Range of wall mounted bar type thermostatic shower vavles, (brass bodies – various finishes) incorporating a ceramic disc diverter cartridge controlling the flow, with a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member that incorporates a manual override button. The inlets incorporate a single check valve cartridge (however, the complete product has not been fully tested to demonstrate it provides backflow protection) and stainless-steel strainers. This product is supplied with a hose, handset and overhead shower. Maximum working pressure 5 bar. Maximum operating temperature 65°C
Range of wall mounted thermostatic, bar type shower valves. Models (801509 & 801510) incorporate quarter turn ceramic disc headworks and model (801508) incorporates a non-rising spindle headwork controlling the flow. The temperature is controlled independently via a thermostatic cartridge that incorporates a manual override button. Both using either dome, cubed or single lever type operating members. The inlets incorporate stainless steel strainer washers and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10 bar. Maximum operating temperature 65°C
Range of wall mounted, thermostatic mixer valve with brass bodies, diverter headwork that controls flow between two or three outlets (see model) with various type of operating member. The temperature is controlled independently via a thermostatic cartridge operating member with a manual override button. Inlets incorporate a stainless-steel strainer and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 55°C
Wall mounted, shower control valve, (brass body – various finishes), incorporating a half turn ceramic disc headwork using a dome type operating member. The shower outlet connection incorporates an approved check valve cartridge (however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection). Maximum working pressure 10 bar. Maximum operating temperature 70°C
Range of in-line, adjustable pressure reducing valves, with a DZR brass body. The product incorporates two approved check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 3) and a shut off valve. Maximum working pressure 16 Bar Maximum outlet pressure between 1.5 bar and 6.0 bar.
Non-metallic materials and components comply with BS6920 at 40°C
Inlet control group consisting of an in-line pressure reducing valve (adjustable pressure - see model) and a pre-set expansion relief valve (pre-set pressure - see model) housed in a DZR brass body with an EPDM rubber diaphragm. The product incorporates a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Compression connection to be used with copper pipe EN1057 only. Maximum supply pressure 10.0 bar. Maximum operating temperature 40°C.
In-line spherical valve with a chrom eplasted DZR brass body, brass ball and EPDM ‘O’-rings, incorporating a single check valve cartridge (verified by test, suitable for fluid catergory 2) with a lever operating member. To be used with copper pipe manufactured to EN1057. verified Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of brass or DZR brass spherical valves incorporating single lever operating members and a chrome plated brass ball. Model 0312A030307DC is an angled 90-degree valve which incorporates single check valve cartridges verified by test (suitable for backflow protection against Fluid Category 2 or 3). For use with EN1057 copper pipe. Maximum working pressure 10 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of unvented monobloc groups consisting of an in-line pressure reducing valve (PRV) (adjustable between 2.7 and 3.3 bar or 3.2 and 3.8 bar - see model) and a pre-set expansion relief valve (SRV) (pre-set at either 4.5, 4.75, 5.0, 6.0 or 8.0 bar - see model) housed in a DZR brass body with an EPDM rubber diaphragm. The product incorporates a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). The expansion relief valve is fitted with a rotary type easing gear and the products are for use with copper pipe (manufactured to EN1057). Maximum inlet supply pressure 10.0 bar. Maximum operating temperature 85°C.
Range of scale inhibitor units with plastic body which uses sodium calcium polyphosphate. The assemblies incorporate a single check valve cartridge (suitable for backflow protection against fluid category 2). Maximum working pressure 6.5 bar. Cold water use only.
Non-metallic materials and components comply with BS6920 at Cold water use only°C
'Buffalo PUR500'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated '14/08/2018'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Mungo Injection System MIT800RE'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated 'Jun-23'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Single hole, triple outlet (swivel) combination tap assembly (brass bodies, various finishes - see model), incorporating a ceramic cartridge headwork with single lever operating member. Electronic controls allow the tap to dispense boiling, chilled or sparkling water. The vented models are supplied with a brass adaptor containing a plastic flow regulator and a combined EPDM washer and stainless-steel strainer, for installation on the mains cold water into the ceramic cartridge. They are also supplied with a stainless steel braided PEX lined flexible hose assembly and a stainless steel braided TPSiV lined flexible hose assembly both with ½” captive nut end connections for installation between the tap and a command centre, (which is not included as part of this approval). Maximum working pressure 5.0 bar. Maximum operating temperatures: Near boiling water circuit: 100°C. Ambient hot and cold (mixed) circuit: 65°C. Chilled/Chilled and sparkling circuit: Cold water use only.
Floor mounted single hole, single outlet (fixed), combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to shower outlet. The spout outlet incorporates a plastic aerator or flow straightener. The product is supplied with a shower hose and handset. Maximum working pressure - 10 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Spring loaded resilient trim check valve cartridge with stainless steel spring and EPDM `O`-ring. For insertion into specifically dimensioned bores. Maximum working pressure 16 Bar. BS6920 at 85°C
Range of Type TK spring loaded, resilient trim, in-line check valve cartridges. For insertion into specifically dimensioned bores. Maximum working pressure 10.0bar. Maximum operating temperature 65ºC.
Spring-loaded resilient trim in-line check valve cartridge with a plastic body, incorporating a stainless-steel spring and EPDM ‘O’-rings . For insertion into specifically dimensioned bores. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spring-loaded resilient trim in-line check valve cartridges with plastic bodies, incorporating a stainless-steel spring and EPDM ‘O’-rings. For insertion into specifically dimensioned bores. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of non-verifiable double check valve assemblies consisting of two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies. Maximum working pressure 16.0 bar Maximum operating temperature 85°C
Double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges within a DZR brass body. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Page 82 of 139
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
