'WB-108'. Factory applied, two-component, grey coloured epoxy coating. Mix, apply and full cure (7 days@20°C) as per manufacturer's technical data sheet 'file no. TWJ-WB-108', 'edition: A1' dated 01/12/2020. For use with water up to 65°C.
'Epoxy phenolic FBE-4 RAL 5010'. Factory applied, blue coloured epoxy phenolic coating. Apply as per manufacturer's instructions dated '11/20'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPOXY TB BT Grey RAL 7016'. Factory applied, grey coloured, fusion bonded epoxy coating. Apply as per Technical Data Sheet 'document version:1' dated 'June 22, 2021'. Cure for 10 minutes@160°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`3011 high chlorinated polyethylene anticorrosive coating`. Factory applied, burgundy coloured polyethylene coating. Apply and cure as per manufacturers `IFU Version no. 03' dated June 18 2020. For use with water up to 23°C.
'DELTAPrime 2K SF Primer and DELTAShield HP 500 PW Coating'. Factory applied, grey coloured (once mixed), two-component primer (non-water contact primer) and two-component coating (water contact coating). Mix and apply DELTAPrime 2K SF Primer as per Product Data Sheet ‘October 2019-001’. Cure for 2 hours@25°C. Then mix and apply DELTAShield HP 500 PW Coating as per Product Data Sheet ‘190625’. Cure for 1 minute@25°C. For use with water up to 85°C.
'H-453'. Factory applied, grey coloured ceramic epoxy coating. Apply as per Technical Data Sheet file no. 'TWJ-H-453', edition 'A2', dated '01/03/2020'. Cure for 5 days@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`9011 Epoxy anticorrosive coating`. Factory applied, black coloured epoxy coating. Apply and cure as per manufacturers `IFU Version no. 03' dated June 18, 2020. For use with water up to 23°C.
'KINTE Epoxy Resin Coating (ES-BL10724-S9)'. Factory applied, blue coloured coating. Apply and cure as per manufacturer's instructions issued 'March 2018 V5.2'. For use with water up to 85°C.
'FY-6 (white coloured) & FY-5 (blue coloured)'. Factory applied epoxy powder coatings. Apply and cure as per manufacturer's instructions ‘fyzj2020925 version 1' dated '2020-9-20'. For use with water up to 85°C.
`Jotaguard VA 5001`. Factory applied, dark blue coloured fusion bonded epoxy coating. Apply and cure as per manufacturers test method document no. '39.40.014', issue date '02.01.2018', revision no. '02'. For use with water up to 85°C.
'Jazeera Proofex (formerly known as Jazeera Proof DW)'. Site applied, two-component, grey coloured cementitious coating. Mix Part A (grey coloured powder) with Part B (white, opaque liquid) in a 2:1 mass ratio. Cure for 28 days@25°C. For use with water up to 40°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Brushbond FLXIII'. Site applied, grey coloured, two-part elastomeric/cementitious coating. Mix and apply in accordance with manufacturer's instructions 'v10' dated October 2020. Cure coat 1 for 18 hours@7°C. Cure coat 2 for 21 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Acrylatik'. Site applied, Acrylate primers available in white, red, blue and black colours. Apply as per manufacturer's instructions 'Appendix No. 1, TU 2316-002-92 872914-2016' dated '11.02.2016'. Cure for 20 minutes@20°C and then 20 minutes@90°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EZY-PAK™ #100 Packing Compound'. White coloured, PTFE packing compound. Apply as per 'Jet-Lube' TDS for 'EZY-PAK™ #100'. For use with water up to 23°C.
'Extralite Pipe'. Light green/brown coloured GRP pipe manufactured by filament winding. For use with water up to 60°C.
'Extralite Fitting'. Brown coloured GRP fitting manufactured by hand lay-up. For use with water up to 60°C.
'ajpipe GRP Pipe'. Beige coloured GRP pipe manufactured by continuous filament winding. For use with water up to 23°C. From February 2024, the pipe is for use with water up to 60°C.
'Saphir DIMATIT Pipe'. Pale green coloured GRP pipe manufactured by continuous filament winding and manual lamination. For use with water up to 23°C.
'SNB GRP Panel'. Beige coloured, hot press moulded GRP panel. For use with water up to 50°C.
'S-006TG'. Cream coloured, compression moulded GRP panel. For use with water up to 23°C.
'IPF-GRP-H2O'. Off-white/beige coloured GRP/GRV pipe manufactured by filament winding. For use with water up to 60°C.
'IPF-GRP-H2O'. Off-white/beige coloured GRP/GRV pipe manufactured by filament winding. For use with water up to 60°C.
'DAEWOO GRP Panel'. Beige coloured, hot press moulded GRP panel. For use with water up to 50°C.
`SIGRAFLEX® APX`. Grey coloured, expansion/compression moulded graphite material. For use with water up to 85°C.
'CRG S'. Transparent, single layer, extruded polyethylene hose. For use with water up to 85°C.
'XIN-6709-01 hose' manufactured from 'GR-PVC 001N' raw material. Single layered, extruded, black coloured PVC hose. For use with water up to 85°C.
'Purolite® FerrIX™ A33E'. Brown coloured ion exchange resin. For use with water up to 23°C.
'Purolite® A600E/9149'. Yellow coloured ion exchange resin. For use with water up to 23°C.
'Purolite® A502PS'. Cream coloured ion exchange resin. For use with water up to 23°C.
'Purolite® A860S'. White coloured ion exchange resin. For use with water up to 23°C.
'C107DQ (Na), C108DQ (Na) & C110DQ (Na)'. Light yellow coloured ion exchange resins. For use with water up to 23°C.
'SAGITTA VP 763 Silicone Grease'. White coloured, opaque silicone grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
`Griffon P-20` Lubricant. White coloured lubricant in the form of a paste. Apply as per manufacturer's instructions. No cure required. For use with water up to 23°C.
'IKV Tribostar STF 2501 & Addisil WTG 1'. Translucent, white coloured silicone greases. Apply as per manufacturer's instructions. For use with water up to 85°C.
AKROMID® A3 GF 25 8 HU natural (8120) AKROMID® A3 GF 30 8 HU natural (8102) AKROMID® A3 GF 33 8 HU natural (8128) AKROMID® A3 GF 35 8 HU natural (8121) AKROMID® A3 GF 40 8 HU natural (8122) AKROMID® A3 GF 43 8 HU natural (8130) AKROMID® A3 GF 45 8 HU natural (8123) AKROMID® A3 GF 50 8 HU natural (8124) AKROMID® A3 GF 55 8 HU natural (8125) AKROMID® A3 GF 60 8 HU natural (8126) AKROMID® A3 GF 25 8 HU black (8118) AKROMID® A3 GF 30 8 HU black (8112) AKROMID® A3 GF 33 8 HU black (8129) AKROMID® A3 GF 35 8 HU black (8113) AKROMID® A3 GF 40 8 HU black (8114) AKROMID® A3 GF 43 8 HU black (8131) AKROMID® A3 GF 45 8 HU black (8115) AKROMID® A3 GF 50 8 HU black (8116) AKROMID® A3 GF 55 8 HU black (8119) AKROMID® A3 GF 60 8 HU black (8117) Natural (appears white) and black coloured, injection moulded, glass fibre reinforced PA66 materials. For use with water up to 85°C.
'Ultradur® B4300 G6 HR FC Aqua grey 35413 '. Grey coloured, injection moulded PBT material. For use with water up to 65°C.
'Sirester EC 0994/AT/V/15'. Pale green coloured orthothalic resin manufactured by hand lay-up. For use with water up to 23°C.
'Sirester IS 4245/C'. Pale yellow coloured isothalic resin manufactured by hand lay-up. For use with water up to 23°C.
`Polygel-2132`. Yellow coloured, contact moulded Gelcoat. For use with water up to 50°C.
'100 US Gallon Dubai Polytank Panel'. Triple layered, rotationally moulded LLDPE tank panel comprising of a white coloured inner layer, black coloured middle layer and white coloured outer layer. For use with water up to 65°C.
'Radius Systems Socket Fittings and Saddle Fittings'. Black coloured, injection moulded PE fittings. For use with water up to 60°C.
'Revolve 6402U'. White coloured (translucent), polyethylene material manufactured by rotational moulding. For use with water up to 85°C.
'PE-BWG'. Transparent, extruded, single layer, polyethylene hose. In July 2023, 'PE-BWG Black', a black coloured (opaque), extruded, single layer, polyethylene hose was added to the approval. For use with water up to 85°C.
'Al Bassam High Density Polyethylene Underground Water Tank Panel'. Black coloured, blow moulded HDPE tank panel which is available with three or four layers (of the same material). For use with water up to 65°C.
'Al Bassam High Density Polyethylene Aboveground Water Tank Panel'. Blow moulded HDPE tank panel which comprises of four layers and has a black coloured water contact layer, red and black coloured inner layers and white coloured outer (non-water contact) layer. For use with water up to 65°C.
'Heliklima PE-RT/AL/PE-RT pipes'. Triple layered, extruded pipe comprising of a white coloured (translucent) inner layer, aluminium middle layer and white coloured (opaque) outer layer. For use with water up to 85°C.
'BKBB-660'. Black coloured LLDPE 'buoyant body' manufactured by rotational moulding. For use with water up to 23°C.
'XSPE-GPE01'. Black coloured (with blue stripes), extruded polyethylene pipe. For use with water up to 23°C.
'Hostalen GM 5010 T3 Black'. Black coloured, extruded HDPE material. For use with water up to 23°C.
'HD 8570.29'. Natural (appears white with black specks), high density polyethylene resin material manufactured by rotational moulding. For use with water up to 85°C.
Page 8 of 64
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
