Kuterlite K900 Pro range of compression fittings with DZR brass bodies for use with copper pipe (EN 1254) Maximum working pressure for 8mm-10mm = 70.0 bar. Maximum working pressure for 12mm – 28mm = 20.0 bar. Maximum working pressure for 35mm – 54mm = 6.0 bar. Maximum operating temperature 90°C.
Range of end feed brass fittings for use with copper tube (manufactured to EN 1057). The HLE20CB-d tank connector incorporates an EPDM washer. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of end feed copper fittings for use with copper tube to EN 1057. The HLDPMFWT and HLDPMFZT models incorporate a captive nut on one end with a fibre gasket washer. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Hydraulic block incorporating heat exchangers with pressed stainless-steel plate bodies and copper brazing. Product also incorporates primary and secondary water way with PPS plastic fittings and adaptors and a flow adjustment valve. Maximum operating temperature: Central Heating Circuit: 90°C, Direct Hot Water Circuit: 65°C. Maximum working pressure: Central Heating Circuit: 2.5 bar, Direct Hot Water Circuit: 10 bar.
Water meter incorporating a stop valve, with plastic body and NBR ‘O’-rings. For use with copper pipe manufactured in accordance with EN1057 and plastic PEX pipe manufactured in accordance with BS7291 Class S. Maximum working pressure 10.0 bar. Cold water use only
Range of aerators with plastic bodies and chrome plated brass housing. Open outlet use only. Maximum operating temperature 65°C
Range of booster pumps with stainless steel bodies, plastic impellers, and NBR ‘O’-rings. The products incorporate a temperature sensor, pressure sensor, pressure vessel and a non-return valve integral to the pump chamber. Maximum working pressure 6.5 bar. Maximum operating temperature 75°C.
Range of self-priming jet pumps with stainless steel bodies. Maximum working pressure 6.0 bar. Maximum operating temperature 45°C
Range of vertical multistage booster pumps, with stainless steel bodies and impellors. Maximum working pressure is either 16.0 or 25.0 bar depending on specific model. Maximum operating temperature 85°C.
‘Matrix’ range of horizontal multistage stage centrifugal booster pumps with stainless steel bodies, stainless steel impellers, EPDM ‘O’-rings and a carbon/ceramic/EPDM mechanical shaft seal. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of single and twin line shower booster pumps with plastic bodies, plastic impellors, stainless steel motor, NBR ‘O’-rings and EPDM seals. Each suction port incorporates a combined EPDM washer and stainless steel strainer. Maximum working pressure 3.0 bar. Maximum operating temperature 65°C.
Range of horizontal self-priming multistage pumps with stainless steel bodies, stainless steel impellers, shaft and outer sleeve. Maximum working pressure 10.0 Bar Maximum operating temperatures: EH Three phase models 85°C, EH Single phase models 55.0°C and EHsp models 35°C.
‘3ME’ Range of horizontal pumps with stainless steel bodies and impellers, and EPDM ‘O’-rings. The products are supplied with a carbon/ceramic/EPDM shaft seal. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Shower kit comprising of a brass bodied wall outlet elbow (chrome plated), TPE lined shower hose (chrome finish) and a brass bodied (chrome plated) shower handset with silicone nozzles. The wall outlet incorporates an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 60°C.
Range of shower outlets with plastic bodies (various finishes) incorporating a stainless-steel strainer and a flow regulator. Maximum operating temperature 60°C.
Range of ceiling tubes for shower heads with brass bodies (various finishes) and EPDM ‘O’-rings. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of overhead shower outlets with stainless steel bodies that incorporates a flow regulator and stainless-steel strainer. Maximum operating temperature 60°C.
Range of shower handsets with plastic bodies (various finishes) incorporating stainless steel strainers on the inlets and flow regulators (on models 26 827 XXX and 26 829 XXX). Maximum operating temperature 60°C.
Range of overhead shower outlets with brass bodies (various finishes), incorporating a plastic strainer at the inlet. Maximum operating temperature 60°C.
Range of shower handsets with either stainless steel or brass bodies (various finishes). Product is supplied with a metal sheathed flexible hose. Maximum operating temperature 60°C.
Page 67 of 201
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
