Range of ball valves with nickel plated brass bodies, chrome plated brass ball, PTFE seats, and either lever or T handle operating members (see models). Maximum working pressure 16.0 to 64.0 Bar (Size & model dependant, see models) Maximum working temp 85°C
Range of lever operated spherical valves with nickel plated brass or DZR brass bodies, chrome plated brass ball and PTFE seat. Maximum working pressure is 40.0 bar for ¼” to 2” and 25.0 bar for 2½” to 4”. Maximum operating temperature 100°C.
Range of spherical valves (inline, angled and tee) with chrome plated brass bodies and ball. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of spherical valves with nickel plated brass bodies, chromium plated brass balls, PTFE seals, NBR and/or FKM ‘O’-rings. 140, 140M, 141 & 141M series models incorporate a stainless-steel strainer. 140 & 141 series models also incorporate a magnet. The 121 & 122 series models are 3-way valves. Maximum working pressure: See PN in brackets under model. Maximum operating temperature: Cold water use only.
Manifold spherical valve with DZR brass body and ball (chrome plated), incorporating a single lever type operating members and a single check valve assembly (verified by test as suitable for backflow protection against Fluid Category 2). For use with with copper pipe manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with a brass body (chrome plated), stainless steel ball, and PTFE seats and seals. The P472CPBH.1 model is supplied with a copper olive, the P472CPBH.2 model with a brass olive. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of lever operated spherical valves with brass bodies (nickel plated), chrome plated brass balls, and EPDM ‘O’-rings. Compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with a brass body, chrome plated brass ball, and lever operating member. Maximum working pressure 25.0 bar. Maximum operating temperature100°C.
Range of screwdriver operated spherical valves incorporating brass bodies, brass ball, and EPDM ‘O’-rings. Compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical isolation valves incorporating brass bodies (nickel plated), brass ball (chrome plated), brass stem and EPDM ‘O’-rings (screwdriver operated or T-type handle). For use with copper pipe (EN1057). Maximum working pressure 16.0 bar (model 999698) Maximum working pressure 25.0 bar (model 496877) Maximum working pressure 40.0 bar (models 570500 & 570622) Maximum operating temperature 85°C.
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies, and an EPDM wedge, gasket and ‘O’-ring. The MV40-AAAAXY (model has a rising spindle, the MV40-AAAAX model has a non-rising spindle, both have a handwheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies, and an EPDM wedge, gasket and ‘O’-ring. with a a non-rising spindle, both have a handwheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of gate valves with a non-rising spindle and a handwheel operating member with a brass body and brass wedge. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies, and an EPDM wedge, gasket and ‘O’-ring. The RVRX model has a rising spindle, the RVHX model has a non-rising spindle, both have a handwheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of electrolytic water conditioning units consisting of stainless-steel tube with a copper/zinc alloy sacrificial anode and brass inlet and outlet connections. Compression models are for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of ozone cleaning units with a plastic body. The water which is discharged from these units is intended to be used for cleaning surfaces. The products incorporate a filter (cartridge and housing), pressure regulator and a stainless-steel strainer at the inlet. The flow is controlled via a metal solenoid which is operated by a switch on the front panel. Maximum working pressure 5.0 bar. Cold water use only.
Range of ion exchange water softeners (salt regenerated) for domestic use. Maximum working pressure 8.3 bar. Cold water use only.
'DURACON® M25-44 WK2001, M90-44 WK2001 & M270-44-WK2001'. White coloured, injection moulded POM materials. For use with water up to 85°C.
`4300314` (grey coloured) & '4300315' (black coloured). Injection moulded ABS material. For use with water up to 85°C.
'A-95 sealing plate'. White coloured, compression moulded sealing plate. For use with water up to 85°C.
'AO-96 Sealing Ring'. Black coloured, compression moulded, ceramic sealing ring. For use with water up to 85°C.
‘Hexoloy SA & Hexoloy SP’. Dark grey coloured, silicon carbide ceramic component, manufactured by pressing. For use with water up to 85°C.
'T195 NS sealing plate'. White coloured, compression moulded sealing plate. For use with water up to 85°C.
'T11 Sealing Ring'. Black coloured, compression moulded, ceramic sealing ring. For use with water up to 85°C.
'PPA 571 ES Blue 536'. Factory applied, blue coloured polyolefin coating. Apply as per manufacturer's instructions dated '08/2022'. Cure for 20 minutes@200°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Powercron® 451 A – CP 573 B ITT Lowara'. Factory applied, blue coloured cationic resin coating. Apply as per manufacturer's technical data sheet 'LT/I-21-090' dated 'Sep 9, 2021'. Cure for 20 minutes@180°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Eurokote 468 Thixo Brun Rouge 500'. Factory applied, red/brown coloured, two-part epoxy coating consisting of a resin and hardener. Mix resin and hardener in a weight ratio of 70:30 and apply as per manufacturer's Technical Data Sheet version edit '23/01/202. Cure for 10 days@20°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EXCELLUBE B300'. Factory applied, black coloured PTFE (low friction) coating. Apply as per instructions ‘issue 1’, dated 23.01.18. Cure for 20 minutes@240°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PMSP5108-M'. Factory applied, blue coloured enamel coating. Apply as per manufacturer's user manual 'edition 01', dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Apcoflor MFP 140 Primer and Smartcare Polyurea PW Coating'. Factory applied, grey coloured (once mixed), two-component primer (non-water contact primer) and two-component coating (water contact coating). Mix Apcoflor MFP 140 Primer in a 1:1 mix ratio and apply as per Product Data Sheet ‘Version ‘0’, dated ‘Aug.2007’. Cure for 2 hours@25°C. Then mix and apply Smartcare Polyurea PW Coating as per Product Data Sheet ‘V01’, dated ‘8/2022’. Cure for 1 minute@25°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Belzona 5892'. Site applied, epoxy coating consisting of Belzona 5892 (white – Parts A & B) & Belzona 5892 (grey – Parts A & B). Belzona 5892 (white – Parts A & B) are mixed in a weight ratio of 5.7:1 and then applied as a first coat (no cure) in accordance with manufacturer’s instructions for use ‘FN10106’, publication number ’04-11-20(01)’. Belzona 5892 (grey – Parts A & B) are mixed in a weight ratio of 5.7:1 and then applied to the white in accordance with manufacturer’s instructions for use ‘FN10106’, publication number ’04-11-20(01)’. The final coating is then cured for 24 hours@30°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Sikalastic 840 ES'. Site applied, blue coloured, two-component polyurea coating consisting of Component A, Component B and Component C (Pigment Paste). Mix & apply as per manufacturers datasheet dated 16/05/2022. For use with water up to 60°C. This approval is valid only for the material when it is applied by experienced, suitably trained applicators that are authorized and/or certified by Sika UAE L.L.C The authorization, training and certification of the local applicators are the responsibility of Sika UAE L.L.C and not the responsibility of WRAS.
'Cementitious Coating 851 Grey'. Site applied, two part, grey coloured cementitious waterproof mortar which can be applied as a one-coat or two-coat system Mix liquid (Part A) and powder (Part B) in a weight ratio of 1:3.92 and apply as per manufacturer’s instructions 'Bulletin No.851 /031/012' dated July 2021. When using as a one-coat system cure for 21 days@7°C. When using as a two-coat system cure coat one for 1 hour@7°C and cure coat two for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Novatec® Premium XP'. Blue coloured, fibre gasket material. For use with water up to 85°C. For use only as a gasket material having been tested at a reduced surface area to volume ratio.
'Wavistrong EWT Series Pipe'. Yellow/beige coloured, glass fibre reinforced epoxy pipe manufactured using filament (helical) winding. For use with water up to 85°C.
'LZFRP-GE-01'. Green coloured, GRE material manufactured by filament winding. For use with water up to 85°C.
'Berulub FO 34'. White coloured lubricant. For use with water up to 85°C.
'Sapphire Aqua Sil' (translucent, white coloured) & 'Sapphire Aqua Hi Load' (grey coloured). Silicone oil based lubricants. Apply as per manufacturer`s technical data sheet. For use with water up to 85°C.
'FloPlast SG800'. Blue coloured lubricant. Apply as per manufacturer's instructions. No cure required. For use with water up to 23°C.
'Berusoft 30'. White coloured lubricant. Apply as per manufacturer's instructions. For use with water up to 85°C.
'Grilamid LBKN-50H FWA natural, Grilamid LBKN-30H FWA natural, Grilamid LBKN-50H FWA black 9225 & Grilamid LBKN-30H FWA black 9225'. Natural (appears light grey) and black coloured, injection moulded nylon materials. For use with water up to 85°C.
'Radius Systems Light Blue SC80 Pipe'. Extruded, dual layered pipe consisting of a black coloured PE80 inner layer and blue coloured PE80 outer layer. For use with water up to 23°C.
'POLYAOUN non-insulated Water Tank Panel'. LDPE tank panel, made by roto-moulding, comprising of a white coloured inner & outer layer and black coloured middle layer. For use with water up to 85°C.
'POLYAOUN insulated Water Tank Panel'. LDPE tank panel, made by roto-moulding, comprising of white coloured, inner and outer layer, black coloured 2nd layer and grey coloured 3rd layer. For use with water up to 85°C.
'SPS HDPE Pipe'. Black coloured (with blue stripes), extruded PE 100 pipe. For use with water up to 85°C.
'JRG Sanipex MT Multilayer Pipe'. Triple layered, extruded PE-Xc/Al/PE-Xb pipe consisting of a cream coloured inner, aluminium barrier layer and black coloured outer layer. For use with water up to 85°C.
'Weixing HDPE Pipes'. Black (with blue stripe) or blue coloured, extruded HDPE pipes. For use with water up to 23°C. From January 2023 the pipes are suitable for use with water up to 85°C.
'Weixing HDPE Fitting blue'. Blue coloured, injection moulded HDPE fitting. Added in January 2023: 'Weixing HDPE Fitting black'. Black coloured, injection moulded HDPE fitting. For use with water up to 85°C.
'Shield HDPE PE 100 Fittings'. Black coloured, injection moulded PE100 fittings. For use with water up to 85°C.
'PE-BWG'. Transparent, extruded, single layer, polyethylene hose. For use with water up to 85°C.
Page 49 of 158
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
