 85°C

Section:
1820 Taps
Section Subtitle:
Self closing tap(s).
WRAS Approval Number:
240702054
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
½” BSP (M)
Marking:
Armitage shanks on operating member.
Installation Requirements:
R001 R005
Expiry date:
31/07/2029
Model:
B8267AA – Avon 21

Approval Holder:
Armitage Shanks
Company Name
Armitage Shanks
Address
Old Road (Lodge 1), Armitage, Rugeley
Postcode
WS15 4BT
Country
Staffordshire,
Phone
+44 800 866 966 Fax: 01543 491677 Telex: 339781

View All Listings by this Company

Print This Approval


#240902016

Self-closing, wall mounted bib tap (chromium plated brass) with spring loaded headwork and dome type operating members. The spout outlet incorporates a plastic aerator with integral flow regulator or optional flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.

Section:
1820 Taps
Section Subtitle:
Self closing tap(s).
WRAS Approval Number:
240902016
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
½” BSP M
Marking:
Armitage Shanks on operating member
Installation Requirements:
R001 R040
Expiry date:
30/09/2029
Model:
S7241AA Avon 21

Approval Holder:
Armitage Shanks
Company Name
Armitage Shanks
Address
Old Road (Lodge 1), Armitage, Rugeley
Postcode
WS15 4BT
Country
Staffordshire,
Phone
+44 800 866 966 Fax: 01543 491677 Telex: 339781

View All Listings by this Company

Print This Approval


#240202085

Range of stainless-steel braided EPDM lined flexible hose assemblies with EPDM seals, available with a variety of end connections, some of which include isolation valves (see model). Maximum working pressure 10 Bar. Maximum operating temperature 85°C

Section:
1863 Tubes
Section Subtitle:
Elastomeric.
WRAS Approval Number:
240202085
Size:
See Models
Marking:
MF, WRAS and Date of manufacture (YYYY) on ferrule.
Installation Requirements:
R001
Expiry date:
28/02/2029
Model:
MFLEXTC150330, 30cm length MFLEXTC150415, 15cm length MFLEXTC150430, 30cm length MFLEXTC150450, 50cm length MFLEXTC150490, 90cm length MFLEXTC150630, 30cm length MFLEXTC150650, 50cm length MFLEXTC150690, 60cm length MFLEXTC220630, 30cm length MFLEXTC220650, 50cm length MFLEXTC220690, 90cm length MFLEXTC151530, 30cm length MFLEXTC151550, 50cm length MFLEXTC151590, 90cm length MFLEXTC222230, 30cm length MFLEXTC222250, 50cm length MFLEXTC150430M, 30cm length MFLEXTC1504V MFLEXTC1506V MFLEXTC2206V MFLEXTC150415V, 15cm length MFLEXTC1510450V, 50cm length MFLEXTC1510650V, 50cm length MFLEXMTC1004 (suit, Set of 2 type) MFLEXMTC100450, 50cm length(suit, Set of 2 type) MFLEXMTC1204 (suit, Set of 2 type) MFLEXMTC120450 (suit, Set of 2 type) MFLEXMTC1015 (suit, Set of 2 type) MFLEXMTC101550, 50cm length(suit, Set of 2 type) MFLEXMTC1215 (suit, Set of 2 type) MFLEXMTC121550, 50cm length(suit, Set of 2 type) MFLEXTC040430, 30cm length MFLEXTC040450, 50cm length DN8 GMF0813S - M10 short male x 3/8"F captive nut GMF0813L - M10 Long male x 3/8"F captive nut GMF0815S - M10 short male x 1/2"F captive nut GMF0815L - M10 Long male x 1/2"F captive nut GMF0803S - M8 short male x 3/8"F captive nut GMF0823S - M12 short male x 3/8"F captive nut GMF0823L - M12 Long male x 3/8"F captive nut GMF0825S - M12 short male x 1/2"F captive nut GMF0825L - M12 Long male x 1/2"F captive nut DN10 GMF1013S - M10 short male x 3/8"F captive nut GMF1013L - M10 Long male x 3/8"F captive nut GMF1015S - M10 short male x 1/2"F captive nut GMF1015L - M10 Long male x 1/2"F captive nut GMF1023S - M12 short male x 3/8"F captive nut GMF1023L - M12 Long male x 3/8"F captive nut GMF1025S - M12 short male x 1/2"F captive nut GMF1025L - M12 Long male x 1/2"F captive nut DN13 GMF1313S - M10 short male x 3/8"F captive nut GMF1313L - M10 Long male x 3/8"F captive nut GMF1315S - M10 short male x 1/2"F captive nut GMF1315L - M10 Long male x 1/2"F captive nut GMF1323S - M12 short male x 3/8"F captive nut GMF1323L - M12 Long male x 3/8"F captive nut GMF1325S - M12 short male x 1/2"F captive nut GMF1325L - M12 Long male x 1/2"F captive nut GAN series DN8 GAN0833 - 3/8"F x 3/8"F captive nut GAN0835 - 3/8"F x 1/2"F captive nut GAN0855 - 1/2"F x 1/2"F captive nut GAN0877 - 3/4"F x 3/4"F captive nut GAN0857 - 1/2"F x 3/4"F captive nut DN10 GAN1033 - 3/8"F x 3/8"F captive nut GAN1055 - 1/2"F x 1/2"F captive nut GAN1077 - 3/4"F x 3/4"F captive nut DN13 GAN1333 - 3/8"F x 3/8"F captive nut GAN1355 - 1/2"F x 1/2"F captive nut GAN1377 - 3/4"F x 3/4"F captive nut GAM series DN8 GAM0833 - 3/8"M x 3/8"F captive nut GAM0835 - 3/8"M x 1/2"F captive nut GAM0853 - 1/2"M x 3/8"F captive nut GAM0855 - 1/2"M x 1/2"F captive nut GAM0877 - 3/4"M x 3/4"F captive nut DN10 GAM1033 - 3/8"M x 3/8"F captive nut GAM1035 - 3/8"M x 1/2"F captive nut GAM1053 - 1/2"M x 3/8"F captive nut GAM1055 - 1/2"M x 1/2"F captive nut GAM1077 - 3/4"M x 3/4"F captive nut DN13 GAM1333 - 3/8"M x 3/8"F captive nut GAM1335 - 3/8"M x 1/2"F captive nut GAM1353 - 1/2"M x 3/8"F captive nut GAM1355 - 1/2"M x 1/2"F captive nut GAM1377 - 3/4"M x 3/4"F captive nut GMM series DN8 GMM0833 - 3/8"M x 3/8"M GMM0855 - 1/2"M x 1/2"M DN10 GMM1033 - 3/8"M x 3/8"M GMM1055 - 1/2"M x 1/2"M GMM1055 - 1/2"M x 1/2"M DN13 GMM1355 - 1/2"M x 1/2"M GMM1377 - 3/4"M x 3/4"M GEF series DN8 GEF0833 - 3/8"Elbow F x 3/8"F GEF0835 - 3/8"Elbow F x 1/2"F GEF0853 - 1/2"Elbow F x 3/8"F GEF0855 - 1/2"Elbow F x 1/2"F DN10 GEF1055 - 1/2"Elbow F x 1/2"F GEF1057 - 1/2"Elbow F x 3/4"F GEF1077 - 3/4"Elbow F x 3/4"F DN13 GEF1355 - 1/2"Elbow F x 1/2"F GEF1357 - 1/2"Elbow F x 3/4"F GEF1377 - 3/4"Elbow F x 3/4"F GEM series DN8 GEM0833 - 3/8"Elbow F x 3/8"M GEM0835 - 3/8"Elbow F x 1/2"M GEM0853 - 1/2"Elbow F x 3/8"M GEM0855 - 1/2"Elbow F x 1/2"M DN10 GEM1055 - 1/2"Elbow F x 1/2"M GEM1057 - 1/2"Elbow F x 3/4"M GEM1077 - 3/4"Elbow F x 3/4"M DN13 GEM1355 - 1/2"Elbow F x 1/2"M GEM1357 - 1/2"Elbow F x 3/4"M GEM1377 - 3/4"Elbow F x 3/4"M GMC series DN8 GMC0815S - M10 short male x 15mm compression GMC0815L - M10 Long male x 15mm compression GMC0825S - M12 short male x 15mm compression GMC0825L - M12 Long male x 15mm compression DN10 GMC1015S - M10 short male x 15mm compression GMC1015L - M10 Long male x 15mm compression GMC1025S - M12 short male x 15mm compression GMC1025L - M12 Long male x 15mm compression DN13 GMC1315S - M10 short male x 15mm compression GMC1315L - M10 Long male x 15mm compression GMC1325S - M12 short male x 15mm compression GMC1325L - M12 Long male x 15mm compression GAC series DN8 GAC0855 - 15mm compression x 1/2"F captive nut GAC0857 - 15mm compression x 3/4"F captive nut GAC0877 - 22mm compression x 3/4"F captive nut DN10 GAC1053 - 15mm compression x 3/8"F captive nut GAC1055 - 15mm compression x 1/2"F captive nut GAC1057 - 15mm compression x 3/4"F captive nut GAC1077 - 22mm compression x 3/4"F captive nut DN13 GAC1355 - 15mm compression x 1/2"F captive nut GAC1357 - 15mm compression x 3/4"F captive nut GAC1377 - 22mm compression x 3/4"F captive nut GAC1977 - DN19 22mm compression x 3/4"F captive nut GVF series DN8 GVF0855 - 15mm isolating valve x 1/2"F captive nut GVF0877 - 22mm isolating valve x 3/4"F captive nut DN10 GVF1055 - 15mm isolating valve x 1/2"F captive nut GVF1057 - 15mm isolating valve x 3/4"F captive nut GVF1077 - 22mm isolating valve x 3/4"F captive nut DN13 GVF1355 - 15mm isolating valve x 1/2"F captive nut GVF1377 - 22mm isolating valve x 3/4"F captive nut GVF1977 - DN19 22mm isolating valve x 3/4"F captive nut GDC series DN8 GDC0855 - 15mm compression x 15mm compression GDC0877 - 22mm compression x 22mm compression DN GDC1055 - 15mm compression x 15mm compression GDC1077 - 22mm compression x 22mm compression DN13 GDC1355 - 15mm compression x 15mm compression GDC1377 - 22mm compression x 22mm compression DN19 GDC1977 - 22mm compression x 22mm compression GDEF series DN13 GDEF1355 - 1/2"Elbow F x 1/2"Elbow F

Approval Holder:
Masterflow Products Limited
Company Name
Masterflow Products Limited
Address
Globall House 95 Vantage Point West Mindlands
Postcode
DY6 7FT
Country
United Kingdom

View All Listings by this Company

Print This Approval


#240202092

Range of stainless-steel braided EPDM lined flexible hose assemblies with EPDM seals, available with a variety of end connections, some of which include isolation valves (see model). Maximum working pressure 10 Bar. Maximum operating temperature 85°C

Section:
1863 Tubes
Section Subtitle:
Elastomeric.
WRAS Approval Number:
240202092
Size:
See Models
Marking:
Brymec, Size, PN, WRAS and Date of manufacture (YYYY) on ferrule.
Installation Requirements:
R001
Expiry date:
28/02/2029
Model:
DN10 30909 50cm length & 30925 30cm length - 15mm compression x 1/2"F captive nut 30911 50cm length & 30917 30cm length - 15mm compression x 3/4"F captive nut DN13 30904 50cm length & 30913 30cm length - 15mm compression x 1/2"F captive nut 30927 15mm compression x 3/4"F captive nut 30942 50cm length & 30928 30cm length - 22mm compression x 3/4"F captive nut 30903 DN19 22mm compression x 3/4"F captive nut DN10 30924 - 15mm isolating valve x 1/2"F captive nut DN13 30921- 22mm isolating valve x 3/4"F captive nut 30934 50cm length & 30926 30cm length - 15mm compression x 15mm compression DN13 30945 50cm length & 30932 30cm length- 22mm compression x 22mm compression

Approval Holder:
Brymec Ltd
Company Name
Brymec Ltd
Address
Redlands , Coulsdon, Surrey
Postcode
CR5 2HT
Country
United Kingdom
General Email
Jeremy.douglas@brymec.com

View All Listings by this Company

Print This Approval


#240902006

Stainless steel interlocked (chrome plated) silicone lined kitchen tap pull-out hose. Open outlet use only. Maximum operating temperature 85°C.

Section:
1863 Tubes
Section Subtitle:
Elastomeric.
WRAS Approval Number:
240902006
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
M12 x M12.
Marking:
Dornbracht on ferule.
Installation Requirements:
R001
Expiry date:
30/09/2029
Model:
04300212000

Approval Holder:
Dornbracht GmbH & Co. KG.
Company Name
Dornbracht GmbH & Co. KG.
Address
Koebbingser Muehle 6 Iserlohn
Postcode
D-58640
Country
Germany
Phone
+49 2371 433 0
General Email
wpape@dornbracht.com

View All Listings by this Company

Print This Approval


#240702012

Range of T-type thermostatic blending valves with DZR brass bodies (various finishes). Compression inlets incorporate a stainless-steel strainer and check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Push-fit inlets incorporate a check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. HEAT112050 & HEAT112055 models incorporate angled inlets with integral spherical valves. HEAT112010, HEAT112015, HEAT112050, HEAT112055 – Compression for use with copper pipe (to BSEN1057:2006) only. HEAT155001, HEAT155010 – Push fit for use with PEX pipe (to BS7291 part 3), Polybutylene pipe (to BS7291 part 2) & Copper pipe (to BSEN1057:2006). Maximum working pressure 10.0 bar at 20°C and 7.0 bar at 85°C.

Section:
2010 Shower Valves
Section Subtitle:
Shower valve(s) with thermostatic temperature control
WRAS Approval Number:
240702012
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Note:
R010 applies to push-fit models only
Size:
Please refer to models.
Marking:
RWC logo, TMV and easyfit on cap. Date of manufacture (DWWYYLL), Flow arrow CR and H+ C on body. Models added January 2025: RWC logo on cap. CR, date of manufacture (D/WW/YY/LL), flow arrow and H+C on body
Installation Requirements:
R001 R010 R040
Expiry date:
31/07/2029
Model:
HEAT112 SERIES: HEAT112010: EASIFIT TMV 15MM 2: 1 COMPRESSION. HEAT112015: EASIFIT TMV 22MM 2: 1 COMPRESSION. HEAT112050: EASIFIT TMV 15MM 4: 1 COMPRESSION. HEAT112055: EASIFIT TMV 22MM 4: 1 COMPRESSION. HEAT155 SERIES: HEAT155001: EASIFIT TMV 12MM 2: 1 PUSH FIT. HEAT155010: EASIFIT TMV 15MM 2: 1 PUSH FIT. Models added May 2025: HEAT112100 ½” BSP M. HEAT112110 ¾” BSP M.

Approval Holder:
Reliance Worldwide Corporation (UK)
Company Name
Reliance Worldwide Corporation (UK)
Address
Horton Road, West Drayton
Postcode
UB7 8JL
Country
United Kingdom
Phone
+44 7730 052060
General Email
PETER.LANCASTER@RWC.COM

View All Listings by this Company
Manufacturer:
Reliance Worldwide Corporation (UK)
Company Name
Reliance Worldwide Corporation (UK)
Address
Horton Road, West Drayton
Postcode
UB7 8JL
Country
United Kingdom
Phone
+44 7730 052060
General Email
PETER.LANCASTER@RWC.COM

View All Listings by this Company

Print This Approval


#240702040

Range of wall mounted, thermostatic shower valves (chromium plated brass) incorporating a single sequential headwork controlling both flow and temperature with a single lever operating member. The inlets incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection The product is supplied with an isolation valve for each inlet. Maximum working pressure; 10 Bar Maximum operating temperature 85°C

Section:
2010 Shower Valves
Section Subtitle:
Shower valve(s) with thermostatic temperature control
WRAS Approval Number:
240702040
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
1/2" BSP (M)
Marking:
Armitage Shanks on body.
Installation Requirements:
R001 R010 R040
Expiry date:
31/07/2029
Model:
A4130AA - Contour 21

Approval Holder:
Armitage Shanks
Company Name
Armitage Shanks
Address
Old Road (Lodge 1), Armitage, Rugeley
Postcode
WS15 4BT
Country
Staffordshire,
Phone
+44 800 866 966 Fax: 01543 491677 Telex: 339781

View All Listings by this Company

Print This Approval


#240702055

Range of wall mounted thermostatic shower valves (chromium plated brass bodies). Flow is controlled by a quarter turn ceramic disc headwork with dome operating member and temperature is controlled independently via a thermostatic cartridge with dome type operating member. The inlets incorporate a single check valve cartridge however, the complete assembly has not been fully tested to demonstrate that it provides backflow protection Maximum working pressure 10 bar. Maximum operating temperature 60°C.

Section:
2010 Shower Valves
Section Subtitle:
Shower valve(s) with thermostatic temperature control
WRAS Approval Number:
240702055
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
15mm compression.
Marking:
Ideal standard on body.
Installation Requirements:
R001 R010 R040
Expiry date:
31/07/2029
Model:
A7202AA Ceratherm T25. A7216AA Ceratherm T50. A7231AA Ceratherm T100.

Approval Holder:
Ideal Standard (UK) Ltd
Company Name
Ideal Standard (UK) Ltd
Address
Old Road (Lodge 1) Armitage, Rugeley, Staffordshire
Postcode
WS15 4BT
Country
United Kingdom
General Email
tyeomans@idealstandard.co.uk

View All Listings by this Company

Print This Approval


#2310164

Range of pilot operated pressure reducing valves with blue epoxy coated ductile iron bodies. The valves have an adjustable pressure reducing facility controlled via a pilot valve (with an operating range of 1 to 6 bar), with auxiliary components including stainless steel tubing, fittings and spherical valves. Maximum working pressure 16.0 bar. Maximum operating temperature 23°C.

Section:
2205 Valves
Section Subtitle:
Pressure reducing, pilot operated.
WRAS Approval Number:
2310164
Size:
DN50, DN65, DN80, DN100, DN125, DN150, DN200, DN250 & DN300 flanged inlets and outlets.
Marking:
Maplef, PN & DN on dataplate.
Installation Requirements:
R001
Expiry date:
31/10/2028
Model:
MV80-211 Range

Approval Holder:
Maplef Valves and Fittings Ltd
Company Name
Maplef Valves and Fittings Ltd
Address
Suite 1488 1130 West Pender St Vancouver, BC, V6E 4A4
Country
Canada
Phone
001 604 770 2440
General Email
s.aljaf@maplefgeneralsupplier.ca

View All Listings by this Company

Print This Approval


#240102089

Range of lever or butterfly operated spherical valves with brass or nickel plate bodies and ball. Maximum working pressure 40.0 Bar Maximum operating temperature 99.0°C

Section:
2260 Valves
Section Subtitle:
Spherical valve(s) with metal body
WRAS Approval Number:
240102089
Size:
See models – All models BSP (F) x (F)
Marking:
MF, DN, PN & Size on body.
Installation Requirements:
R001
Expiry date:
31/01/2029
Model:
40.0 Bar: FF617 -0025: ¼”. G or RC thread FF617 -0038: ⅜”. G or RC thread FF617 -0050: ½”. G or RC thread FF617 -0075: ¾”. G or RC thread FF617 -0100: 1”. G or RC thread FF617 -0125: 1¼ ”. G or RC thread FF617 -0150: 1½ ”. G or RC thread FF617 -0200: 2”. G or RC thread M44020200: ¼”. G or RC thread M44030300: ⅜”. G or RC thread M44040400: ½”. G or RC thread M44060600: ¾”. G or RC thread M44080800: 1”. G or RC thread M44101000: 1¼ ”. G or RC thread M44121200: 1½ ”. G or RC thread M44161600: 2”. G or RC thread

Approval Holder:
Masterflow Products Limited
Company Name
Masterflow Products Limited
Address
Globall House 95 Vantage Point West Mindlands
Postcode
DY6 7FT
Country
United Kingdom

View All Listings by this Company

Print This Approval


#240602022

Range of spherical valves with stainless steel bodies, incorporating PTFE seats and a lever t operating member. Maximum working pressure: 68 Bar. Maximum operating temperature: 100°C

Section:
2260 Valves
Section Subtitle:
Spherical valve(s) with metal body
WRAS Approval Number:
240602022
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
1/4" to 1" Threaded End (F-F) (see models)
Marking:
Super inox logo, Cf8m, pressure, temperature, size and year of manufacture (YYYY) on body
Installation Requirements:
R001
Expiry date:
30/06/2029
Model:
S2108 (1/4”) S2110 (3/8”) S2115 (1/2”) S2015 (1/2”) S2120 (3/4”) S2020 (3/4”) S2125 (1”)

Approval Holder:
SUPER INOX CORPORATION
Company Name
SUPER INOX CORPORATION
Address
No.7, Alley 131, Lane 431, Sec.2 MeiGao Road YangMei Dist TaoYuan
Postcode
32647
Country
Taiwan
Phone
886-3-2115015
General Email
inox@ms16.hinet.net

View All Listings by this Company
Manufacturer:
SUPER INOX CORPORATION
Company Name
SUPER INOX CORPORATION
Address
No.7, Alley 131, Lane 431, Sec.2 MeiGao Road YangMei Dist TaoYuan
Postcode
32647
Country
Taiwan
Phone
886-3-2115015
General Email
inox@ms16.hinet.net

View All Listings by this Company

Print This Approval


#2204108

Range of quarter turn, lever handle or butterfly operated spherical valves with nickel plated brass bodies, chrome plated brass balls and PTFE seals. For use with copper pipe BS EN 1057. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.

Section:
2260 Valves
Section Subtitle:
Spherical valve(s) with metal body
WRAS Approval Number:
2204108
Size:
SEE MODELS
Marking:
PFP, size, date of manufacture (MM/YY) on body. ON/OFF, size and WRAS on lever.
Installation Requirements:
R001
Expiry date:
30/04/2027
Model:
Red butterfly handle circlip reduced bore ball valve models: 10055815 15MM 10055822 22MM Red handle circlip full bore ball valve models: 10055404 15MM 10055413 22MM 10055422 28MM Red handle circlip full bore ball valve bright models: 10055431 35MM 10055440 42MM 10055449 54MM Blue handle circlip full bore ball valve models: 10055605 15MM 10055612 22MM 10055619 28MM Blue handle circlip full bore ball valve bright models: 10055626 35MM 10055633 42MM 10055640 54MM Red handle full bore ball valve with internal thread models: 10055300 1/4" BSP (F) 10055307 3/8" BSP (F) 100553141/2" BSP (F) 10055321 3/4" BSP (F) 10055328 1" BSP (F) 10055335 1 1/4" BSP (F) 10055342 1 1/2" BSP (F) 10055349 2" BSP (F) Blue handle full bore ball valve with internal thread models: 10055501 1/2" BSP (F) 10055508 3/4" BSP (F) 10055515 1" BSP (F) 10055522 1 1/4" BSP (F) 10055529 1 1/2" BSP (F) 10055536 2" BSP (F)

Approval Holder:
Primaflow F & P
Company Name
Primaflow F & P
Address
Votec House, Hambridge Lane, Newbury
Postcode
RG14 5TN
Country
United Kingdom

View All Listings by this Company

Print This Approval



Back To Directory Sections

Page 127 of 160

We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.