Electrolytic scale inhibitors incorporating copper or nickel coated copper bodies. Compression models are to be used with copper pipe manufactured to BS EN1057. Maximum working pressure 10.0 bar. Cold water use only.
Range of UV disinfection units. Maximum working pressure 6.9 bar. Cold water use only.
Range of electronically controlled ion exchange water softeners (salt regenerated) for commercial and domestic use. Maximum working pressure 5.0 bar. Cold water use
Electronically controlled, commercial ion exchange water softeners. Maximum working pressure 7.0 bar. Cold water use only
'Epoxy PB Pipe Green (W) & Epoxy FB Pipe Green (HW)'. Factory applied, green coloured epoxy powder coatings. The substrate to which the coating is to be applied is pre-heated to 220˚C for 15 minutes before applying the coating as per product data sheet dated '27th June 2023'. Post-cure for 15 minutes@215°C. For use with water up to 85°C. This material is only approved for the pre-heat and post-cure conditions that appear on the approval. If the pre-heat and/or post-cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Versapox PW'. Factory applied, grey coloured, two component solvent free epoxy coating. Mix base and curing agent in a 3:1 volume ratio and apply as per manufacturer's product data sheet 'issue No. 01', dated 'Jan 2022'. Cure for 10 days@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘PULRON 101 AQUA’. Factory applied, green coloured polyethylene coating. Apply a single coat (200μm thickness) as per manufacturer's instructions 'ELS.TT.C01.40', 'Rev00', dated '13.06.2023', Cure for 10 minutes at 200°C. Between June 2023 and December 2024, the material was for use with water up to 23°C. Between January 2025 and June 2028, the material is for use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Non-metallic materials and components comply with BS6920 at 65°C°C
'RF (Riyadh Foundry)'. Factory applied, grey coloured cement. Mix cement, sand and water in a 1:1.5:0.6 weight ratio and apply as per manufacturer's work instruction 'WI.PR.07', revision '01/01/', dated '16.02.2022'.. Cure for 3 hours@25°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'HKUST002'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's instructions 'HKUST002101001', '01', dated '03/11/2020'. Cure for 168 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Electrocoat EP812 Blue'. Factory applied, blue coloured, two-part epoxy coating consisting of a base and hardener. Mix base and hardener in a volume ratio of 3:1 and apply as per manufacturer's data sheet 'ECL / TDS / EP 812 - BLUE, RAL 5017', issue date '12-Jan-13', version '03', revision date '25-Sept-14'. Cure for 1 hour@60°C followed by 7 days@28°C. For use with water up to 23°C. From March 2024 the material is for use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPW-6575S8T-20 Epoxy RAL 5005'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's TDS 'Rev:00/December 2022'. Cure for 10 minutes at 200°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Promag’. Factory applied, black coloured PUR coating system comprising of a primer and topcoat. ‘Promag Primer’ is a two-part primer to be mixed in a 1:2 mass ratio before applying as per manufacturer’s core instructions ‘TLB: 10000043811’, ‘Version: M’. Cure/dry for 2 hours@23°C. ‘Promag Topcoat’ is a three-part topcoat to be mixed in a 92.59:5.19:2.22 mass ratio before applying as per manufacturer’s core instructions ‘TLB: 10000043811’, ‘Version: M’. Cure/dry for 20 seconds@20-26°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Purtop 1000 N'. Factory applied, two component, grey coloured polyurea coating. Mix components A & B in a weight ratio of 1:1 and apply as per manufacturer's TDS '7506-2-2023'. Cure for 48 hours@23°C. For use with water up to 23°C. This material is only approved for the mixing, curing & soaking conditions that appear on the approval. If the mix/cure/soak conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hyperlast™ 500WP Polyol and Hyperlast™ 500WP prepolymer'. Site applied, grey coloured (once mixed), two-component polyol and prepolymer based coating. Mix Part A (grey liquid) with Part B (amber liquid) in a volume ratio of 1:1 and apply as per manufacturer's 'General Method Statement, DOW WATERPOTABLE 500, Edition 1 07/23'. Cure for 24 hours@7°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Vorastar™ 5342WP Polyol and 'Vorastar™ 5342WP prepolymer'. Site applied, cream coloured (once mixed), two-component urethane based coating. Mix Part A (amber liquid) with Part B (amber liquid) in a volume ratio of 1:1 and apply as per manufacturer's 'General Method Statement, DOW WATERPOTABLE, Edition 1 07/23'. Cure for 24 hours@7°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Teadit NA 1002'. Green coloured fibre/NBR gasket material manufactured by calendaring. For use with water up to 65°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'A001 (natural) & A002 (black)'. Extruded, natural (colourless) or black coloured PVC hoses. For use with water up to 65°C.
'ForTii® WX11-FC NA99001 (Natural)'. Natural (appears cream coloured), injection moulded polyamide material. For use with water up to 85°C.
'PLUSTEK PB306G6BL151'. Blue coloured, injection moulded, polyamide material (30% glass fibre reinforced). For use with water up to 85°C.
'VYDYNE AG7K-BK1066'. Black coloured, (35% glass Fibre reinforced) polyamide 66 material. From 1st April 2023 until 29th May 2024, the material was for use with water up to 23°C. From 30th May 2024 until 30th April 2028, the material is for use with water up to 70°C.
'VYDYNE AG10K-BK1066'. Black coloured, (50% glass Fibre reinforced) polyamide 66 material. For use with water up to 23°C. From January 2024, the material is for use with water up to 60°C.
'ELCRIN WF006LiQ-1001'. Grey coloured, injection moulded, glass fibre reinforced PBT material. For use with water up to 85°C.
'AQUA Cable®'. Extruded, blue coloured cable with polyethylene sheath (water contact layer), available with between 1 and 5 metallic cores and a wall thickness of between 1.2mm & 5.9mm. For use with water up to 23°C.
'Hepworth HDPE PE 100 Pipe (black) & HDPE PE 100 Pipe (black with blue stripes)'. Extruded polyethylene pipes. For use with water up to 60°C.
‘Sikaplan® WT 4220-15 C & Sikaplan® WT 4220-18 H’. ‘Sikaplan® WT 4220-15’ is a light blue coloured, extruded multi-layer polyethylene sheet material comprising of glass fibre inlay between two polyethylene sheet layers. ‘Sikaplan® WT 4220-18 H’ is a light blue coloured, extruded polyethylene sheet material. For use with water up to 60°C.
'NEPROPLAST Multi-layered and Single layered pipes'. The single layered pipe is green coloured, extruded PP-R. The multi-layered pipes are extruded and have a green coloured PP-R inner layer and black coloured PE100 outer layer (with or without a red stripe). For use with water up to 70°C.
'ACOFLON 100 – INO220FF Washer'. White coloured, pressure moulded and then machined PTFE washer. For use with water up to 80°C.
'ESTANE® 58197 Nat 022'. In August 2023 'ESTANE® 58197 NAT 01' was added to the approval. Natural (transparent, colourless), injection moulded thermoplastic polyurethane materials. For use with water up to 85°C.
‘Estane® Grades 58887 Nat 036, 58315 Nat 033, 58300 Nat 036, 58887 Nat 029, 58315 Nat 055, 58887 Nat 038 & 58887 Nat 055’. Natural (transparent, colourless), injection moulded TPU materials. For use with water up to 23°C.
‘PVDF Solef 1008/0001’. White coloured, injection moulded PVDF material. For use with water up to 85°C.
‘Sikadur 31 DW Rapid for use with Combiflex TF Tape’. Site applied, grey coloured two-component epoxy resin for use with grey coloured TPE Tape. Mix parts A & B of ‘Sikadur 31 DW Rapid’ in a 3:1 weight ratio and apply as per product data sheet ‘March 2021, Version 01.03’. Immediately apply ‘Combiflex TF Tape’ as per product data sheet ‘May 2021, Version 01.01’ and cure for 7 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Sikadur 31 DW for use with Combiflex TF Tape’. Site applied, grey coloured two-component epoxy resin for use with grey coloured TPE Tape. Mix parts A & B of ‘Sikadur 31 DW’ in a 3:1 weight ratio and apply as per product data sheet ‘February 2022, Version 03.03’. Immediately apply ‘Combiflex TF Tape’ as per product data sheet ‘May 2021, Version 01.01’ and cure for 7 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'5613 Gaskets'. Black coloured, compression moulded EPDM gaskets. Shore hardness 60. Tested in-radius size 3.0mm. For use with water up to 23°C.
'TIMO 4-80 ‘O’ rings and washers'. Black coloured, injection moulded EPDM ‘O’ rings and washers. Shore hardness 80. The ‘O’ rings have an in-radius size of between 0.52mm & 2.67mm. The washers have an in-radius size of between 0.52mm & 2.71mm. For use with water up to 85°C.
'SE-618PF'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
Initial approval was for ‘REK-8000-Premium’ (shore hardness 80) only. In April 2024 ‘REK-5000-Premium’ (shore hardness 50) & ‘REK-7000-Premium’ (shore hardness 70) were added to the approval. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 80. Tested in-radius size 1.0mm. For use with water up to 23°C.
'EPDM H 85'. Black coloured, compression moulded EPDM rubber material. Shore hardness 85. Tested in-radius size 1.10mm. For use with water up to 70°C.
'Mescola EPDM-PX 659/70.nr'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'SN-738PF'. Black coloured, compression moulded NBR rubber. Shore hardness 71. Tested in-radius size 1.0mm. For use with water up to 23°C. From December 2023, the material is suitable for use with water up to 85°C.
‘N70 60 003 197’. Black coloured, injection moulded NBR material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'Akfix PS253 Pipe Sealant Medium Strength'. Blue coloured pipe sealant. Apply as per manufacturer's TDS 'Rev.01', issue date '23/10/2019'. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hinton Solvent Cement HSC125 & HSC250'. Clear, transparent (un-pigmented) solvent cement, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions 'Rev00 02062023'. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'IRWR55'. Black coloured, compression moulded IIR rubber membrane/diaphragm. Shore hardness 51. Tested in-radius size 1.01mm. For use with water up to 23°C.
Side entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by an electronically controlled flush valve. Maximum working pressure 10.0 bar. Cold water use only
WC flushing cistern incorporating a side entry BS 1212-4 compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by electronic or manual actuation. Maximum working pressure 10.0 bar. Cold water use only
Range of Concealed WC dual flushing cistern with a vertical BS 1212-4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly. Maximum working pressure -10 Bar Maximum operating temperature - cold water use only Models T1910 & T1911 can now incorporate a T8702 flush valve. Maximum working pressure 10 Bar, cold water use only.
Three-hole, single outlet (fixed), combination tap assembly (brass body – various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to the shower outlet. The product is supplied with a stainless-steel braided EPDM lined flexible connection hose to connect the head work to the spout outlet. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Wall mounted, three-hole, single outlet, fixed combination tap assembly (chrome plated brass body), incorporating a ceramic cartridge headwork with a single lever operating member. The product is supplied with a shower handset holder that incorporates a manual diverter and a cascade type spout outlet. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted, three-hole, single outlet, fixed combination tap assemblies (brass bodies – various finishes). Incorporating ceramic cartridge headworks with single lever operating members. The product incorporate shower handset holders that incorporate manual diverters. The spouts incorporate plastic aerators. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Page 77 of 209
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
