'XYRON WG732 AWY2266, WG732 AWY2269, WG732 AWY6628, WG722 AWY6627, W5002 AWY1208, W5002 AWY2267, W5002 AWY6629, W5002 AWY3326, WG722 AWY2261, WG732 AWY3325, WG722 AWY3324 & WG733 ABY3315'. Injection moulded, black, grey or beige coloured PPE materials manufactured in Thailand & China. For use with water up to 85°C.
'Ryton XE-5501BL'. Dark grey coloured, injection moulded PPS material. For use with water up to 23°C.
'Popular PPRC 100 Pipe'. Green coloured, extruded PPR pipe. For use with water up to 60°C.
'ALTECH PP-H FC 3013/500.01 GB13 NC0001-00 (1004864600000)'. Natural (appears white coloured), injection moulded PP-H material. For use with water up to 50°C.
'Hostalen PP H5416T'. White coloured (translucent), extruded polypropylene material. For use with water up to 60°C.
'Hostalen PP H1022 12 (black coloured) & Hostalen PP H1022 (natural - appears white in colour)'. Injection moulded and compression moulded PP materials. For use with water up to 23°C.
'HS 22158'. Grey coloured, compression moulded PTFE material. For use with water up to 85°C.
`Superfast Copper`. Site applied, copper coloured epoxy putty. The putty should be kneaded together, its supplied in a pre-measured 1:1 mass ratio and applied as per manufacturer's directions for use dated August 9th, 2021. Cure for 24 hours@22°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘PX70N-0201 washers, ‘O’ rings, bushes gaskets & discs’. Black coloured, injection moulded EPDM components with a shore hardness of 70. The washers have a tested in-radius size of 3.0mm. The ‘O’ rings have a tested in-radius size of 3.5mm. The bushes gaskets have a tested in-radius size of 2.0mm. The discs have a tested in-radius size of 2.65mm. All are for use with water up to 85°C.
`EP1/1/5 BLK 'O' rings, seals & gaskets'. Black coloured, injection moulded EPDM 'O' rings, seals & gaskets. Shore hardness 70. The 'O' rings & gaskets have a tested in-radius size of 1.5mm. The seals have a tested in-radius size of 0.8mm. For use with water up to 85°C.
'EPDMprx'. Black coloured, injection moulded EPDM material. Shore hardness 78. Tested in-radius size 1.0mm. For use with water up to 85°C.
'60 EPDM 334 black 60 ShA' (shore hardness 60) and '70 EPDM 335 black 70 ShA' (shore hardness 70). Black coloured compression moulded EPDM materials. Tested in-radius 1.07mm. For use with water up to 85°C.
‘40SIL310P, 45SIL310P, 50SIL310P(W), 55SIL310P, 60SIL310P, 65SIL310P, 70SIL310P, 75SIL310P & 80SIL310P'. Compression moulded, silicone rubber ‘O’ rings in natural, white, black, red, blue & yellow with tested in-radii sizes of between 0.5mm & 3.4mm. For use with water up to 85°C.
'1922, 1923 & 1933 washers'. Red coloured, injection moulded silicone rubber washers. 1923 washers have an in-radius of 1.59mm. 1933 washers have an in-radius of 0.83mm. 1922 washers have an in-radius of 1.23mm. For use with water up to 85°C.
'XR0130012 (30SH), XR0140012 (40SH), XR0150012 (50SH), XR0160012 (60SH) & XR0170012 (70SH)'. Translucent, colourless, compression moulded silicone rubber materials. Shore hardness between 30 & 70. Tested in-radius size 1.5mm. For use with water up to 85°C.
'Bondchem WS27'. Anaerobic adhesive which is available in a yellow colour or in a yellow/orange colour. Apply as per manufacturer's instructions and cure for 15 minutes@25°C or 24 hours@22°C. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions.
Bidet seat assembly which discharges via a sensor actuated solenoid valve and utilises a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). The inlet incorporates a strainer and flow regulator. Maximum working pressure 10.0 bar. Cold water supply only.
Range of deck mounted, electronically operated combination tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve which is actuated via an infrared sensor on the spout. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Side entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. Maximum working pressure 10.0 bar. Cold water use only.
Range of bottom entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. The inlet incorporates a plastic strainer. Maximum working pressure 10.0 Bar. Cold water use only.
Page 44 of 508
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
