Range of spherical valves, with DZR brass bodies and brass ball (15mm size) or stainless steel ball (all other sizes). The products can be supplied with various operating members (see model). Jointing is achieved via a crimping tool, the 15-28mm sizes use a ‘M’ profile and the 35-54mm sizes use a ‘V’ profile. The press-fit connection is to be used with copper pipe (manufactured to EN 1057), stainless steel pipes (manufactured to EN10312) or carbon steel pipe (manufactured to EN10305-3). Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of square operated spherical valves with brass bodies, incorporating PTFE seats and a brass ball with a red coating. Maximum working pressure 40.0 Bar Maximum operating temperature 95.0°C
Range of spherical valves, with DZR brass bodies and brass ball (15mm size) or stainless steel ball (all other sizes). The products can be supplied with various operating members (see model). Jointing is achieved via a crimping tool, the 15-28mm sizes use a ‘M’ profile and the 35-54mm sizes use a ‘V’ profile. The press-fit connection is to be used with copper pipe (manufactured to EN 1057), stainless steel pipes (manufactured to EN10312) or carbon steel pipe (manufactured to EN10305-3). Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of in-line full bore spherical valves with nickel plated brass bodies, chrome plated brass ball and either lever or ‘T’ handles (see model). The products are for use with copper pipe (manufactured to BS EN 1057). Maximum working pressures: 30.0 bar (15mm-28mm) or 25.0 bar (35mm-54mm). Maximum operating temperature 99°C.
Range of angled and straight ball valves with plastic valve bodies, PTFE seats and EPDM O-rings. Maximum working pressure 16 bar. Maximum operating temperature 40°C
Gate valves with a blue epoxy coated ductile iron body, ductile iron wedge encapsulated in EPDM and EPDM ‘O’-rings. The valves operate via a non-rising spindle headwork with a hand wheel operating member. Maximum working pressures: DN50 - DN300: 25.0 bar. DN350 - 600: 16.0 bar. Maximum operating temperature 85°C.
Water chiller and heater units for under counter installation incorporating an approved double check valve at the inlet, to be used in conjunction with an outlet tap arrangement or flow control device, with a range of taps that are supplied with the chillers. Maximum working pressure 10.0 Bar Maximum operating temperature 98.0°C
'Sigrafine® EK2239, EK2200, EK2230 & EK2240'. Grey coloured, compression moulded, phenolic resin impregnated carbon rings. For use with water up to 85°C.
'Dicoat 60 EX Blue'. Factory applied, blue coloured, two-component epoxy coating. Mix in a 3:1 volume ratio and apply as per manufacturer's user instructions 'SPL/R&D/TTD/UI/007', version '01', dated '03.11.2022'. Cure for 7 days@30°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPONICS WP-NS (No. 20170209)'. Factory applied, dark grey coloured, two-component, solvent free epoxy resin coating consisting of a base and hardener. Mix base and hardener in a weight ratio of 7:3 and apply as per Product Data Sheet ‘1838-K’ dated February 2017. Cure for 168 hours@30°C, then 168 hours@60°C and 'rest' for 168 hours before use. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CP231200'. Factory applied, two-part water-based epoxy coating. Mix Parts A & B in a 5:1 weight ratio and apply as per manufacturer's instructions 'File No. HBB-01', 'Version: A', dated '2024.6.30'. Cure for 24 hours@26°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotaguard VA 5001'. Factory applied, blue coloured epoxy coating. Apply as per manufacturers technical data sheet dated 9th November 2015. Cure for 2 minutes, 30 seconds@232°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TOHPEPOWDER#6150 SHK GRAY QD'. Factory applied, grey coloured epoxy coating. Apply as per Tohpe Corporation instructions no '4230904550B'. dated 'Jan 28, 2025'. Cure for 5 minutes@200°C. For use with water up to 65°C.
'JERLAC Two Pack Epoxy Beige-740'. Factory applied, two-part, beige coloured epoxy coating. Mix in a 3:1 volume ratio and apply as per manufacturer's data sheet issue number '01', dated '10.01.2024'. Cure for 7 days@30°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Hempadur 35530 System’. Grey coloured, factory applied, two-component epoxy coating comprising of ‘Hempadur 35530 red (51320) and Hempadur 35530 grey (10500)’. ‘Hempadur 35530 red (51320)’ comprises of a base and curing agent which are mixed in a 3:1 volume ratio. ‘Hempadur 35530 grey (10500)’ comprises of a base and curing agent which are mixed in a 3:1 volume ratio. Apply as per manufacturer's Product Data Sheet dated October 2024. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Nylon 11'. Factory applied nylon coatings available in white or grey colours. The substrate the coating is to be applied to is heated to 310°C for 30 minutes and the coating applied as per manufacturer's work instructions 'WI-09-19 Rev. 6' dated April 22, 2020. Cure for 10 minutes@270°C. The white coating is for use with water up to 23°C. The grey coating is for use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jindal Saw Limited Ordinary Portland Cement - 53 Grade'. Factory applied, grey coloured Ordinary Portland Cement. Mix cement, sand & water in a xx ratio of 1:1.5:0.5 and apply as per manufacturer's Work Instructions 'JSAW/AP01/DISP/PRO/WI-09', version '2.0', effective date '01.05.2023'. Cure for 2.5 hours@48°C and then 3 days@30°C. For use with water up to 60°C.
'SikaTop®-107 Seal AE'. Site applied, grey coloured, two-part coating. Mix parts A and B in a 1.4 weight ratio and apply as per manufacturer's Method Statement 'V1', dated 'Feb 2025'. Cure Coat 1 for 3 hours at 30°C. Cure Coat 2 for 21 days at 30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'KLINGERSIL® C-4430'. NBR/fibre gasket material, which is green coloured one side and white coloured the other, manufactured by calandering. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'MS Schramberg Sintered Strontium Ferrite (10-1173001)'. Grey coloured Sintered Strontium Ferrite ring component. For use with water up to 85°C.
Page 91 of 108
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
