'HZ-PSU-3'. Natural (appears yellow/brown), injection moulded PSU (polysulphone) material. For use with water up to 85°C.
'Polis PTFE'. White coloured, injection moulded PTFE material. For use with water up to 85°C.
'F801'. White coloured, extruded PTFE material. For use with water up to 85°C.
'F391'. Blue/grey coloured, extruded PTFE material. For use with water up to 85°C.
'F1500'. White coloured, extruded PTFE material. For use with water up to 85°C.
'INOLUB™ T201F, T202F, T203F, T204F & T205F'. White coloured, compression moulded PTFE materials. For use with water up to 85°C.
‘GF PVCU fittings manufactured from HS1013, IR348 & HS1014’. From September 2023 onwards, the fittings may also be made using 'IR 349'. Grey coloured, injection moulded PVC-U fittings. For use with water up to 60°C.
'Dragon STD'. Site applied, off-white coloured, two-part epoxy resin and fibreglass cloth. Mix resin in a 77.8@22.2 volume ratio and apply to the fibreglass cloth. Once the cloth is fully impregnated, apply to the defect as per manufacturer's instructions 'IMG MPW 020' dated 01.07.2022. Cure for 24 hours@21°C or 4 hours@100°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'TIMO 7 NC-70 'O'-rings and washers'. Black coloured, injection moulded EPDM 'O'-rings and washers. Shore hardness 70. Tested in-radius size between 0.5mm & 2.6mm. For use with water up to 85°C.
'MBMS0715'. Black coloured, compression moulded EPDM 'O' ring. Shore hardness 70. Tested in-radius size between 0.25mm and 5.0mm. For use with water up to 85°C.
'EP12/2/5 BLK 'O'-rings & seals'. Black coloured, injection moulded EPDM 'O' rings & seals. Shore hardness 50. The ‘O’ rings have a tested in-radius size of 1.0mm. The seals have a tested in-radius size of 0.75mm. For use with water up to 85°C.
‘4280’ black coloured injection moulded EPDM rubber components. Shore hardness 80. '4280 Membrane' has a tested in-radius size of 1.75mm. ‘4280 ’O’ rings’ have a tested in-radius size of 1.31mm. ‘4280 washers’ have a tested in-radius size of 1.05mm. All components are for use with water up to 85°C.
'TIMO 7 NC-70'. Black coloured, injection moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'AEH-5/EPDM-80'. Black coloured, compression moulded EPDM material. Shore hardness 80.Tested in-radius size 1.1mm. For use with water up to 23°C.
'EP701253C'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'AA7LNZ'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'XR0240012'. Black coloured, compression moulded EPDM material. Shore hardness 40. Tested in-radius size 1.5mm. For use with water up to 85°C.
'XXE03'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.05mm. For use with water up to 85°C.
'RE EP/50, 'RE EP/60, 'RE EP/70 & RE EP/80'. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 80. Tested in-radius size 1.0mm. For use with water up to 60°C.
'Seat Seal S1 & S2'. Black coloured (S2) or white coloured (S1), injection moulded silicone rubber components. Shore hardness 80. Tested in-radius size between 0.65mm & 1.54mm. For use with water up to 85°C.
'SIL50 RED 'O' rings & seals'. Red coloured, injection moulded silicone 'O' rings & seals. Shore hardness 50. The ‘O’ rings have a tested in-radius size of 1.3mm. The seals have a tested in-radius size of 4.2mm. For use with water up to 85°C.
'Gebatout2'. Green coloured, polymer sealing paste. Apply as per manufacturer's instructions, 'version 11' dated 23/09/19. For use with water up to 85°C.
'RC 50'. Purple coloured anaerobic adhesive. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions.
'Spears® FlameGuard® FS-5 One-Step'. Red/brown coloured, liquid solvent cement. Apply as per manufacturer's instructions 'FG-3-0321'. No cure required. For use with water up to 82°C.
'40810813 (3019 THF Free)'. Colourless (transparent) solvent cement. Apply as per manufacturer's fact sheet 'TDS00481' dated 20th July 2018. Cure for between 24 hours and 21 days@7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘PK-HM 8 natural (6145) & PK-VM 8 natural (6146)’. Natural (appear beige in colour), injection moulded polyketone materials. For use with water up to 85°C.
'XFGJ-2022'. Factory applied, grey coloured Portland Cement Mortar. Mix cement, sand and water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue 'X20220228F' dated '2022-2-28'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
Range of stop valves with plastic bodies and an EPDM diaphragm. The valves are operated via a switch located on the valve. The RCL and RPL models can also be operated by a remote switch. The product incorporates a plastic strainer central to the body. All valves are for use with copper pipe (manufactured to BS EN 1057). The PL suffix valves are also for use with PEX pipe (manufactured to BS7291-3). Models added Jan 2025 are for use with PE80 & PE100 pipes manufactured to BS EN 12201:2 at the inlets and the outlets are suitable for PEX pipe manufactured in accordance with BS7291 and copper pipe manufactured in accordance with BS EN 1057. For above ground use only. Maximum working pressure 10.0 bar. Cold water use only.
'6083 black'. Black coloured, injection moulded CIIR rubber material. Shore hardness 50. Tested in-radius size 1.1mm. For use with water up to 70°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (various finishes, see models). Flow is controlled by a solenoid valve activated via an infra-red sensor. The products incorporate a hand dryer feature that are activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The products are supplied with a metal backnut. Maximum working pressure 8.0 bar. Cold water use only.
A range of single-hole, single outlet fixed or swivel electronically controlled tap assemblies with brass bodies in various finishes (see models). Flow is controlled by a solenoid valve activated via an infra-red sensor and a ceramic cartridge with a single lever operating members controlling both the flow and temperature for all models excluding 62816, which uses a mixer to control the temperature only with a single lever operating member. The spout outlets incorporate plastic aerators. All models (excluding AZL10range) incorporate a separate approved check valve cartridge on the inlet, verified by test (suitable for backflow protection against Fluid Category 2), The inlets of all models incorporate stainless steel strainers. Maximum working pressure 5.0 bar Maximum working temperature 60°C.
Range of wall mounted mirrored units incorporating an electronically controlled combination tap assemblies. Flow is controlled via solenoid valve which is actuated by an infra-red sensor. The spout outlets incorporate a plastic aerator. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C.
A range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. These products are supplied with an inline servicing valve integrated with a strainer and single check valve assemblies that has been verified by test for back flow prevention level 2. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) electronically controlled combination tap assembles with brass bodies (various finishes). Flow is controlled via a solenoid valve activated via an infra -red sensor. The temperature is controlled via a ceramic cartridge and a single lever operating member. The inlet adaptor incorporates a single check valve cartridge (verified by test, suitable for backflow protection against fluid category 2). The outlet incorporates a stainless-steel strainer and an aerator. Maximum working pressure 5.0 bar Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) electronically controlled combination tap assembles with brass bodies (various finishes). Flow is controlled via a solenoid valve activated via an infra -red sensor. The temperature is controlled via a ceramic cartridge and a single lever operating member. The spout outlet incorporates a pull-out spray with a plastic aerator. The trigger on the pull-out controls optional spray. The inlet adaptor incorporates a single check valve cartridge (verified by test, suitable for backflow protection against fluid category 2). The outlet incorporates a stainless-steel strainer and an aerator. Maximum working pressure 5.0 bar Maximum operating temperature 60°C.
Range of concealed WC flushing cisterns incorporating a BS 1212-4 side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 3 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only
Range of spring loaded, resilient trim, in-line check valve cartridges, with EPDM seals and O-rings within a brass valve body and plastic insert body. For insertion in pipes and fittings with specifically sized bores. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridges for insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies and NBR O-rings. For insertion into specifically dimensioned bores. Maximum working pressure 10 bar. Maximum operating temperature 85°C.
Range of deck mounted side valve with brass bodies and chrome trim sets. Models PDV030, PDV032, PDV067, PDV068 incorporate quarter turn ceramic disc headworks and models PDV029, PDV031 incorporate half turn ceramic disc headworks with various operating members (See models). Models PDV 031, PVD 032 and PVD 068 are supplied with metal back nuts. Models PDV 029, PDV 030 and PDV 067 are supplied with plastic backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of thermostatic cartridges with plastic bodies and NBR ‘O’-rings. All models incorporate a stainless steel filter. For insertion into specifically dimensioned bores. Maximum working pressure 5.0 bar. Maximum operating temperature 80°C. Maximum operating temperature 60°C for Model 0426AFOC1-001.
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes), incorporating ceramic disc headworks and single lever operating members. The cold inlet to the tap incorporates incorporates an approved check valve cartridge which has been verified by test (as suitable for backflow protection against Fluid Category 2). The inlet of hose to the pull-out spray incorporates an approved check valve cartridge which has not been fully tested to demonstrate it provides backflow protection. The outlet of pull-out spray incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes), incorporating ceramic disc headworks and single lever operating members. The cold inlet to the tap incorporates incorporates an approved check valve cartridge which has been verified by test (as suitable for backflow protection against Fluid Category 2). The inlet of hose to the pull-out spray incorporates an approved check valve cartridge which has not been fully tested to demonstrate it provides backflow protection. The outlet of pull-out spray incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The cold water inlet incorporates an approved check valve cartridge, verified by test (as suitable for backflow protection against Fluid Category 2) The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The inlets incorporate approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products are supplied with a click type pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The product is supplied with a click type waste. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates either a combined EPDM washer and stainless steel strainer with a plastic flow straightener, or an EPDM washer with a plastic aerator. The product is supplied with a click type waste, verified by test. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The product is supplied with optional ⅜” BSP (M) x ½” BSP (F) adaptors each with two fibre gaskets for installation on each inlet hose. The spout outlet incorporates a plastic aerator. The 58005 model is supplied with a pop-up waste. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The product is supplied with or without a pop-up waste or a retractable chain. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes). Incorporating a quarter turn ceramic disc headworks with either single lever, dome or cross-top operating members. The spout outlets incorporate plastic aerators or flow straighteners with a stainless steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Page 44 of 158
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
