'Parixit HDPE Pipe'. Blue coloured, extruded HDPE pipe. For use with water up to 60°C.
'Parixit HDPE Fitting'. Blue coloured, injection moulded HDPE fitting. For use with water up to 60°C.
'Kuzeyboru HDPE 100 Pipe'. Black coloured, extruded HDPE pipe. For use with water up to 23°C.
'Revolve 4068/N-250 (white coloured), M-586 (black coloured), M-638 (black coloured), M-694 (black coloured) & M-695 (black coloured)'. Polyethylene materials manufactured using rotational moulding. For use with water up to 85°C.
'SAB A16 Compression Fittings'. Black coloured, compression fitting bodies, injection moulded from polypropylene (PP-B). For use with water up to 60°C.
`Maxxam PP Flow Meter Insert`. Off-white coloured, injection moulded polypropylene flow meter insert. For use with water up to 23°C. From September 2023, the component is for use with water up to 85°C.
'Supreme S16 Compression Fittings'. Black coloured, compression fitting bodies, injection moulded from polypropylene (PP-B). For use with water up to 60°C.
'Moplen EP 300 K PP Cover'. White coloured, translucent, injection moulded polypropylene cover. For use with water up to 85°C.
EP80/2 BLK 'O' rings & gaskets. Black coloured, injection moulded EPDM 'O' rings & gaskets. Shore hardness 80. Tested in-radius size 1.5mm. . For use with water up to 85°C.
'09-557'. Black coloured, compression moulded EPDM 'strip'. Shore hardness 80. Tested in-radius size 2.0mm. For use with water up to 85°C.
'EP5700'. Black coloured, compression moulded EPDM material. Shore hardness 57. Tested in-radius size 0.98mm. For use with water up to 23°C.
'EP70B002'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'DLYY E6202'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 23°C.
'Loxeal UVAE 83-50 HT Fluo'. Green coloured anaerobic adhesive. For use with water up to 85°C. These products are to be applied and cured in strict accordance with the manufacturer's instructions.
'Weld-On 724'. Orange coloured solvent cement. Apply as per manufacturer's product data sheet. Cure for 10 minutes@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Ixef DW/FC 1032 BK001 (black coloured) & Ixef DW/FC 1032 NT000 (natural, appears off-white coloured)'. Injection moulded PARA (polyarylamide) materials. For use with water up to 85°C.
'Hytrel® 6359FG & 4068FG'. Cream coloured, injection moulded, thermoplastic polyester elastomeric materials. For use with water up to 85°C.
`Aqua Clean Mera` range of bidets incorporating an electronically operated seat, flow is controlled by solenoid valve and discharges via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 10.0 bar. Cold water supply only.
'EcoFITTOM Fittings'. Blue coloured PVC fittings which are manufactured by extrusion and molecular orientation. For use with water up to 60°C.
'TOM PVC-O Pipe'. Blue coloured PVC pipe which is manufactured by extrusion and molecular orientation. For use with water up to 60°C.
Single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass), flow is controlled by a solenoid valve activated via an infra-red sensor. The tap connects to the solenoid valve via a copper tail with a ½” BSP (F) captive nut and a fibre washer. The product is supplied with a combined TPE washer and stainless steel strainer to be installed on the inlet to the solenoid. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass), flow is controlled by a solenoid valve activated via an infra-red sensor. The tap connects to the solenoid valve via a copper tail with a ½” BSP (F) captive nut and a fibre washer. The product is supplied with a combined TPE washer and stainless steel strainer to be installed on the inlet to the solenoid. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) electronically operated, tap assemblies (chromium plated brass). Flow is controlled via solenoid valve and actuated by a touch sensor. The spout outlets incorporate a plastic aerator, supplied with stainless steel strainers. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of side entry BS1212-4 (2016) delayed action or non-delayed action type float operated valves for WC flushing cisterns. The inlet incorporates an optional flow restrictor. Maximum working pressure 10.0 bar. Cold water use only.
BS EN 14055: 2018 concealed WC cistern incorporating a side or bottom entry compact type float operated inlet valve providing a Type AG air gap with a pneumatic or cable operated drop valve capable of full flush volumes of up to 6 litres and reduced flush of up to 4 litres. The cistern is operated by a manual push button. Maximum working pressure 10.0 bar. Cold water use only.
BS EN 14055: 2018 concealed WC cistern incorporating a side entry compact type float operated inlet valve providing a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5) with a pneumatic or cable operated drop valve capable of full flush volumes of up to 6 litres and reduced flush of up to 4 litres. The cistern is operated by manual push button. Maximum working pressure 10.0 bar. Cold water use only.
Range of deck mounted, three-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork and manually operated diverter valve, both models RAKSOR3013C and RAKPOR3013C use single lever operating members and model RAKAMA3013C has a dome type operating member. The spouts incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of three hole, single outlet (fixed) combination tap assembly (chromium plated brass). Incorporating ceramic cartridge headworks, single lever operating members & manually operated diverter to shower outlet. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Rainwater top up cistern with flow controlled by solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Product also incorporates a stop valve, a flow restrictor and a float valve on the inlet. Maximum working pressure 10.0 bar. Cold water use only.
Spring loaded, resilient trim, in-line check valve cartridge with plastic guide, stem, body and EPDM O-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Spring loaded resilient trim in-line check valve cartridge with plastic guide, stem and housing, stainless steel spring and EPDM ‘O’-rings. For insertion into specifically dimensioned bores. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘Parker 500’ assisted bathing unit. Flow is controlled via a thermostatic mixing valve, the inlet of which incorporates a stainless steel strainer and single check valve cartridge (suitable for backflow protection against Fluid Category 2) and feeds either a bath spout outlet or shower handset which incorporates a self-closing trigger. The inlet to the shower handset incorporates a plastic flow restrictor and a single check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. There is a combined spherical valve and strainer on the inlet to the bathing unit which incorporates a single check valve cartridge (suitable for backflow protection against Fluid Category 2). The ‘shepherds crook’ type shower outlet is protected via an AUK3 airgap arrangement. Maximum working pressure 6.0 bar. Maximum operating temperature 80°C
`Silverline` range of sectional hot-pressed GRP cold water storage cisterns with butyl seals and stainless-steel bolts and tie rods. Supplied with WRAS approved byelaw 30 kits Cold water use only.
ANP range of pre insulated one piece contact moulded GRP cold water storage cisterns and covers. Supplied with a wholesome water kit, consisting of a screened vent, screened warning pipe and screened overflow pipe. Cold water use only.
One-piece (white) HDPE plastic storage cistern with lid. Maximum operating temperature 60°C.
Range of hot pressed moulded GRP sectional cold water storage cisterns. Larger cisterns are fitted with PVC roof supports and are supplied with stainless steel ladders, tie rods, braces and hatches. Cold water use only.
An aerator attachment for a mixer tap with a black plastic body and NBR O-rings. The outlet incorporates a stainless-steel strainer. This product incorporates swivel joint and a mechanism that alters the flow from jet to spray. Maximum working temperature 60°C.
Ceramic cartridge headwork with plastic body and silicone seals, for insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of quarter turn and half turn ceramic disc headworks with brass bodies and silicone rubber gaskets for insertion into specifically dimensioned assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of ceramic cartridge headworks with plastic bodies and silicone ‘O’-rings and gaskets for insertion into specifically dimensioned tap assemblies. Maximum working pressure 12.0 bar. Maximum operating temperature 85°C.
Range of non-rising spindle headworks incorporating brass bodies, NBR rubber `O`-rings and silicone rubber gaskets. Model CL1/2M-360T 360° incorporates a non -rising spindle headwork, model CL1/2K-180T-10 incorporate a half turn ceramic disc headwork and other models incorporate a quarter turn ceramic disc headwork. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Manually operated 2-way diverter valve headwork, with a plastic body and silicone seals. To be inserted into specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum working temperature 85°C.
Manually operated 2-way diverter valve headwork, with a plastic body and silicone seals. To be inserted into specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum working temperature 85°C.
Range of non-rising headworks incorporating brass bodies, NBR ‘O’-rings and EPDM gaskets. The products are intended for insertion into specifically dimensioned tap assemblies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a quarter turn ceramic disc headworks and single lever operating members, with a pull out spray retained within a holster. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass). incorporating a ceramic cartridge and single lever operating member with a spring loaded, pull down trigger operated spray. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet fixed combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener and the product is supplied with a click type waste. Maximum operating pressure 5.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet of model 825JK incorporates a plastic aerator. Products are supplied with a click type waste. Maximum operating pressure 5.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes) incorporating a ceramic cartridge headwork with single lever operating members. The spout outlets incorporate a plastic aerator. Product is supplied with a pop-up waste. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (waterfall spout) combination tap assembly with brass body (various finishes), incorporating a ceramic cartridge headwork with single lever operating member. The inlets incorporate a stainless-steel strainer and the product is supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60ºC.
Page 8 of 231
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
