'Rashmi Cement 43 Grade OPC'. Factory applied, grey coloured Ordinary Portland cement mortar. Mix cement, sand and water in a 1: 1.5: 0.5 ratio. Cure for 28 days@5°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'LSR Soft Touch Coating – Kohler NC001'. Factory applied, three-component, clear silicone coating. Mix coating, catalyst and thinner in a 100:2:500 mass ratio, stir for 10 minutes and then apply. Cure for 10 minutes@160°C, humidity 60%. For use with water up to 70°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'5017 Blue'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions issued January 2020, 'V7.2'. Cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JH'. Factory applied, blue coloured epoxy powder coating. Heat substrate to 220°C for 30 minutes, spray apply coating and then cure at 190°C for 20 minutes. For use with water up to 23°C. This material is only approved for the application and curing conditions that appear on the approval. If the cure and/or application conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘EUROKOTE® 46-20’. Factory applied, red-brown coloured, two-part epoxy resin coating. Mix and apply as per manufacturer's technical data sheet 'Doc. 087' dated 01/07/2011. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
DHDC-7500. Grey coloured, factory applied 2-Part epoxy resin coating. Mix base (A) and hardener (B) in a ratio of 3 (A):1 (B) by weight before applying one coat by airless spray. Cure for 7 days at 25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'CeramycGuard for use with QuartzSeal'. Site applied, white coloured (once mixed) polymer based concrete surface treatment. 'CeramycGuard’ is a three-component base coat comprising of Part A (clear liquid), Part B (grey powder) & Part C (clear liquid). Mix Parts A, B & C in a volume ratio. Rest for two minutes, apply as per manufacturer's instructions for use 'version 2' dated 'April 2021' and then cure for 24 hours@21°C. ‘QuartzSeal' is a white coloured, single-component topcoat. Apply as per manufacturer's instructions for use 'version 2' dated 'April 2021'. Cure for 7 days@21°C. For use with water up to 23°C. These materials are only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Superfast Potable Water (SFPW)'. Site applied, grey coloured (once mixed), two-component epoxy putty. Mix Part A (white coloured putty) with Part B (cream coloured putty) in a 1:1 mass ratio and apply as per manufacturer's instructions 'SOP Number RM1 version 1.0', dated '06/10/2022'. Cure for 24 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'LATTYflon 2790AL'. Cream coloured, PTFE/silicone braided rope with a square cross-section. For use with water up to 23°C. For use only as a gland packing material having been tested at a reduced surface area to volume ratio.
'Solico Ivory GRP Panel'. Beige coloured, compression moulded GRP panel. For use with water up to 60°C.
'JUSTLINK® JLPEX'. Single layered, off-white (translucent), extruded PEX hose. For use with water up to 60°C.
‘4TECH 9G22130 W-A ABK, 4TECH 9G22135 W-A ABK, 4TECH 9G22140 W-A ABK, 4TECH 9G22145 W-A ABK, 4TECH 9G22150 W-A ABK, 4TECH 9G22155 W-A ABK & 4TECH 9G22160 W-A ABK’. Black coloured, glass-fibre reinforced PA66 materials. For use with water up to 23°C.
‘4MID 9A22130 HW-A ABK, 4MID 9A22135 HW-A ABK, 4MID 9A22140 HW-A ABK, 4MID 9A22145 HW-A ABK & 4MID 9A22150 HW-A ABK’. Black coloured, glass-fibre reinforced PA66 materials. For use with water up to 23°C.
'Mapex® AN4920SN FWB50 & GITOP® G3A2 M01FWB'. Black coloured, injection moulded, glass fibre reinforced PA66 materials. For use with water up to 85°C.
'Grilon BG-30/2 natural (appears cream in colour) & Grilon BG-30/2 black 9697 (black coloured)'. Injection moulded PA-GF30 materials. Grilon BG-30/2 black 9697 is for use with water up to 85°C. Between 1st October 2020 and 10th May 2022, Grilon BG-30/2 natural was for use with water up to 23°C. Between 11th May 2022 and 31st October 2025 Grilon BG-30/2 natural is for use with water up to 60°C.
'POLYNT 1349 TAEQ20 to be used in conjunction with POLYCOR LP PA FC CLEAR 0200'. POLYNT 1349 TAEQ20 is a polyester resin and LP PA FC CLEAR 0200 is a factory applied, gel coat (when used together the material appears light pink in colour). Apply as per manufacturer's TDS ‘7206 updated 10.10.17’. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LSPE-BE002 PE Pipe (Deep Blue)'. Blue coloured, extruded polyethylene pipe. For use with water up to 60°C.
'LSPE-BE002 PE Fitting (Deep Blue)'. Blue coloured, injection moulded polyethylene fitting. For use with water up to 60°C.
'LSPE-BK001'. Black coloured, extruded polyethylene pipe. For use with water up to 60°C.
'LSPE-BK001'. Black coloured, injection moulded polyethylene fitting. For use with water up to 60°C.
Page 56 of 584
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
