Range of gate valves with a DZR brass body and disc, and PTFE washers. The products are operated by a non-rising spindle headwork with a hand wheel operating member. For use with copper pipe manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of stop valves with brass bodies and an EPDM washer. 15mm and 22mm for use with half-hard copper pipe of R250 acc. to EN1057. 20mm and 25mm for use with half hard copper pipe of R250 acc. to BS2871-2. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of double regulating valves incorporating bronze bodies, brass disc face (½” - ¾” models) or PTFE (1” - 2” models), PTFE plate and NBR ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of double regulating valves incorporating bronze bodies, brass disc face (½” - ¾” models) or PTFE (1” - 2” models), PTFE plate and NBR ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of regulating valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
‘Tornado’ & ‘Ninjo’ ranges of freestanding and undercounter bedpan washers with flow controlled via a solenoid and discharged via type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 8.0 bar. Maximum operating temperature 60°C
Range of commercial front loading washing machines with flow controlled by solenoid valve and discharged via a type AD air gap arrangement (verified by test - suitable for backflow protection against fluid category 5). The product is supplied with a single check valve assembly (suitable for backflow protection against Fluid Category 2) and PEX lined rubber inlet connections hoses. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of ion exchange water softeners (salt regenerated) for domestic use. Maximum working pressure 6.0 bar. Cold water use only.
'Iupital F10-01'. White coloured, injection moulded POM material. For use with water up to 85°C.
'ABS-001 (natural - appears off-white), ABS-002 (white), ABS-003 (grey), ABS-004 (blue), ABS-005 (green) & ABS-006 (pink)'. Injection moulded ABS (with Biomaster 612 added) materials. For use with water up to 70°C.
‘Inertol BS10’. Factory applied, black coloured bitumen coating. Apply and cure as per manufacturer’s instructions 'BF-T06', issue number '03' dated 01.12.2021. For use with water up to 60°C. Petroleum or asphaltic bitumen, NOT coal tar bitumen. Materials listed in this section are not approved for use for contact with water that is required to be wholesome on large water retaining structures such as lining of pipes, cisterns or water storage tanks.
'Tecnocoat P-2049'. Factory applied, two component, grey coloured polyurea coating. Mix components A & B in a weight ratio of 1:1 and apply as per manufacturer's TDS 'v. 20-03-2022'. Cure for 48 hours@23°C. Between September 2022 and August 2024, the coating is for use with water up to 23°C. From September 2024, the coating is for use with water up to 60°C. This material is only approved for the mixing, curing & soaking conditions that appear on the approval. If the mix/cure/soak conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Relipoxy 342 Food Grade Epoxy Coating'. Factory applied, brown-red coloured epoxy coating. Apply as per manufacturer's 'Standard Operating Procedure & Guidelines' issue number '116/2021' dated 15th Feb 2021. Cure for 24 hours@30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Apcoguard SF 157'. Factory applied, grey coloured, two-component epoxy coating. Mix in a 3:1 volume ratio. Apply as per manufacturer's Application Guidelines 'APPPG/SF157/001' dated 'Jan-2021'. Cure for 7 days@25°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jerlac Two-Pack Epoxy Blue – 746 & Jerlac Two-Pack Epoxy Red – 747'. Factory applied, blue or red coloured, two-component epoxy coatings. Mix resin and hardener in a 3:1 volume ratio and apply as per manufacturer's instructions. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Cementitious Coating 851 White'. Site applied, light grey coloured (once mixed), two-component cementitious coating. Mix Part A (white liquid) with Part B (powder) in a weight ratio of 1:4 then apply in accordance with manufacturer's instructions '851 /031/012' dated 'July 2021'. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Interline 925GF (White)'. Site applied, white coloured, two-component, solvent free epoxy coating. Mix part A (white liquid) with part B (off-white liquid) in a volume ratio of 3:1 and apply as per manufacturer's instructions '2253' dated 29/11/2011. Cure for 7 days@25°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Interline 925 White'. Site applied, two-component, white coloured epoxy coating. Mix part A (off-white white coloured liquid) and part B (off-white coloured liquid) in a volume ratio of 3:1 and apply as per manufacturer's instructions ref. '2252', issue date 17/12/2020. Cure for 7 days@25°C. Between January 2022 and August 2022, the coating was for use with water up to 23°C. Between September 2022 and January 2027, the coating is for use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NO MORE DAMP Tanking slurry'. Site applied, grey coloured, cementitious tanking slurry supplied in powder form. Mix powder:water in a mass ratio of 3.85:1 and apply as per manufacturer's datasheet 'issue 5 - MC0420'. Cure for 7 days and 4 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hydradry Tanking slurry'. Site applied, grey coloured, cementitious tanking slurry supplied in powder form. Mix powder:water in a mass ratio of 3.85:1 and apply as per manufacturer's datasheet 'issue 5 - MC0320'. Cure for 7 days and 4 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Extrastrong SMC/ESF-30-10' pipe. Natural (appears pale green coloured) GRE pipe manufactured by filament winding. For use with water up to 70°C.
'S350 Silicone Fluid'. Colourless (transparent) silicone lubricant. Apply as per manufacturer's instructions for use 'LDAP-009', issue 1 dated May 2021. For use with water up to 85°C.
'SG100'. Off-white coloured (opaque) silicone grease. Apply as per manufacturer's instructions. For use with water up to 65°C.
'SIL500'. Off-white coloured (opaque) silicone grease. Apply as per manufacturer's instructions. For use with water up to 65°C.
`Unisilkon M2000`. Clear, colourless silicone lubricant aerosol. For use with water up to 23°C.
'Rilsan BZM 30 O TLD A'. Beige coloured, injection moulded, glass fibre reinforced nylon material. For use with water up to 85°C.
'Zytel® RSFG30G50L BK595'. Black coloured, injection moulded glass fibre reinforced nylon (polyamide 610) material. For use with water up to 85°C.
'Zytel® FG70G30HSR3 BK309'. Black coloured, injection moulded nylon material. For use with water up to 85°C.
`Grilamid TR 90 LS Natural & Grilamid TR 90 Natural`. Natural (colourless, transparent), injection moulded nylon materials. For use with water up to 85°C.
'Tecomid NB40 GR30 NL HC QW'. Off-white coloured (translucent), injection moulded PA6 material. For use with water up to 85°C.
'Omnix DW 4050 BK 001'. Black coloured, injection moulded PA material (manufactured in Oudenaarde, BE and Changshu, China). For use with water up to 85°C.
'Lasertec PE-RT/Al Multi-layered Pipe'. Extruded PE-RT pipe comprising of a black coloured inner, aluminium barrier layer and silver-grey coloured outer layer. For use with water up to 70°C.
'DBS0420-DBS0640'. Orange coloured HDPE ball float, manufactured by blow moulding. For use with water up to 23°C.
'NAFF ZPE PE40 LDPE'. Black coloured (with blue external stripes), extruded LDPE pipe. For use with water up to 23°C.
'Isoryl A 20 90 GF20 W NA'. Beige coloured, injection moulded PPO material. For use with water up to 85°C.
WOTLON MPPO 1000-GF2 BK006. WOTLON MPPO 1000-GF2 GY003. WOTLON MPPO 1000-GF2 NC001. WOTLON MPPO 1000-GF3 BK006 WOTLON MPPO 1000-GF3 GY003 WOTLON MPPO 1000-GF3 NC001 Natural (NC grades - appears beige in colour), black coloured (BK grades) and grey coloured (GY grades), injection moulded MPPO materials. For use with water up to 85°C.
'Isoglas H30FVL (c) NA'. Translucent, off-white coloured, injection moulded, polypropylene material. For use with water up to 85°C.
'AKORROS® B208A'. Brown coloured, extruded hard rubber Shore hardness 78. Tested in-radius size 1.11mm. For use with water up to 60°C.
'LOPI80 'O'-rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 80. Tested in-radius size 2.26mm. For use with water up to 85°C.
0713.23/60 (shore hardness 60A). 0713.23/65 (shore hardness 65A). 0713.23/70 (shore hardness 70A). 0713.23/75 (shore hardness 75A). 0713.23/80 (shore hardness 80A). 0713.23/85 (shore hardness 85A). Black coloured, compression moulded EPDM rubber materials. Tested in-radius size 1.0mm. For use with water up to 85°C.
'E2532'. Black coloured, compression moulded EPDM material. Shore hardness 55. Tested in-radius size 1.0mm. For use with water up to 23°C.
`SACHDEVA/EPDM-80`. Black coloured, compression moulded EPDM rubber material. Shore hardness 80. Tested in-radius 1.1mm. For use with water up to 23°C.
'VI701/KTW'. Black coloured, injection moulded FKM 'O'-ring, shore hardness 70, tested in-radius 1.5mm. For use with water up to 85°C.
'WN70/3 BLK NBR 'O' rings. Black coloured, injection moulded 'O' rings. Shore hardness 70. Tested in-radius size of 1.0mm For use with water up to 23°C.
'7PD1612 washers'. Black coloured, extruded NBR rubber washers. Tested in-radius size 1.4mm. Shore hardness 70. '7PD1612 'O' rings'. Black coloured, injection moulded NBR rubber `O` rings. Tested in-radius size 0.9mm. Shore hardness 70. Both for use with water up to 60°C.
'CHEMILINE AH001 FB 026'. Black coloured, niltrile rubber material manufactured by calendaring and curing. Shore hardness 70A. Tested in-radius size 1.1mm. For use with water up to 65°C.
‘NGP 60 T (Translucent – off-white), NGP 60 T/R (Transy Red), NGP 60 BK (Black), NGP 60 GY (Grey) & NGP 60 W (White)’. Extruded, platinum cured, silicone rubber tubing. Shore hardness 60. Tested in-radii sizes between 0.75mm & 1.5mm. For use with water up to 85°C
'Tangit PVC-U Plus'. Light yellow (straw) coloured, solvent cement. Apply as per manufacturer's TDS 'Tangit PVC-U PLUS TDS 070917 EN'. Cure for 24 hours@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Bidet seat assembly with the flow controlled by a sensor actuated solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 1.75 bar. Maximum operating temperature 45°C.
Page 50 of 234
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
