'PlumbRight' range of push-fit fittings with PEX-b, polysulphone or PPE bodies, supplied with polysulphone inserts. For use with PEX pipe (manufactured to BSEN 7291 part 3), PB (manufactured to BSEN 7291 part 2) and copper pipe. Maximum working pressure 12.5 bar. Cold water use only.

Section:

1180 Fittings for use with Tube and Pipe

Section Subtitle:

Couplings. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

250602052

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

10mm, 15mm, 22mm, 28mm

Marking:

TLC (TwistLoc logo) and size on body

Installation Requirements:

R001

Expiry date:

30/06/2030

Model:

'PlumbRight' range comprising of models: SRDE6764M 15mmX1/2"BSP DROP EAR ELBOW SRF6764M 15mmX1/2"BSP FEMALE ADAPTOR SRF6765M 15mmX3/4"BSP FEMALE ADAPTOR SRF6745M 22mmX3/4"BSP FEMALE ADAPTOR SRF6701M 28mmX1"BSP FEMALE ADAPTOR SPU6711M 10mm STR UNION SPU6766M 15mm STR UNION SPU6744M 22mm STR UNION SPU6700M 28mm STR UNION SPU6761M 15mmX10mm REDUCING STR UNION SPU6746M 22mmX15mm REDUCING STR UNION SRSE6714M 10mmX1/2"BSP SWIVEL ELBOW (Hand Tighten) SRSE6764M 15mmX1/2"BSP SWIVEL ELBOW (Hand Tighten) SRSE6765M 15mmX3/4"BSP SWIVEL ELBOW (Hand Tighten) SRSE6714BM 10mmX1/2"BSP SWIVEL ELBOW (Brass Nut) SRSE6764BM 15mmX1/2"BSP SWIVEL ELBOW (Brass Nut) SRSE6765BM 15mmX3/4"BSP SWIVEL ELBOW (Brass Nut) SPSU6714M 10mmX1/2"BSP SWIVEL UNION (Hand Tighten) SRSU6764M 15mmX1/2"BSP SWIVEL UNION (Hand Tighten) SRSU6765M 15mmX3/4"BSP SWIVEL UNION (Hand Tighten) SPSU6745M 22mmX3/4"BSP SWIVEL UNION (Hand Tighten) SPSU6714BM 10mmX1/2"BSP SWIVEL UNION (Brass Nut) SRSU6764BM 15mmX1/2"BSP SWIVEL UNION (Brass Nut) SRSU6765BM 15mmX3/4"BSP SWIVEL UNION (Brass Nut) SPSU6745BM 22mmX3/4"BSP SWIVEL UNION (Brass Nut) SPST671M 10mm END STOP SPST676M 15mm END STOP SPST674M 22mm END STOP SRST670M 28mm END STOP SPE6711M 10mm ELBOW SPE6766M 15mm ELBOW SPE6744M 22mm ELBOW SPE6700M 28mm ELBOW SPE6761M 15mmX10mm REDUCING ELBOW SPE6746M 22mmX15mm REDUCING ELBOW SPATE6766M 15mm-135o STEM ELBOW SPATE6744M 22mm-135o STEM ELBOW SPR6716M 10mmX15mm REDUCER SPR6764M 15mmX22mm REDUCER SPR6760M 15mmX28mm REDUCER SPR6740M 22mmX28mm REDUCER SPT67111M 10mm TEE SPT67666M 15mm TEE SPT67444M 22mm TEE SPT67000M 28mm TEE SPT67611M 15mmX10mmX10mm REDUCING TEE SPT67661M 15mmX15mmX10mm REDUCING TEE SPT67664M 15mmX15mmX22mm REDUCING TEE SPT67466M 22mmX15mmX15mm REDUCING TEE SPT67464M 22mmx15mmx22mm REDUCING TEE SPT67441M 22mmx22mmx10mm REDUCING TEE SPT67446M 22mmX22mmX15mm REDUCING TEE SPT67044M 28mmX22mmX22mm REDUCING TEE SPT67040M 28mmX22mmX28mm REDUCING TEE SPT67001M 28mmX28mmX10mm REDUCING TEE SPT67006M 28mmX28mmX15mm REDUCING TEE SPT67004M 28mmX28mmX22mm REDUCING TEE SPTT67441M 22mX22mmX10mm TUBE TEE SPTT67446M 22mX22mmX15mm TUBE TEE SPTE6711M 10mm TUBE ELBOW SPTE6716M 10mmx15mm TUBE ELBOW SPTE6766M 15mm TUBE ELBOW SPTE6744M 22mm TUBE ELBOW SRMC6764M 15mmX1/2"BSPT MALE CONNECTOR SRME6764M 15mmX1/2"BSPT MALE ELBOW SRFWC6741M 22mmX10mm 4WAY MANIFOLD SRU6766SM 15mm SLIP UNION SRU6744SM 22mm SLIP UNION STS10M 10mm PIPE INSERT STS15M 15mm PIPE INSERT STS22M 22mm PIPE INSERT STS28M 28mm PIPE INSERT SRAV63M 15mm AIR-VENT CONNECTOR

Approval Holder:

City Plumbing

Company Name

City Plumbing

Address

Highbourne House, 1 Eldon Way, Crick, Northamptonshire

Postcode

NN6 7SL

View All Listings by this Company

Manufacturer:

SNC Corporation

Company Name

SNC Corporation

Address

30, Baekbeom-ro, 678 beon-gil, Seo-gu, Incheon

Postcode

22825

Country

South Korea

Phone

+82-70-8795-3200

View All Listings by this Company

“D-“ and “E-“ range of 304 and 316L stainless steel press fittings, in either ‘M’ press profile (D- prefix models) or ‘V’ press profile (E- prefix models) for use with stainless steel pipe (316L & 304 manufactured to EN10312). For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature: 85°C.

Section:

1180 Fittings for use with Tube and Pipe

Section Subtitle:

Couplings. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

250912029

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See model.

Marking:

Company logo “WEGS”, size, material SUS304 or SUS316L on body.

Installation Requirements:

R001

Expiry date:

30/09/2030

Model:

D-DN10 - 90° Equal Elbow: 15mm, D-DN15 - 90° Equal Elbow: 18mm, D-DN20 - 90° Equal Elbow: 22mm, D-DN25 - 90° Equal Elbow: 28mm, D-DN32 - 90° Equal Elbow: 35mm, D-DN40 - 90° Equal Elbow: 42mm, D-DN50 - 90° Equal Elbow: 54mm, D-DN10 - 90° B-type equal elbow: 15mm, D-DN15 - 91° B-type equal elbow: 18mm, D-DN20 - 92° B-type equal elbow: 22mm, D-DN25 - 93° B-type equal elbow: 28mm, D-DN32 - 94° B-type equal elbow: 35mm, D-DN40 - 95° B-type equal elbow: 42mm, D-DN50 - 96° B-type equal elbow: 54mm, D-DN15×10 - 90° Reducing Elbow: 15×18mm, D-DN20×15 - 91° Reducing Elbow: 22×18mm, D-DN25×15 - 92° Reducing Elbow: 28×18mm, D-DN25×20 - 93° Reducing Elbow: 28×22mm, D-DN10×½ - 90° Male Elbow: 15mm×½, D-DN10×¾ - 90° Male Elbow: 15mm×¾, D-DN15×½ - 90° Male Elbow: 18mm×½, D-DN15×¾ - 90° Male Elbow: 18mm×¾, D-DN20×¾ - 90° Male Elbow: 22mm×¾, D-DN25×1 - 90° Male Elbow: 28 mm×1, D-DN32×1¼ - 90° Male Elbow: 35mm×1¼, D-DN40×1½ - 90° Male Elbow: 42mm×1½, D-DN50×2 - 90° Male Elbow: 54mm×2, D-DN10×½ - 90° female elbow: 15mm×½, D-DN10×¾ - 90° female elbow: 15mm×¾, D-DN15×½ - 90° female elbow: 18mm×½, D-DN15×¾ - 90° female elbow: 18mm×¾, D-DN20×¾ - 90° female elbow: 22mm×¾, D-DN25×1 - 90° female elbow: 28 mm×1, D-DN32×1¼ - 90° female elbow: 35mm×1¼, D-DN40×1½ - 90° female elbow: 42mm×1½, D-DN50×2 - 90° female elbow: 54 mm×2, D-DN10 - 45° Equal Elbow: 15mm, D-DN15 - 45° Equal Elbow: 18mm, D-DN20 - 45° Equal Elbow: 22mm, D-DN25 - 45° Equal Elbow: 28mm, D-DN32 - 45° Equal Elbow: 35mm, D-DN40 - 45° Equal Elbow: 42mm, D-DN50 - 45° Equal Elbow: 54mm, D-DN10 - 45° B-type equal elbow: 15mm, D-DN15 - 45° B-type equal elbow: 18mm, D-DN20 - 45° B-type equal elbow: 22mm, D-DN25 - 45° B-type equal elbow: 28mm, D-DN32 - 45° B-type equal elbow: 35mm, D-DN40 - 45° B-type equal elbow: 42mm, D-DN50 - 45° B-type equal elbow: 54mm, D-DN10 - Equal tee: 15mm, D-DN15 - Equal tee: 18mm, D-DN20 - Equal tee: 22mm, D-DN25 - Equal tee: 28mm, D-DN32 - Equal tee: 35mm, D-DN40 - Equal tee: 42mm, D-DN50 - Equal tee: 54mm, D-DN15×10 - Reducing Tee: 18×15mm, D-DN20×10 - Reducing Tee: 22×15mm, D-DN20×15 - Reducing Tee: 22×18mm, D-DN25×10 - Reducing Tee: 28×15mm, D-DN25×15 - Reducing Tee: 28×18mm, D-DN25×20 - Reducing Tee: 28×22mm, D-DN32×10 - Reducing Tee: 35×15mm, D-DN32×15 - Reducing Tee: 35×18mm, D-DN32×20 - Reducing Tee: 35×22mm, D-DN32×25 - Reducing Tee: 35×28mm, D-DN40×15 - Reducing Tee: 42×18mm, D-DN40×20 - Reducing Tee: 42×22mm, D-DN40×25 - Reducing Tee: 42×28mm, D-DN40×32 - Reducing Tee: 42×35mm, D-DN50×20 - Reducing Tee: 54×22mm, D-DN50×25 - Reducing Tee: 54×28mm, D-DN50×32 - Reducing Tee: 54×35mm, D-DN50×40 - Reducing Tee: 54×42mm, D-DN10×½ - Short elbow with female: 15mm×½, D-DN10×¾ - Short elbow with female: 15mm×¾, D-DN15×½ - Short elbow with female: 18mm×½, D-DN15×¾ - Short elbow with female: 18mm×¾, D-DN20×¾ - Short elbow with female: 22mm×¾, D-DN25×½ - Short elbow with female: 28mm×½, D-DN25×¾ - Short elbow with female: 28mm×¾, D-DN25×1 - Short elbow with female: 28mm×1, D-DN10×½ - Female Tee: 15mm×½, D-DN10×¾ - Female Tee: 15mm×¾, D-DN15×½ - Female Tee: 18mm×½, D-DN15×¾ - Female Tee: 18mm×¾, D-DN20×½ - Female Tee: 22mm×½, D-DN20×¾ - Female Tee: 22mm×¾, D-DN25×½ - Female Tee: 28mm×½, D-DN25×¾ - Female Tee: 28mm×¾, D-DN25×1 - Female Tee: 28 mm×1, D-DN32×½ - Female Tee: 35mm×½, D-DN32×¾ - Female Tee: 35mm×¾, D-DN32×1¼ - Female Tee: 35mm×1¼, D-DN40×½ - Female Tee: 42mm×½, D-DN40×¾ - Female Tee: 42mm×¾, D-DN40×1¼ - Female Tee: 42mm×1¼, D-DN40×1½ - Female Tee: 42mm×1½, D-DN50×½ - Female Tee: 54mm×½, D-DN50×¾ - Female Tee: 54mm×¾, D-DN50×2 - Female Tee: 54mm×2, D-DN10×½ - Male Tee: 15mm×½, D-DN10×¾ - Male Tee: 15mm×¾, D-DN15×½ - Male Tee: 18mm×½, D-DN15×¾ - Male Tee: 18mm×¾, D-DN20×½ - Male Tee: 22mm×½, D-DN20×¾ - Male Tee: 22mm×¾, D-DN25×½ - Male Tee: 28mm×½, D-DN25×¾ - Male Tee: 28mm×¾, D-DN25×1 - Male Tee: 28 mm×1, D-DN32×½ - Male Tee: 35mm×½, D-DN32×¾ - Male Tee: 35mm×¾, D-DN32×1¼ - Male Tee: 35mm×1¼, D-DN40×½ - Male Tee: 42mm×½, D-DN40×¾ - Male Tee: 42mm×¾, D-DN40×1¼ - Male Tee: 42mm×1¼, D-DN40×1½ - Male Tee: 42mm×1½, D-DN50×½ - Male Tee: 54mm×½, D-DN50×¾ - Male Tee: 54mm×¾, D-DN50×2 - Male Tee: 54 mm×2, D-DN10×½ - Male Adapter: 15mm×½, D-DN10×¾ - Male Adapter: 15mm×¾, D-DN15×½ - Male Adapter: 18mm×½, D-DN15×¾ - Male Adapter: 18mm×¾, D-DN20×½ - Male Adapter: 22mm×½, D-DN20×¾ - Male Adapter: 22mm×¾, D-DN20×1 - Male Adapter: 22mm×1, D-DN25×¾ - Male Adapter: 28mm×¾, D-DN25×1 - Male Adapter: 28mm×1, D-DN32×1 - Male Adapter: 35 mm×1, D-DN32×1¼ - Male Adapter: 35mm×1¼, D-DN40×1½ - Male Adapter: 42mm×1½, D-DN50×2 - Male Adapter: 54 m×2, D-DN10 - Equal coupling: 15mm, D-DN15 - Equal coupling: 18mm, D-DN20 - Equal coupling: 22mm, D-DN25 - Equal coupling: 28mm, D-DN32 - Equal coupling: 35mm, D-DN40 - Equal coupling: 42mm, D-DN50 - Equal coupling: 54mm, D-DN15×10 - Reducing coupling: 18×15mm, D-DN20×10 - Reducing coupling: 22×15mm, D-DN20×15 - Reducing coupling: 22×18mm, D-DN25×10 - Reducing coupling: 28×15mm, D-DN25×15 - Reducing coupling: 28×18mm, D-DN25×20 - Reducing coupling: 28×22mm, D-DN32×15 - Reducing coupling: 35×18mm, D-DN32×20 - Reducing coupling: 35×22mm, D-DN32×25 - Reducing coupling: 35×28mm, D-DN40×15 - Reducing coupling: 42×18mm, D-DN40×20 - Reducing coupling: 42×22mm, D-DN40×25 - Reducing coupling: 42×28mm, D-DN40×32 - Reducing coupling: 42×35mm, D-DN50×15 - Reducing coupling: 54×18mm, D-DN50×20 - Reducing coupling: 54×22mm, D-DN50×25 - Reducing coupling: 54×28mm, D-DN50×32 - Reducing coupling: 54×35mm, D-DN50×40 - Reducing coupling: 54×42mm, D-DN10×½ - Female Adapter: 15mm×½, D-DN10×¾ - Female Adapter: 15mm×¾, D-DN15×½ - Female Adapter: 18mm×½, D-DN15×¾ - Female Adapter: 18mm×¾, D-DN20×½ - Female Adapter: 22mm×½, D-DN20×¾ - Female Adapter: 22mm×¾, D-DN25×½ - Female Adapter: 28mm×½, D-DN25×¾ - Female Adapter: 28mm×¾, D-DN25×1 - Female Adapter: 28mm×1, D-DN32×1¼ - Female Adapter: 35mm×1¼, D-DN40×1½ - Female Adapter: 42mm×1½, D-DN50×2 - Female Adapter: 54mm×2, D-DN10×½ - Moving Female Adapter: 15mm×½, D-DN10×¾ - Moving Female Adapter: 15mm×¾, D-DN15×½ - Moving Female Adapter: 18mm×½, D-DN15×¾ - Moving Female Adapter: 18mm×¾, D-DN20×½ - Moving Female Adapter: 22mm×½, D-DN20×¾ - Moving Female Adapter: 22mm×¾, D-DN25×1 - Moving Female Adapter: 28 mm×1, D-DN32×1¼ - Moving Female Adapter: 35mm×1¼, D-DN40×1½ - Moving Female Adapter: 42mm×1½, D-DN50×2 - Moving Female Adapter: 54 mm×2, D-DN10 - Slip coupling: 15mm, D-DN15 - Slip coupling: 18mm, D-DN20 - Slip coupling: 22mm, D-DN25 - Slip coupling: 28mm, D-DN32 - Slip coupling: 35mm, D-DN40 - Slip coupling: 42mm, D-DN50 - Slip coupling: 54mm, DN10×½ - Hexagonal male connector: 15mm×½, DN10×¾ - Hexagonal male connector: 15mm×¾, DN15×½ - Hexagonal male connector: 18 mm×½, DN20×¾ - Hexagonal male connector: 22 mm×¾, DN25×1 - Hexagonal male connector: 28mm×1, DN32×1¼ - Hexagonal male connector: 35 mm×1¼, DN40×1½ - Hexagonal male connector: 42mm×1½, DN50×2 - Hexagonal male connector: 54mm×2, D-DN10 - Caps: 15mm, D-DN15 - Caps: 18mm, D-DN20 - Caps: 22mm, D-DN25 - Caps: 28mm, D-DN32 - Caps: 35mm, D-DN40 - Caps: 42mm, D-DN50 - Caps: 54mm, DN15 - Straight Tube Fittings: 18mm, DN20 - Straight Tube Fittings: 22mm, DN25 - Straight Tube Fittings: 28mm, DN10 - Layflat bridge: 15mm, DN15 - Layflat bridge: 18mm, DN20 - Layflat bridge: 22mm, DN25 - Layflat bridge: 28mm, D-DN25 - Flange adapters: 28mm, D-DN32 - Flange adapters: 35mm, D-DN40 - Flange adapters: 42mm, D-DN50 - Flange adapters: 54mm.

E-DN10 - 90° Equal Elbow: 15mm, E-DN15 - 90° Equal Elbow: 18mm, E-DN20 - 90° Equal Elbow: 22mm, E-DN25 - 90° Equal Elbow: 28mm, E-DN32 - 90° Equal Elbow: 35mm, E-DN40 - 90° Equal Elbow: 42mm, E-DN50 - 90° Equal Elbow: 54mm, E-DN10 - 90° B-type equal elbow: 15mm, E-DN15 - 90° B-type equal elbow: 18mm, E-DN20 - 90° B-type equal elbow: 22mm, E-DN25 - 90° B-type equal elbow: 28mm, E-DN32 - 90° B-type equal elbow: 35mm, E-DN40 - 90° B-type equal elbow: 42mm, E-DN50 - 90° B-type equal elbow: 54mm, E-DN15×10 - 90° Reducing Elbow: 15×18mm, E-DN20×15 - 90° Reducing Elbow: 22×18mm, E-DN25×15 - 90° Reducing Elbow: 28×18mm, E-DN25×20 - 90° Reducing Elbow: 28×22mm, E-DN10×½ - 90° Male Elbow: 15mm×½, E-DN10×¾ - 90° Male Elbow: 15mm×¾, E-DN15×½ - 90° Male Elbow: 18mm×½, E-DN15×¾ - 90° Male Elbow: 18mm×¾, E-DN20×¾ - 90° Male Elbow: 22mm×¾, E-DN25×1 - 90° Male Elbow: 28 mm×1, E-DN32×1¼ - 90° Male Elbow: 35mm×1¼, E-DN40×1½ - 90° Male Elbow: 42mm×1½, E-DN50×2 - 90° Male Elbow: 54mm×2, E-DN10×½ - 90° female elbow: 15mm×½, E-DN10×¾ - 90° female elbow: 15mm×¾, E-DN15×½ - 90° female elbow: 18mm×½, E-DN15×¾ - 90° female elbow: 18mm×¾, E-DN20×¾ - 90° female elbow: 22mm×¾, E-DN25×1 - 90° female elbow: 28 mm×1, E-DN32×1¼ - 90° female elbow: 35mm×1¼, E-DN40×1½ - 90° female elbow: 42mm×1½, E-DN50×2 - 90° female elbow: 54 mm×2, E-DN10 - 45° Equal Elbow: 15mm, E-DN15 - 45° Equal Elbow: 18mm, E-DN20 - 45° Equal Elbow: 22mm, E-DN25 - 45° Equal Elbow: 28mm, E-DN32 - 45° Equal Elbow: 35mm, E-DN40 - 45° Equal Elbow: 42mm, E-DN50 - 45° Equal Elbow: 54mm, E-DN10 - 45° B-type equal elbow: 15mm, E-DN15 - 45° B-type equal elbow: 18mm, E-DN20 - 45° B-type equal elbow: 22mm, E-DN25 - 45° B-type equal elbow: 28mm, E-DN32 - 45° B-type equal elbow: 35mm, E-DN40 - 45° B-type equal elbow: 42mm, E-DN50 - 45° B-type equal elbow: 54mm, E-DN10 - Equal tee: 15mm, E-DN15 - Equal tee: 18mm, E-DN20 - Equal tee: 22mm, E-DN25 - Equal tee: 28mm, E-DN32 - Equal tee: 35mm, E-DN40 - Equal tee: 42mm, E-DN50 - Equal tee: 54mm, E-DN15×10 - Reducing Tee: 18×15mm, E-DN20×10 - Reducing Tee: 22×15mm, E-DN20×15 - Reducing Tee: 22×18mm, E-DN25×10 - Reducing Tee: 28×15mm, E-DN25×15 - Reducing Tee: 28×18mm, E-DN25×20 - Reducing Tee: 28×22mm, E-DN32×10 - Reducing Tee: 35×15mm, E-DN32×15 - Reducing Tee: 35×18mm, E-DN32×20 - Reducing Tee: 35×22mm, E-DN32×25 - Reducing Tee: 35×28mm, E-DN40×15 - Reducing Tee: 42×18mm, E-DN40×20 - Reducing Tee: 42×22mm, E-DN40×25 - Reducing Tee: 42×28mm, E-DN40×32 - Reducing Tee: 42×35mm, E-DN50×20 - Reducing Tee: 54×22mm, E-DN50×25 - Reducing Tee: 54×28mm, E-DN50×32 - Reducing Tee: 54×35mm, E-DN50×40 - Reducing Tee: 54×42mm, E-DN10×½ - Short elbow with female: 15mm×½, E-DN10×¾ - Short elbow with female: 15mm×¾, E-DN15×½ - Short elbow with female: 18mm×½, E-DN15×¾ - Short elbow with female: 18mm×¾, E-DN20×¾ - Short elbow with female: 22mm×¾, E-DN25×½ - Short elbow with female: 28mm×½, E-DN25×¾ - Short elbow with female: 28mm×¾, E-DN25×1 - Short elbow with female: 28mm×1, E-DN10×½ - Female Tee: 15mm×½, E-DN10×¾ - Female Tee: 15mm×¾, E-DN15×½ - Female Tee: 18mm×½, E-DN15×¾ - Female Tee: 18mm×¾, E-DN20×½ - Female Tee: 22mm×½, E-DN20×¾ - Female Tee: 22mm×¾, E-DN25×½ - Female Tee: 28mm×½, E-DN25×¾ - Female Tee: 28mm×¾, E-DN25×1 - Female Tee: 28 mm×1, E-DN32×½ - Female Tee: 35mm×½, E-DN32×¾ - Female Tee: 35mm×¾, E-DN32×1¼ - Female Tee: 35mm×1¼, E-DN40×½ - Female Tee: 42mm×½, E-DN40×¾ - Female Tee: 42mm×¾, E-DN40×1¼ - Female Tee: 42mm×1¼, E-DN40×1½ - Female Tee: 42mm×1½, E-DN50×½ - Female Tee: 54mm×½, E-DN50×¾ - Female Tee: 54mm×¾, E-DN50×2 - Female Tee: 54mm×2, E-DN10×½ - Male Tee: 15mm×½, E-DN10×¾ - Male Tee: 15mm×¾, E-DN15×½ - Male Tee: 18mm×½, E-DN15×¾ - Male Tee: 18mm×¾, E-DN20×½ - Male Tee: 22mm×½, E-DN20×¾ - Male Tee: 22mm×¾, E-DN25×½ - Male Tee: 28mm×½, E-DN25×¾ - Male Tee: 28mm×¾, E-DN25×1 - Male Tee: 28 mm×1, E-DN32×½ - Male Tee: 35mm×½, E-DN32×¾ - Male Tee: 35mm×¾, E-DN32×1¼ - Male Tee: 35mm×1¼, E-DN40×½ - Male Tee: 42mm×½, E-DN40×¾ - Male Tee: 42mm×¾, E-DN40×1¼ - Male Tee: 42mm×1¼, E-DN40×1½ - Male Tee: 42mm×1½, E-DN50×½ - Male Tee: 54mm×½, E-DN50×¾ - Male Tee: 54mm×¾, E-DN50×2 - Male Tee: 54 mm×2, E-DN10×½ - Male Adapter: 15mm×½, E-DN10×¾ - Male Adapter: 15mm×¾, E-DN15×½ - Male Adapter: 18mm×½, E-DN15×¾ - Male Adapter: 18mm×¾, E-DN20×½ - Male Adapter: 22mm×½, E-DN20×¾ - Male Adapter: 22mm×¾, E-DN20×1 - Male Adapter: 22mm×1, E-DN25×¾ - Male Adapter: 28mm×¾, E-DN25×1 - Male Adapter: 28mm×1, E-DN32×1 - Male Adapter: 35 mm×1, E-DN32×1¼ - Male Adapter: 35mm×1¼, E-DN40×1½ - Male Adapter: 42mm×1½, E-DN50×2 - Male Adapter: 54 m×2, E-DN10 - Equal coupling: 15mm, E-DN15 - Equal coupling: 18mm, E-DN20 - Equal coupling: 22mm, E-DN25 - Equal coupling: 28mm, E-DN32 - Equal coupling: 35mm, E-DN40 - Equal coupling: 42mm, E-DN50 - Equal coupling: 54mm, E-DN15×10 - Reducing coupling: 18×15mm, E-DN20×10 - Reducing coupling: 22×15mm, E-DN20×15 - Reducing coupling: 22×18mm, E-DN25×10 - Reducing coupling: 28×15mm, E-DN25×15 - Reducing coupling: 28×18mm, E-DN25×20 - Reducing coupling: 28×22mm, E-DN32×15 - Reducing coupling: 35×18mm, E-DN32×20 - Reducing coupling: 35×22mm, E-DN32×25 - Reducing coupling: 35×28mm, E-DN40×15 - Reducing coupling: 42×18mm, E-DN40×20 - Reducing coupling: 42×22mm, E-DN40×25 - Reducing coupling: 42×28mm, E-DN40×32 - Reducing coupling: 42×35mm, E-DN50×15 - Reducing coupling: 54×18mm, E-DN50×20 - Reducing coupling: 54×22mm, E-DN50×25 - Reducing coupling: 54×28mm, E-DN50×32 - Reducing coupling: 54×35mm, E-DN50×40 - Reducing coupling: 54×42mm, E-DN10×½ - Female Adapter: 15mm×½, E-DN10×¾ - Female Adapter: 15mm×¾, E-DN15×½ - Female Adapter: 18mm×½, E-DN15×¾ - Female Adapter: 18mm×¾, E-DN20×½ - Female Adapter: 22mm×½, E-DN20×¾ - Female Adapter: 22mm×¾, E-DN25×½ - Female Adapter: 28mm×½, E-DN25×¾ - Female Adapter: 28mm×¾, E-DN25×1 - Female Adapter: 28mm×1, E-DN32×1¼ - Female Adapter: 35mm×1¼, E-DN40×1½ - Female Adapter: 42mm×1½, E-DN50×2 - Female Adapter: 54mm×2, E-DN10×½ - Moving Female Adapter: 15mm×½, E-DN10×¾ - Moving Female Adapter: 15mm×¾, E-DN15×½ - Moving Female Adapter: 18mm×½, E-DN15×¾ - Moving Female Adapter: 18mm×¾, E-DN20×½ - Moving Female Adapter: 22mm×½, E-DN20×¾ - Moving Female Adapter: 22mm×¾, E-DN25×1 - Moving Female Adapter: 28 mm×1, E-DN32×1¼ - Moving Female Adapter: 35mm×1¼, E-DN40×1½ - Moving Female Adapter: 42mm×1½, E-DN50×2 - Moving Female Adapter: 54 mm×2, E-DN10 - Slip coupling: 15mm, E-DN15 - Slip coupling: 18mm, E-DN20 - Slip coupling: 22mm, E-DN25 - Slip coupling: 28mm, E-DN32 - Slip coupling: 35mm, E-DN40 - Slip coupling: 42mm, E-DN50 - Slip coupling: 54mm, E-DN10 - Caps: 15mm, E-DN15 - Caps: 18mm, E-DN20 - Caps: 22mm, E-DN25 - Caps: 28mm, E-DN32 - Caps: 35mm, E-DN40 - Caps: 42mm, E-DN50 - Caps: 54mm, E-DN25 - Flange adapters: 28mm, E-DN32 - Flange adapters: 35mm, E-DN40 - Flange adapters: 42mm, E-DN50 - Flange adapters: 54mm.

Product Images

Approval Holder:

Wegs Hubei Fluid Technology Co., Ltd

Company Name

Wegs Hubei Fluid Technology Co., Ltd

Address

Intersection of Xiyuan 7th Road and Xiyuan 10th Road, Phase III, Hitech Development Zone, Xianning City, Hubei Province

Country

China

View All Listings by this Company

Manufacturer:

Wegs Hubei Fluid Technology Co., Ltd

Company Name

Wegs Hubei Fluid Technology Co., Ltd

Address

Intersection of Xiyuan 7th Road and Xiyuan 10th Road, Phase III, Hitech Development Zone, Xianning City, Hubei Province

Country

China

View All Listings by this Company

Range of pre-assembled hydraulic blocks incorporating plate heat exchangers, pressure relief valves set at 3.0 bar, circulation pumps and flow regulators. Maximum working pressure: Primary 2.5bar & secondary 10 bar. Maximum operating temperature 80°C (CH) & 60°C (DHW).

Section:

1350 Heat Exchangers

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

15mm & 22mm Compression.

Marking:

Bosch, model code and other technical information on adhesive label on assembly.

Installation Requirements:

R001

Expiry date:

30/09/2030

Model:

8-718-684-683.

Approval Holder:

Bosch Thermotechnology Ltd.

Company Name

Bosch Thermotechnology Ltd.

Address

Danesmoor Works Pilsley Clay Cross Chesterfield Derbyshire

Postcode

S45 9BY

View All Listings by this Company

Manufacturer:

Bosch Thermotechnik GmbH

Company Name

Bosch Thermotechnik GmbH

Address

Sophienstrasse 30 - 32 D-35576 Wetzlar Germany

View All Listings by this Company

Range of floor-standing gas combination boilers, supplied with isolation valves, expansion vessel and a pressure relief valve set at 3.0 bar. Maximum working pressure: Primary circuit 2.5 bar, secondary 10 bar. Maximum operating temperature: Primary 82°C / secondary circuit 60°C.

Section:

1465 Heaters

Section Subtitle:

Combination boilers and Water Jacketed Tube heaters. Low volume water content. Heat retained in water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within the system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.

WRAS Approval Number:

250904711

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

22mm compression.

Marking:

Worcester on front cover. Worcester and product info on label inside cover.

Installation Requirements:

R001 R140 R360

Expiry date:

30/09/2030

Model:

7-731-600-297 Greenstar 8000F 35kW Combi NG, 7-731-600-298 Greenstar 8000F 35kW Combi LPG, 7-731-600-299 Greenstar 8000F 50kW Combi NG, 7-731-600-300 Greenstar 8000F 50kW Combi LPG.

Approval Holder:

Bosch Thermotechnology Ltd.

Company Name

Bosch Thermotechnology Ltd.

Address

Danesmoor Works Pilsley Clay Cross Chesterfield Derbyshire

Postcode

S45 9BY

View All Listings by this Company

Range of water meters with brass bodies. The inlet incorporates a plastic strainer. Maximum working pressure 16.0 bar. Maximum operating temperature is 50°C or 85°C, please refer to model.

Section:

1505 Water Meters

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

¾” BSP (M) or 1” BSP (M)

Marking:

APATOR, date of manufacture (YYYY) and product information on face of water meter. Flow arrow on body.

Installation Requirements:

R001

Expiry date:

30/09/2030

Model:

Maximum operating temperature 50°C: JS 1,6-02 JS 1,6-04 JS 1,6-NK JS 1,6-NKP JS 4-02 JS 4-04 JS 4-NK JS 4-NKP JS 2,5-02 JS 2,5-04 JS 2,5-NK JS 2,5-NKP JS 2,5-G1-02 JS 2,5-G1-04 JS 2,5-G1-NK JS 2,5-G1-NKP Maximum operating temperature 85°C: JS90 1,6-02 JS90 1,6-04 JS90 1,6-NK JS901,6-NKP JS90 2,5-02 JS90 2,5-04 JS90 2,5-NK JS90 2,5-NKP JS90 2,5-G1-02 JS90 2,5-G1-04 JS90 2,5-G1-NK JS90 2,5-G1-NKP JS90 4-02 JS90 4-04 JS90 4-NK JS90 4-NKP

Manufacturer:

Apator Powogaz S.A.

Company Name

Apator Powogaz S.A.

Address

Jaryszki 1C, 62-023 Żerniki

Country

Poland

Phone

+48 789 454 593

View All Listings by this Company

An in-line ultra-sonic water meter with brass (WM15) or plastic (SM15) bodies. Maximum working pressure: 16 Bar. Maximum operating temperature: 50°C (WM15) or 70°C (SM15).

Section:

1505 Water Meters

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

¾” BSP (M).

Marking:

Sagemcom, CE, DN, max temperature and other technical information on meter face. Flow arrow on body

Installation Requirements:

R001

Expiry date:

30/09/2030

Model:

WM15: available in 110mm, 115mm, 165mm lengths. SM15: available in 110mm length.

Approval Holder:

Sagemcom Energy & Telecom

Company Name

Sagemcom Energy & Telecom

View All Listings by this Company

Range of water meters with plastic bodies and plastic turbines. The inlet incorporates a plastic strainer. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.

Section:

1505 Water Meters

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

SJ-SDC plus.

Marking:

NWM, NWM logo, and tech info on dial face. Flow arrow and DN on valve body. NWM & NWM logo on cover.

Installation Requirements:

R001

Expiry date:

30/09/2030

Model:

½” BSP (M) inlet / ½” BSP (M)outlet (DN15), ¾” BSP (M) inlet / ¾” BSP (M)outlet (DN20), ½” NPT (M) inlet / ½” NPT (M) outlet (DN15), ¾” NPT (M) inlet / ¾” NPT (M) outlet (DN20).

Approval Holder:

Ningbo Water Meter (Group) Co., Ltd

Company Name

Ningbo Water Meter (Group) Co., Ltd

Address

No 355 Hongxing Road Jiangbei District Ningbo

Country

China

View All Listings by this Company

Range of flow sensors incorporating either brass, plastic or stainless steel bodies & EPDM ‘O’-rings. Maximum working pressure 10.0 bar for models VVXA, VVXC, VVXB. Maximum working pressure 16.0 bar for models VVXD & VVXE. Maximum operating temperature 90°C.

Section:

1530 Miscellaneous Fittings

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See models.

Marking:

Sika logo, pressure, temperature, other tech info on body; flow arrow on body.

Installation Requirements:

R001

Expiry date:

30/09/2030

Model:

VVXA Vortex Flow Sensor Type VVX15 Vortex Flow Sensor nominal size 15. Body material PPS, G ¾ male or ½” NPT male VVXC Vortex Flow Sensor Type VVX20 Vortex Flow Sensor nominal size 20. Body material PPS G 1 male or ¾” NPT male or Quick-Fasten male/female VVXB Vortex Flow Sensor Type VVX25 Vortex Flow Sensor nominal size 25. Body material PPS G 1¼ male or 1” NPT male VVXD Vortex Flow Sensor Type VVX32 Vortex Flow Sensor nominal size 32. Body material brass or stainless steel G 1½ male or 1½” NPT male VVXE Vortex Flow Sensor Type VVX40 Vortex Flow Sensor nominal size 40. Body material brass or stainless steel G 2 male or 2” NPT male • digit 1,2,3: Designation of the series o VVX >>> VVX series • digit 4: nominal diameter o A >>> DN 15 for type VVX15 o C >>> DN 20 for type VVX20 o B >>> DN 25 for type VVX25 o D >>> DN 32 for type VVX32 o E >>> DN 40 for type VVX40 • digit 5,7,8,9,10,11,12,13,14,15: Device configuration • digit 6: Private label o S >>> SIKA (standard) o E >>> SIKA (standard) with ETL marking • digit 4 and 16: tube material / process connection o A and 4 >>> PPS – G 3/4 male thread o A and C >>> PPS – ½”NPT male thread o C and P >>> PPS – Quick-Fasten connection o C and 7 >>> PPS – G 1 male thread o C and 8 >>> PPS – 3/4" NPT male thread o B and 6 >>> PPS – G 1 1/4 male thread o B and E >>> PPS – 1” NPT male thread o D and U >>> Brass – G 1 1/2 male thread o D and 0 >>> Brass – 1½" NPT male thread o D and M >>> Stainless steel – G 1 1/2 male thread o D and Y >>> Stainless steel – 1½" NPT male thread o E and X >>> Brass – G 2 male thread o E and 9 >>> Brass – 2" NPT male thread o E and O >>> Stainless steel – G 2 male thread o E and Z >>> Stainless steel – 2" NPT male thread

Approval Holder:

SIKA Systemtechnik GmbH

Company Name

SIKA Systemtechnik GmbH

Address

Struthweg 7-9 Kaufungen

Postcode

34260

Country

Germany

Phone

+49 5605 803 652

General Email

grass@sika.net

View All Listings by this Company

Range of EPDM expansion joints with flanged end conenctors. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.

Section:

1530 Miscellaneous Fittings

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See model.

Marking:

SHANGHAI LIANYANG METAL & RUBBER CO., LTD logo (‘MR-FLEX’) and size on body.

Installation Requirements:

R001

Expiry date:

30/09/2030

Model:

S-100: DN32 - DN300, S-101: DN25 - DN300, S-115: DN25 - DN300.

Product Images

Approval Holder:

SHANGHAI LIANYANG METAL & RUBBER CO., LTD

Company Name

SHANGHAI LIANYANG METAL & RUBBER CO., LTD

Address

No.2 Building, No.399 Zhongqu Road, Industrial estate Maogang Town, Songjiang, Shanghai

Country

China

General Email

sha.lyang@kenpogroup.com

View All Listings by this Company

Manufacturer:

SHANGHAI LIANYANG METAL & RUBBER CO., LTD

Company Name

SHANGHAI LIANYANG METAL & RUBBER CO., LTD

Address

No.2 Building, No.399 Zhongqu Road, Industrial estate Maogang Town, Songjiang, Shanghai

Country

China

General Email

sha.lyang@kenpogroup.com

View All Listings by this Company

Range of electromagnetic flow meters with carbon steel bodies, NBR inner liner and stainless-steel electrodes. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.

Section:

1530 Miscellaneous Fittings

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

DN50 - DN300 flanged.

Marking:

Tianjin Sure Instrument Co., Ltd. trademark logo (‘sure’), Tianjin Sure Instrument Co., Ltd., product type, model number, series number and other technical information on data plate on body.

Installation Requirements:

R001

Expiry date:

30/09/2030

Model:

LDG-WR

Product Images

Approval Holder:

Tianjin Sure Instrument Co., Ltd.

Company Name

Tianjin Sure Instrument Co., Ltd.

Address

No.6-6, Yan'an Road, Nankai District, Tianjin

View All Listings by this Company

Manufacturer:

Tianjin Sure Instrument Co., Ltd.

Company Name

Tianjin Sure Instrument Co., Ltd.

Address

East of Huifeng Road and south of Fazhan Road, North District, Qingxian Economic and Technological Development Zone, Cangzhou City, Hebei Province

View All Listings by this Company

Range of pumps, with stainless steel bodies, impellers and shaft. Maximum working pressure 10.0 bar. Cold water use only.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

250904702

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See models.

Marking:

Wilo, made in Korea, Model No., Serial No., website address, & other tech info on data label. Wilo printed on control panel.

Installation Requirements:

R001 R415

Expiry date:

30/09/2030

Model:

PBI-L203EA - Suction 25A(1”) Discharge 25A(1”) PBI-L204EA - Suction 25A(1”) Discharge 25A(1”) PBI-L205EA - Suction 25A(1”) Discharge 25A(1”) PBI-L402EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-L403EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-L404EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-L405EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-L802EA - Suction 40A(1 1/2”) Discharge 32A(1 1/4”) PBI-L803EA - Suction 40A(1 1/2”) Discharge 32A(1 1/4”) PBI-LD203EA - Suction 25A(1”) Discharge 25A(1”) PBI-LD402EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-LD403EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-LD404EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-LD405EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-LD802EA - Suction 40A(1 1/2”) Discharge 32A(1 1/4”) PBI-LD803EA - Suction 40A(1 1/2”) Discharge 32A(1 1/4”) 1 - Series PBI-L: Electronic Boosting Pump Variable Speed Pump(Inverter Pump). 2 - Number of Pumps None/blank : Single Type (One Pump), D: Duplex Type (Two Pumps). 3 - Rated Flow capacity 2 : 2㎥/hr, 4 : 4㎥/hr, 8 : 8㎥/hr. 4 - Number of Impellers 02 : 2 Impellers, 03 : 3 Impellers, 04 : 4 Impellers, 05 : 5 Impellers. 5 - Power 60Hz L: 110V ~, J: 120V ~ , 127V~, M: 220V~ D: 110V/220V~, I: 220/380V 3~, T: 220V 3~, U: 380V 3~, N: 440V 3~, R: 480V 3~. 50Hz Z: 110V ~, C: 120V ~, 127V~, E: 220V ~, F: 110V/220V ~, G: 220/380V 3~, H: 220V 3~, Q: 380V 3~, Y: 440V 3~. 6 - Automatic mode. None/blank : non automatic models A: models which equips themselves with components that are responsible for automatic mode.

Approval Holder:

WILO Pumps Ltd.

Company Name

WILO Pumps Ltd.

Address

View All Listings by this Company

Range of wall mounted angled overhead showers, consisting of stainless-steel bodies (various finishes) and silicone nozzles. The inlets are fitted with plastic flow limiters. Maximum operating temperature 65⁰C. Open outlet use only.

Section:

1650 Shower Outlets

Section Subtitle:

Shower head(s) and/or shower handset(s).

WRAS Approval Number:

250908001

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Note:

Flow rates declared by manufacturer are not endorsed by WRAS.

Size:

½” BSP (M).

Marking:

Manufacturers logo on the underside of body.

Installation Requirements:

R001 R040

Expiry date:

30/09/2030

Model:

DB3000.a.bbb Where ‘a’ in the above code it will be as a number 1 – 9 to denote the finish i.e.DB3000.1 is a brushed finish, DB3000.2 is a mirror polished finish, ceramic coated etc. Where ‘bbb’ in the above code will be a number 00-999, either 2 or 3 digits to denote the colour of the finish where applicable i.e. DB3000.3.50 is a brushed finish with a gold PVD coating DB3000.6.03 is a black ceramic coating.

Approval Holder:

Dolphin Solutions Limited

Company Name

Dolphin Solutions Limited

Address

Southpoint Compass Park Bodiam East Sussex

Postcode

TN32 5BS

Country

United Kingdom

General Email

Ralph.Mumford@dolphinsolutions.com

View All Listings by this Company

Range of brass shower arms and plastic shower heads (various finishes) incorporating EPDM seals and ‘O’-rings, silicone seals and spray insert. The 26 469 xxx model is ceiling mounted & 26 470 xxx model is wall mounted. Maximum operating temperature 60°C. Open outlet use only.

Section:

1650 Shower Outlets

Section Subtitle:

Shower head(s) and/or shower handset(s).

WRAS Approval Number:

250808004

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

½” BSP (F).

Marking:

Hansgrohe on the body.

Installation Requirements:

R001 R040

Expiry date:

31/08/2030

Model:

26 469 xx0 Hansgrohe Raindance select S – Overhead shower 240 2 jet EcoSmart with ceiling connector. 26 470 xx0 Hansgrohe Raindance select S – Overhead shower 240 2 jet EcoSmart with shower arm. 26 469 400 Hansgrohe Raindance select S – Overhead shower 240 2 jet EcoSmart with shower arm.

Approval Holder:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Auestrasse 5 - 9, Schiltach

Postcode

77761

Country

Germany

Phone

+49 170 4471 718

General Email

Ludovic.hauer@hansgrohe.com

View All Listings by this Company

Range of wall or ceiling mounted shower arms with stainless steel bodies (various finishes - see model). Maximum operating temperature 60°C.

Section:

1650 Shower Outlets

Section Subtitle:

Shower head(s) and/or shower handset(s).

WRAS Approval Number:

250912013

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Note:

Open outlet use only.

Size:

½” BSP (M).

Marking:

SUERDA on back plate.

Installation Requirements:

R001 R040

Expiry date:

30/09/2030

Model:

Round Wall Arm: SD7033-22 - Chrome, SD7033-22BK - Black, SD7033-22BB - Brushed Brass. Square Wall Arm: SD7033-23 - Chrome, SD7033-23BK - Black, SD7033-23BB - Brushed Brass. Round Ceiling Arm: SD7033-24 - Chrome, SD7033-24BK - Black, SD7033-24BB - Brushed Brass. Square Ceiling Arm: SD7033-25 - Chrome, SD7033-25BK - Black, SD7033-25BB - Brushed Brass.

Product Images

Approval Holder:

ZHEJIANG SUERDA SANITARY CO.,LTD.

Company Name

ZHEJIANG SUERDA SANITARY CO.,LTD.

Address

No.39 Changshun Road, Bingang Industrial Zone, Shamen Town, Yuhuan County, Zhejiang

Country

China

View All Listings by this Company

Manufacturer:

ZHEJIANG SUERDA SANITARY CO.,LTD.

Company Name

ZHEJIANG SUERDA SANITARY CO.,LTD.

Address

No.39 Changshun Road, Bingang Industrial Zone, Shamen Town, Yuhuan County, Zhejiang

Country

China

View All Listings by this Company

Range of overhead shower outlets. The inlet incorporates a stainless-steel filter washer. Maximum operating temperature 65°C.

Section:

1650 Shower Outlets

Section Subtitle:

Shower head(s) and/or shower handset(s).

WRAS Approval Number:

250912015

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Note:

Open outlet use only.

Size:

½” BSP (F).

Marking:

SUERDA on body.

Installation Requirements:

R001 R040

Expiry date:

30/09/2030

Model:

Round Slim Shower Head: SD42508 - 300mm - Chrome. Square Slim Shower Head: SD42509 - 300mm - Chrome. Square Shower Head: SDH1D121 - 250mm - Chrome, SDH1D121BK - 250mm - Black, SDH1D121BB - 250mm - Brushed Brass. Round Shower Head: TS03301 - 250mm - Chrome, TS03301BK - 250mm - Black, TS03301BB - 250mm - Brushed.

Product Images

Approval Holder:

ZHEJIANG SUERDA SANITARY CO.,LTD.

Company Name

ZHEJIANG SUERDA SANITARY CO.,LTD.

Address

No.39 Changshun Road, Bingang Industrial Zone, Shamen Town, Yuhuan County, Zhejiang

Country

China

View All Listings by this Company

Manufacturer:

ZHEJIANG SUERDA SANITARY CO.,LTD.

Company Name

ZHEJIANG SUERDA SANITARY CO.,LTD.

Address

No.39 Changshun Road, Bingang Industrial Zone, Shamen Town, Yuhuan County, Zhejiang

Country

China

View All Listings by this Company

Range of PVC lined flexible shower hoses with a black or silver finish. Open outlet use only. Maximum operating temperature 60°C.

Section:

1650 Shower Outlets

Section Subtitle:

Shower head(s) and/or shower handset(s).

WRAS Approval Number:

2109386

Size:

½” BSP captive and conical nut

Marking:

Ideal standard logo on conical nut.

Installation Requirements:

R001

Expiry date:

30/09/2026

Model:

BE192AA, Bright Silver 1.25M BE193AA, Bright Silver 1.75M BE192XG, Black 1.25M BE193XG, Black 1.75M

Product Images

Approval Holder:

Ideal Standard (UK) Ltd

Company Name

Ideal Standard (UK) Ltd

Address

Old Road (Lodge 1) Armitage, Rugeley, Staffordshire

Postcode

WS15 4BT

Country

United Kingdom

General Email

tyeomans@idealstandard.co.uk

View All Listings by this Company

Range of flanged `Y` patterned in-line strainers with blue, black or red epoxy coated ductile iron bodies, stainless steel mesh. Maximum working pressure 16 Bar. Maximum operating temperature 85°C.

Section:

1715 Strainers

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

DN40 – DN600

Marking:

JD logo and product info on data plate. Size, pressure & flow arrow on body.

Installation Requirements:

R001

Expiry date:

31/10/2029

Model:

V4

Product Images

Approval Holder:

JD Fire Ltd.

Company Name

JD Fire Ltd.

Address

Wheatfield Works, Ashton Road, Oldham

Country

OL8 3HX

View All Listings by this Company

Section:

1800 Taps

Description:

A Range of Pillar tap(s).

Deck mounted Capable of achieving AUK3 Tap Gap

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R006

Expiry date:

30/09/2030

Product Images

Approval Holder:

Guangzhou IAPMO Laboratory Co. Ltd

Company Name

Guangzhou IAPMO Laboratory Co. Ltd

Address

No.201, Building A, Yushu Industrial Park Science City Huangpu District Guangzhou

Country

China

General Email

Qiunan.Liang@iapmortl.org

View All Listings by this Company

Manufacturers:

Taizhou Xinya Sanitary Ware Co., Ltd

Pillar taps (chromium plated brass) with quarter turn ceramic disc headworks and cross top operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with plastic back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.

Section:

1800 Taps

Section Subtitle:

Pillar tap(s).

WRAS Approval Number:

250912018

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

¾” BSP (M).

Marking:

SUERDA on body.

Installation Requirements:

R001 R005

Expiry date:

30/09/2030

Model:

SH2A513 - Bramley Bath Taps Pair Chrome.

Product Images

Approval Holder:

ZHEJIANG SUERDA SANITARY CO.,LTD.

Company Name

ZHEJIANG SUERDA SANITARY CO.,LTD.

Address

No.39 Changshun Road, Bingang Industrial Zone, Shamen Town, Yuhuan County, Zhejiang

Country

China

View All Listings by this Company

Manufacturer:

ZHEJIANG SUERDA SANITARY CO.,LTD.

Company Name

ZHEJIANG SUERDA SANITARY CO.,LTD.

Address

No.39 Changshun Road, Bingang Industrial Zone, Shamen Town, Yuhuan County, Zhejiang

Country

China

View All Listings by this Company

Pillar taps (chromium plated brass) with quarter turn ceramic disc headworks and cross top operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with plastic back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.

Section:

1800 Taps

Section Subtitle:

Pillar tap(s).

WRAS Approval Number:

250912019

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

½” BSP (M).

Marking:

SUERDA on body.

Installation Requirements:

R001 R006

Expiry date:

30/09/2030

Model:

SH2A513-2 - Bramley Basin Taps Pair Chrome

Product Images

Approval Holder:

ZHEJIANG SUERDA SANITARY CO.,LTD.

Company Name

ZHEJIANG SUERDA SANITARY CO.,LTD.

Address

No.39 Changshun Road, Bingang Industrial Zone, Shamen Town, Yuhuan County, Zhejiang

Country

China

View All Listings by this Company

Manufacturer:

ZHEJIANG SUERDA SANITARY CO.,LTD.

Company Name

ZHEJIANG SUERDA SANITARY CO.,LTD.

Address

No.39 Changshun Road, Bingang Industrial Zone, Shamen Town, Yuhuan County, Zhejiang

Country

China

View All Listings by this Company