Range of spherical valves (nickel plated) brass bodies with single lever operating members, (chromium plated) brass ball and PTFE seat. Maximum working pressure 40.0 bar (Models 124-1027 CST, 124-1028 CST and 124-1029 CST) Maximum working pressure 25.0 bar (Models 124-1030 CST and 124-1031 CST) Maximum working pressure 16.0 bar (Models 124-1032 CST and 124-1033 CST) Maximum operating temperature 85°C.
Range of angled isolation ball valves incorporating brushed chrome plated DZR brass bodies, DZR brass ball (chrome plated), stainless steel strainer and approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of double regulating valves incorporating bronze bodies, brass disc face (½” - ¾” models) or PTFE (1” - 2” models), PTFE plate and NBR ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of commercial front loading, hood type & utensil washer type dishwashing machines with flow controlled by solenoid and discharged via type AB air gap (verified by test - suitable for backflow protection against fluid category 5) . The products are supplied with a grey coloured PVC supply hose. Maximum working pressure 6.0 bar. Maximum operating temperature 90°C.
Range of electrolytic scale inhibitors incorporating copper bodies. For use with copper pipe complying with BS EN 1057. Maximum working pressure 10.0 bar. Maximum operating temperature 40°C.
Range of UV disinfection units with stainless steel and EPDM seals. The UV lamps are housed inside synthetic quartz tubes Maximum working pressure 6.9 bar. Cold water use only.
Silver and copper disinfection ion generator with a plastic body, incorporating a plastic flow switch. Maximum working pressure 9.0 bar. For cold water use only
'Droople DRP-M90-IMP'. White coloured, injection moulded acetal cogwheel. For use with water up to 65°C.
Injection moulded POM materials. 'POMM90-BK02' is black coloured and for use with water up to 60°C. ‘POMM90-GR05 & POMM90-GR37’ are grey coloured and were added to the approval in November 2022, they are for use with water up to 85°C.
'SYAL B950' (brown coloured) & 'SYAL A950' (white coloured). Dry press moulded ceramic materials. For use with water up to 85°C.
'Korepox H.B EH3100'. Factory applied, two component, cream coloured epoxy resin coating. Mix in a 3:1 volume ratio and apply as per manufacturer's instructions dated April 2009. Cure for 7 days@25°C. For use with water up to 40°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'EPOKIM Painting System'. Factory applied, dark green coloured (once top coat applied), two-component epoxy coating comprising of a primer and top coat. The primer (EPOX code A0768.N05133 + cat.A0918.N00100) consists of a catalyst and hardener which should be mixed in a 100:43 volume ratio before applying two coats in accordance with instructions ‘W1_2021_00’ dated ‘25/10/2021’. Cure (flash-off) for 40 minutes@40°C. The top coat (EPOKIM HS code A0435.N02038 + cat.A0904.N00000) consists of a catalyst and hardener which should be mixed in a 100:16 volume ratio before applying one coat in accordance with instructions ‘W1_2021_00’ dated ‘25/10/2021’. Cure (flash-off) for 10 minutes@20°C. The complete system should then be ‘stoved’ for 60 minutes@70°C. For use with water up to 23°C.
'DUAYEN E-39'. Factory applied, two-component, red coloured (once mixed) epoxy coating. Mix Parts A&B in a volume ratio of 79.5:20.5 and apply as per manufacturer's instructions '00.05102021'. Cure for 7 days@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'ENDOPRENE®84-30 THIXO'. Factory applied, cream coloured two-part polyurethane coating consisting of a resin and hardener. Mix and apply as per manufacturer`s technical data sheet (version dated 16/12/2019). Cure for 48 hours at 20°C. For use with water up to 55°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ENDOPRENE® 891.20 RACCORD'. Factory applied, cream coloured two-part polyurethane coating consisting of a resin and hardener. Mix and apply as per manufacturer`s technical data sheet 'Doc. 087' (version dated 01/07/2011). Cure for 48 hours at 20°C. For use with water up to 55°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Cepox P05/95'. Factory applied, two part, yellow coloured epoxy coating. Mix and apply as per Technical Data Sheet dated 19/11/2021. Cure for 16 hours@70°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'DAT-01'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a weight ratio of 34.4:44.9:20.7. Cure for 8 hours@50°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MS519'. Factory applied, blue coloured Porcelain Enamel coating. Apply as per manufacturer's instructions dated 2021.6.23. Dry for 2 hours@100°C before firing for 10 minutes@860°C For use with water up to 75°C. This material is only approved for the drying and firing conditions that appear on the approval. If the drying and/or firing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`Belzona 1321`. Site applied, two-part, epoxy amine coating available in grey or blue colours. Mix base and hardener in a 11:1 mass ratio. Apply and cure as per manufacturer’s IFU ‘FN10026’, publication number ’02-09-21’. For use with water up to 23°C. These materials are only approved for the mixing conditions that appear on the approval. If the mixing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Orgal® Hydroflex 10'. White coloured, acrylic polymer emulsion cement modifier, which is a liquid additive intended to be mixed with cement to achieve a coating. Mix cement:additive:water in a 197.5:30:10 mass ratio and apply as per manufacturer's instructions '2/18'. Cure for 28 days@23°C and @50% relative humidity. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
Page 42 of 204
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
