'PPA-GF10-NC' (natural, appears yellow-green) & 'PPA-GF10-BK' (black coloured). Injection moulded PPA materials. For use with water up to 85°C.
'122102251 PP Mechanical Fitting'. Black coloured, injection moulded, polypropylene compression fitting body. For use with water up to 23°C.
'RRS 502B GR1500'. In February 2025, ‘RRA 410B GR1500’ was added to the approval. Dark grey coloured, injection moulded PVC materials. For use with water up to 23°C.
'Chemfix CH+ MAX'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions dated 18/05/2022. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ME FGL 75D'. Black coloured, ebonite material manufactured by calendaring and autoclave curing. Shore hardness 75. Tested in-radius size 1.75mm. For use with water up to 23°C.
'E24 EPDM moulded parts.' Black coloured, injection moulded EPDM seals. Shore hardness 75. Type 1 moulded seals have a tested in-radius size of 4.2mm and Type 2 moulded seals have a tested in-radius size of 0.7mm. For use with water up to 85°C.
'01/U70EP 'O' ring' with a tested in-radius size between 0.5mm & 3.5mm. In June 2024, the follow components were added to the approval: ‘01/U70EP Cylindrical Gasket’ with a tested in-radius size between 0.9mm & 1.25mm. ‘01/U70EP Membrane’ with a tested in-radius size between 2.1mm & 5.5mm. Black coloured, injection moulded EPDM components. Shore hardness 70 For use with water up to 85°C.
'01/U80EP'. Black coloured, injection moulded EPDM 'O' rings and gaskets. Shore hardness 80. Tested in-radii sizes between 1.00mm & 2.5mm. For use with water up to 85°C.
'EP7/3/7 BLK O-rings & gaskets'. Black coloured, injection moulded EPDM 'O' rings and gaskets. Shore hardness 75. The gaskets have an in-radius size of 1.0mm. The 'O' rings have an in-radius size of 1.3mm. For use with water up to 85°C.
'EP70 BLK Seals'. Black coloured, injection moulded EPDM seals. Shore hardness 70. Tested in-radius size 1.0mm. In April 2024, 'EP70 BLK 'O' rings’, black coloured, injection moulded 'O' rings were added to the approval. Shore hardness 70. Tested in-radius size of 1.3mm For use with water up to 85°C.
'HH7118F 'O' rings and gaskets'. Black coloured, compression moulded EPDM 'O' rings and gaskets. Shore hardness 70. Tested in-radius size 1.5mm. For use with water up to 85°C.
'334137 – EPDM Peroxide 70'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'PT0469'. Black coloured, injection moulded EPDM material. Shore hardness 60. Tested in-radius size 1.3mm. For use with water up to 85°C.
'EP002971PWRC'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EP7001165PWRC'. Black coloured, compression moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EPDM HT5697-4A'. Black coloured, injection moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. Between May 2024 and October 2024, the material was for use with water up to 50°C. Between November 2024 and May 2029, the material is for use with water up to 60°C.
'ML 57302'. Black coloured, compression moulded EPDM material. Shore hardness 55A. Tested in-radius size 1.0mm. For use with water up to 23°C.
‘LS40T-0301, LS50T-0301, LS60T-0301, LS70T-0301 & LS80T-0301’. Injection moulded, liquid silicone rubber sheet material, available in white, grey, black, blue, green, natural (unpigmented) & red colours. Shore hardness between 40SH-A & 80SH-A. Tested in-radius size 1.0mm. For use with water up to 85°C.
'kSil GP200, kSil GP250, kSil GP350, kSil GP400, kSil GP450 & kSil GP530'. Pale yellow/white coloured, extruded silicone rubber cellular sponge materials. Shore hardness between 37 & 70. Tested in-radii sizes between 1.53mm & 1.76mm. For use with water up to 85°C.
‘Loxeal 58-11’. Yellow coloured anaerobic adhesive paste. This product is to be applied and cured in strict accordance with the manufacturer's instructions. For use with water up to 85°C.
‘Paryls® PPSU F1550NC (natural grade – appears brown), F1550GY (grey coloured), F1550BK (black coloured) & F1550WH (white coloured)’. Injection moulded PPSU materials. For use with water up to 85°C.
'POKETONE’ range of natural (appears light brown), grey and black, injection moulded Polyketone materials. For use with water up to 85°C. 'M(a)3FG(b)A-NP0, M(a)3FG(b)A-GY(c), M(a)3FG(b)A-BK(c)'. (a) indicates the MI(g/min) or viscosity of its neat resin and is replaced with: 9 = 150~250, 3 = 40~80, 6 - 4~8 or 7 = 2~4. (b) indicates the content of glass fibre and is replaced numbers between 1 & 9 (9 indicating the maximum of 50%). NP0 indicates natural material, GY indicates grey material & BK indicates black material. (c) can indicate a random product number of each grade OR the ratio of carbon black and is replaced with numbers between 0 & 9.
Range of screw down stop valves with plastic bodies incorporating EPDM ‘O’-rings and seal. For use with PE-X pipe (manufactured to BS7291-3), BPB pipe (manufactured to BS7291-2) and copper pipe (manufactured to EN1057). Maximum working pressure and operating temperatures: 12.5 bar @ 20°C & 6.0 bar @ 65°C.
Bidet seat assembly which discharges via a sensor actuated solenoid valve and utilises a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). The inlet incorporates a strainer and flow regulator. Maximum working pressure 10.0 bar. Cold water supply only.
'122102001 Valve Body'. Black coloured, injection moulded PVC-U valve body. For use with water up to 23°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (stainless steel or brass bodies – various finishes). Flow is controlled via solenoid valve (housed in a control box) actuated via an infra-red sensor, the inlets to the control box incorporate stainless steel strainers. The spout outlets incorporates plastic aerators. The products incorporate a stainless steel PEX lined flexible hose assembly, connecting the tap to the solenoid valve. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted single hole, single outlet, fixed, electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled via an infra-red activated solenoid valve and model AF 1602 incorporates a plastic aerator in the spout outlet. Maximum working pressure 8.0 Bar Maximum operating temperature 45.0°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (brass bodies - various finishes). Flow is controlled via a solenoid valve activated via an infra-red sensor. The temperature is controlled manually with a single lever operating member. The spout outlet incorporates a plastic aerator. The inlets incorporate single check valve cartridges, however, the complete product has not been fully tested to demonstrate that it provides backflow protection. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
WC flushing cistern incorporating a side entry BS 1212-4 (2016) compact type float operated inlet valve providing a Type AG air gap with a dual flush valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of floor mounted, single-hole, single outlet (fixed), combination tap assemblies (chromium plated brass bodies), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to shower outlet. The spout outlet incorporates a plastic aerator. The product is supplied with a shower hose and handset. Maximum working pressure 5 bar. Maximum operating temperature 85°C
Range of single hole, single outlet (fixed) over the rim (swivel nozzle) bidet combination tap assemblies (brass body - various finishes, see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic flow straightener and the products are supplied with a lever type pop-up waste. Maximum working pressure: 10 Bar. Maximum operating temperature: 60°C.
Ceramic cartridge headwork with a plastic body incorporating EPDM ‘O’ rings and a stainless teel strainer. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of quarter turn ceramic disc headworks with brass bodies, intended for insertion into specifically dimensioned tap assemblies. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies, various finishes - see model) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet is a pull-out spray type which incorporates a nylon braided flexible hose incorporating a dual layer inner hose consisting of PEX inner layer and HDPE outer layer, and a manually operated button to divert between a plastic aerator and the spray function. The spray handset incorporates an approved check valve cartridge with an integral plastic flow regulator, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. Some products are supplied with a lever type or click-type pop up waste. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Single hole, single outlet (with additional outlets for filtered cold water), fixed, combination tap assembly (various plated brass), incorporating a ceramic cartridge headwork and single lever operating member. The tap body incorporates an additional push type headwork that controls the flow to a second outlet. Both outlets incorporate plastic aerators. The product is supplied with a filter assembly supplied via a brass connecting tee. Models incorporate approved single check valve cartridges; however, the complete assembly has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of single-hole, single outlet, fixed, combination tap assemblies (brass bodies – various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. The products are supplied with click-type pop up wastes. Maximum operating pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assembly (brass bodies – various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The product is supplied with a lever operated pop up waste. Maximum working pressure 5 bar. Maximum operating temperature 70 °C
Range of pillar taps, (chrome plated, brass bodies), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate plastic flow straighteners. The products are supplied with metal back nuts. Maximum operating pressure 6 bar. Maximum operating temperature 85°C
Range of single hole, single outlet, fixed combination tap assembly, (chrome plated brass bodies) incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate aerators and plastic flow straighteners. The products are supplied with a click type pop-up waste. Maximum working pressure 16 bar. Maximum operating temperature 60°C
Range of single-hole, single outlet (swivel) combination tap assemblies, (brass bodies – various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate plastic aerators. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of two-hole, single outlet, fixed combination tap assemblies, (brass bodies – various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members and a manual diverter to shower outlet. The spout outlet incorporates plastic flow straighteners. The products are supplied with a shower hose, handset and metal back nuts. Maximum working pressure 10 bar. Maximum operating temperature 60°C
Single hole, single outlet (swivel) combination tap assemblies (chromium plated brass body), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporate a plastic flow straightener or plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65˚C.
Range of single hole, single outlet, (swivel) combination tap assembly (chrome plated brass bodies) incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assemblies (chromium plated brass body), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporate a plastic flow straightener or plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65˚C.
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a dome type operating member to control the temperature. The spout outlet incorporates a plastic aerator and a detent headwork that controls the flow.. The inlets incorporate approved check valve cartridges however the complete product has not been fully tested to demonstrate It provides backflow protection. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of two hole, single outlet (fixed) combination tap assemblies (chromium plated brass or gold finish) incorporating non-rising spindle headwork with dome type or cross top operating members. The spout outlets incorporate a plastic flow straightener. The products are supplied with plastic back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headwork and a single lever operating member. The spout outlet incorporates a plastic aerator. Product is to be installed with 13 622 180 rough inset. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted, two hole, single outlet (fixed) combination tap assembly with (brass body - various finishes), incorporating a half-turn ceramic disc headwork with a dome type operating member, controlling and diverting the flow to a shower outlet. Temperature is controlled independently via a thermostatic cartridge with a dome type operating member incorporating a manual override button. The spout outlet incorporates a plastic aerator. The inlets incorporate stainless steel strainers and approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar
Non-metallic materials and components comply with BS6920 at 60°C
Page 97 of 209
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
