'HEMPADUR 35600 Cream and Red'. Factory applied, cream or red coloured (when mixed), two-component epoxy coatings consisting of a base and curing agent. Mix the base and curing agent in a 14.8:5.2 volume ratio. Cure for 8 days@25°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`Jin Dapeng WEY-Black, WEY-Red & WEY-Blue`. Factory applied epoxy coatings. Apply and cure as per manufacturer's instructions 'version no: JDP2015-01' dated 24th November 2015. For use with water up to 85°C.
'Ever-Blue'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's TDS '20200801 A1'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Intercrete 4807'. Site applied, grey coloured cementitious repair mortar. Mix 'Intercrete 4807' and water in a mass ratio of 9.4:1 Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`Fernox Powerflow Flux`. White coloured paste flux. For use with water up to 85°C.
'IKV Tribostar SSI 1203TF/IKV Tribofood SSI 1203TF'. Translucent, white coloured silicone greases. Apply as per manufacturer's instructions. For use with water up to 85°C.
'Grasso L. 100 Lubricating Grease'. White coloured grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
'Bluesil Paste 408'. White coloured, translucent silicone paste lubricant. Apply as per manufacturer's instructions. For use with water up to 85°C.
'Celanyl A3 WR GF30 BK 9005/Z/FA'. Black coloured, injection moulded PA material. For use with water up to 85°C.
'PA66+50%GF 1620G50 BK015'. Black coloured, injection moulded PA66 (with 50% glass fibre) material. For use with water up to 85°C.
'MMP PE100 Pipe'. Black coloured (with blue coloured external stripes), extruded PE100 pipes manufactured from 'Sabic P6006' or 'Borouge HE3490-LS'. For use with water up to 85°C.
'Unidelta Flexall'. Extruded, PE-RT/Al/PE-RT pipe comprising of white coloured (translucent) inner layer, aluminum middle later and white coloured (opaque) outer layer. For use with water up to 85°C.
'TP10847 Prisma Black'. Black coloured polyethylene material manufacture by rotational moulding. For use with water up to 70°C.
`Revolve N-525 (6056) Natural (appears white coloured) & BH3239 Black (black coloured)`. Polyethylene materials manufactured by rotational moulding. For use with water up to 85°C.
`Revolve N-650/6068 Natural (appears cream coloured) & M-668 Black (black coloured)`. Polyethylene materials manufactured by rotational moulding. For use with water up to 85°C.
'Revolve 6405U Natural (appears white coloured) & Revolve M-1585 Black (black coloured)'. Polyethylene materials manufactured by rotational moulding. For use with water up to 85°C.
‘Revolve N-840 (HD3850) & Revolve M-750 DR Black’. Revolve N-840 (HD3850) is a white coloured polyethylene material & Revolve M-750 DR Black is a black coloured polyethylene material. Both are manufactured by rotational moulding. For use with water up to 85°C. Please note that ‘Revolve N-840 (HD3850)’ was formerly known as ‘Revolve N-840 (6850)’.
'Revolve N-307 Boat Blue M2-018D'. Blue coloured polyethylene material manufactured by rotational moulding. For use with water up to 85°C.
'XYRON WG732 AWY2266, WG732 AWY2269, WG732 AWY6628, WG722 AWY6627, W5002 AWY1208, W5002 AWY2267, W5002 AWY6629, W5002 AWY3326, WG722 AWY2261, WG732 AWY3325, WG722 AWY3324 & WG733 ABY3315'. Injection moulded, black, grey or beige coloured PPE materials manufactured in Thailand & China. For use with water up to 85°C.
‘Tecomid HT NT40 GR30 BK009 01 QW, Tecomid HT NT40 GR35 BK009 01 QW, Tecomid HT NT40 GR40 BK009 01 QW, Tecomid HT NT40 GR45 BK009 01 QW, Tecomid HT NT40 GR50 BK009 01 QW, Tecomid HT NT40 GR55 BK009 01 QW & Tecomid HT NT40 GR60 BK009 01 QW’. Black coloured, injection moulded glass-fibre reinforced PPA materials. For use with water up to 85°C.
'DACTAtherm PP-R 80 Green Pipe'. Green coloured, extruded polypropylene pipe. For use with water up to 85°C.
'G310'. Blue coloured, extruded PTFE material. For use with water up to 85°C.
`USW-85`. Black coloured, injection moulded TPU material. For use with water up to 23°C.
'Qmonix® 558CH'. Black coloured, transfer moulded, EPDM 'O' rings. Shore hardness 70. Tested in-radius size 0.85mm. For use with water up to 85°C.
‘PX70N-0201 washers, ‘O’ rings, bushes gaskets & discs’. Black coloured, injection moulded EPDM components with a shore hardness of 70. The washers have a tested in-radius size of 3.0mm. The ‘O’ rings have a tested in-radius size of 3.5mm. The bushes gaskets have a tested in-radius size of 2.0mm. The discs have a tested in-radius size of 2.65mm. All are for use with water up to 85°C.
'EPDM4570‐70/Jinan Hongde Gasket Material'. Black coloured, compression moulded EPDM sheet material. Shore hardness 70. Tested in-radius 2.0mm. For use with water up to 85°C.
'EPDMprx'. Black coloured, injection moulded EPDM material. Shore hardness 78. Tested in-radius size 1.0mm. For use with water up to 85°C.
'60 EPDM 334 black 60 ShA' (shore hardness 60) and '70 EPDM 335 black 70 ShA' (shore hardness 70). Black coloured compression moulded EPDM materials. Tested in-radius 1.07mm. For use with water up to 85°C.
'01/T60FKM, 01/T70FKM & 01/T80FKM 'O' rings and gaskets'. Green coloured, injection moulded FKM 'O' rings and gaskets. Shore hardness between 60 & 80. 'O' rings have a tested in-radii size of between 2.0mm & 3.5mm. Gaskets have a tested in-radii size of between 2.5mm & 3.5mm. For use with water up to 23°C.
‘SuraSil GP40 - SuraSil GP70’. Extruded silicone rubber components available in translucent, blue, white, red & black colours. Shore hardness between 40 & 70. The components and their tested in-radii sizes are; Tubes - in-radii between 0.77mm & 4.81mm. Cords - in-radii between 0.5mm & 18.07mm. Strips - in-radii between 1.0mm & 5.23mm. Profiles - in-radii between 1.0mm & 13.00mm. Squares - in radii between 1.0mm & 15.38mm. For use with water up to 85°C.
‘ELASTOSIL® R plus 4303/60 mH (60), ELASTOSIL® R plus 4303/70 mH (70) and ELASTOSIL® R plus 4303/80 mH (80)’. Extruded, natural (appears white in colour) platinum cured HTV silicone rubber with a shore hardness of between 60 & 80. Tested in-radius size 2.0mm. The rubbers may also be coloured using the following ELASTOSIL® Color Pastes PT in a maximum of 1% content: PT Carbon black RAL 9005. PT Red brown RAL 3013. PT Red RAL 3000 F. PT Yellow RAL1016 PT Yellow RAL 1026 F PT Yellow RAL 1021. PT Grey RAL 7040. PT Dark blue 5010. PT Ultramarine blue RAL 5002. PT Violet RAL 4001. PT Green RAL 6017. PT Black RAL 9017. PT White RAL 9010. PT Yellow RAL 1033. PT Orange RAL 2004 F. PT Violet RAL 4002. PT Blue RAL 5022. PT Helio green RAL 6004. For use with water up to 85°C.
'Bondchem WS27'. Anaerobic adhesive which is available in a yellow colour or in a yellow/orange colour. Apply as per manufacturer's instructions and cure for 15 minutes@25°C or 24 hours@22°C. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions.
Floor mounted, single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with single lever operating member and a lockable diverter to shower outlet. The spout outlet incorporates a plastic aerator. The product is supplied with a shower hose and handset. Both the shower outlet (from the main body) and the inlet to the shower handset incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) electronically operated tap assemblies incorporating brass bodies (various finishes). Flow is controlled via solenoid valve and actuated by a touch sensor. The hose inlet incorporates a flow restrictor and the spout outlets incorporate a plastic aerator. Maximum working pressure 7.5 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (various finishes) with a pull-out spray mechanism. Flow is controlled via a ceramic cartridge headwork with a single lever operating member incorporating an infra-red sensor on the swivel arm which operates a solenoid valve. The spout outlet incorporates a plastic aerator and a hand spray mechanism, and the product is supplied with metal backnuts. Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C.
Bottom entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. The inlet incorporates a flow restrictor. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a vertical BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a pneumatically operated dual flush outlet valve. The flush volume is operated by a two push button assembly for a 6 or 3 litre flush volume. The inlet supply incorporates a servicing valve. For use with cold water only. Maximum working pressure 10.0 bar.
Concealed WC dual flushing cistern with a vertical BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a pneumatically operated dual flush outlet valve. The flush volume is operated by a two push button assembly for a 6 or 3 litre flush volume. The inlet supply incorporates a servicing valve. Maximum working pressure 10.0 bar. Cold water use only.
Range of concealed cisterns incorporating a side entry float operated inlet valve providing a type AC air gap arrangement and a dual flush outlet valve. Maximum working pressure 10.0 Bar. Cold water use only.
BS EN 14055: 2018 concealed WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AB air gap and lever operated syphon capable of full flush volumes of up to 6 litres and reduced flush of up to 4 litres. Maximum working pressure 10.0 bar. Cold water use only.
Range of non-verifiable double check valve assemblies with DZR brass bodies, incorporating two spring loaded, resilient trim in-line check valve cartridges. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headwork incorporating plastic bodies (various finishes) and NBR ‘O’-rings. The products are intended for insertion into specifically dimensioned tap assemblies. Maximum working pressure 12.0 bar. Maximum operating temperature 85°C.
Ceramic cartridge headwork with a plastic body, silicone gaskets and seals. For insertion into specifically dimensioned tap bodies. Maximum working pressure 10.0 bar. Maximum working temperature 85°C.
Thermostatic cartridge incorporating brass bodies and stainless steel filters. For insertion into specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of thermostatic cartridges incorporating brass bodies, stainless steel strainers and EPDM ‘O’-rings. For insertion into specifically dimensioned tap bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of thermostatic cartridges with plastic bodies, stainless steel strainers and NBR ‘O’-rings. For insertion into specifically dimensioned bodies. Maximum operating temperature 85°C.
Range of single hole, single outlet (swivel) combination tap assemblies (various finishes) with ceramic cartridge headworks and single lever operating members. The spout outlet incorporates a pull-out spray with plastic aerator. The cold Inlet incorporates approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating pressure 5.0 bar. Maximum operating temperature 60°C.
Range of deck mounted combination tap assemblies (chromium plated brass) incorporating rising spindle headwork with single lever operating members, swivel spout outlet and separate pull-down spray outlet (with self-closing trigger assembly). The spout outlets incorporate a plastic flow straightener and the products are supplied with metal backnuts. Models 98008-M001 & 98008-1 are single hole, single outlet. Model 98007-1 is two-hole, single outlet. Model 98001-2 is single hole, double outlet. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of wall mounted combination tap assemblies (chromium plated brass) incorporating rising spindle headwork with single lever operating members, swivel spout outlet and separate pull-down spray outlet (with self-closing trigger assembly). The spout outlets incorporate a plastic flow straightener and the products are supplied with metal backnuts. Model 98011-1 is single hole, single outlet. Models 98002-1 & 98002-M001 are two-hole, single outlet. Model 98002MN-2 is two-hole, double outlet. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlet incorporates a plastic aerator. The product is supplied with a click type waste. Maximum working pressure 5.0 bar. Maximum operating temperature 70°C.
Page 11 of 158
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
