Range of threaded fittings with either brass or chrome plated brass bodies. Maximum working pressure 40 Bar Maximum operating temperature 85°C.
CM(E) range of electronically operated pumps available in stainless steel, (‘EN 1.4301/AISI304’ or ‘EN 1.4401 /AISI316’) and cast iron. The pumps are supplied with Sic-Sic mechanical shaft seals and FKM or EPDM seals. Maximum operating parameters: Cast iron models: Maximum working pressure 6.0 bar @ 90°C. Maximum working pressure 10.0 bar @ 40°C. Stainless steel models (not self-priming variants): Maximum working pressure 10.0 bar @ 99°C. Maximum working pressure 16.0 bar @ 90°C. Stainless steel self-priming models (CM(E) 1, 3 & 5 (AISI 304) only): Maximum working pressure 10.0 or 16.0 bar @ 60°C.
Range of stainless-steel braided EPDM lined flexible hose assemblies with a variety of end connections. Some models incorporate push-fit isolation valves. Compression connection to be used with DM LLDPE pipes or PEX barrier pipe manufactured to BS7291-3. Maximum working pressure and maximum operating temperature 12 bar @cold water use only & 7 bar @ 65°C.
Air source heat pump with a temperature and pressure relief valve (7.0 Bar) factory fitted. Maximum working pressure 5.5 bar. Maximum operating temperature 70°C.
Range of domestic stainless steel or coated carbon steel indirect unvented hot water storage cylinders and buffer tanks, incorporating a stainless-steel coil for connection to a heat pump circuit. The secondary circuit is factory fitted with a temperature and pressure relief valve (7.0 Bar) and an immersion heater. Maximum working pressure 5.5 bar except for model EG-200CAIO 8.0bar. Maximum operating temperature 70°C. Model ECO-ZR60S is used in primary circuit only.
Wall mounted, bar type thermostatic blending valves (chromium plated brass) incorporating a quarter turn ceramic disc headwork, controlling and diverting the flow between overhead shower and handset, with dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member which incorporates a manual override button. Both inlets incorporate stainless steel strainer and approved check valve cartridges, however, the complete products have not been fully tested to demonstrate that they provide backflow protection Maximum working pressure 10.0 bar. Non-metallic materials and components comply with BS6920 at 85°C
Non-metallic materials and components comply with BS6920 at 85°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| AQ75BAR1 | Chrome | 15mm compression | 10 bar | 65 °C | AQUALISA | Valve body | No | Non-rising spindle | Not Applicable | Shower Hose, Handset, | |
| TS75BAR1 | Chrome | 15mm compression | 10 bar | 65 °C | AQUALISA | Valve body | No | Non-rising spindle | Not Applicable | Shower Hose, Handset, |
AQ75BAR1 Packed Products. Waterway contents are: • 704308 (shower valve) • 704418 (shower handset) • ACY1008 (shower hose) TS75BAR1 Packed Products. Waterway contents are: • 704308 (shower valve) • 707540 (shower handset) • ACY1008 (shower hose)
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| AQRNDCV1 | Chrome | 5 bar | 65 °C | Aqualisa | shower valve | No | Ceramic cartridge | Not Applicable | Not Applicable | Shower Hose, Handset, |
AQRNDCV1 Packed Products. Waterway contents are: 705342 (shower valve) 704418 (shower handset) ACY1008 (shower hose) ACY1013 (wall outlet)
Range of lugged butterfly valves incorporating black epoxy coated ductile iron bodies, EPDM seats and stainless-steel discs. The products are operated by: DN50~DN200: Lever or DRV lever operating members. DN50~DN600: Gearbox or DRV gearbox operating members, or bare shaft without operating members. Maximum working pressures: RBV020-H models: 16.0 bar, RBV-S/PN25 models: 25.0 bar Maximum operating temperature 85°C.
Range of butterfly valves with blue epoxy coated ductile iron bodies, stainless-steel discs and EPDM or PTFE seats (see models). Maximum working pressure 16.0 Bar or10.0 Bar (see models). Maximum operating temperature 85°C.
Range of 2-way ceramic disc diverters/headworks (2 on, 1 off) with a plastic body to be housed in specifically dimensioned bodies. Maximum working pressure 12.0 bar. Maximum operating temperature 85°C.
Range of brass bodied concealed flow control vales with trim sets in various finishes (see model), incorporating a quarter turn ceramic disc headwork with various operating members. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
‘GNVP’ range of non-return valves with a white plastic housing. The product incorporates two test/drainage plugs. Maximum working pressure 16.0 bar. Maximum operating temperature 60°C.
Range of pressure reducing valves, manually adjustable outlet pressure from 0.5 bar - 6.5 bar, with DZR brass bodies and inspection ports on both the inlets and outlets. The valves incorporate plastic strainers. Maximum working pressure 25 bar. Maximum operating temperature 85˚C.
Solenoid valve with a brass body, EPDM diaphragm and ‘O’-rings. Maximum operating pressure 10.0 bar. Cold water use only.
Range of spherical valves with various means of operation some via handle some with actuators, see models, comprising of a bronze valve body, spindle and ball valve, and EPDM O rings Maximum working pressure 16 bar Maximum operating temperature 90˚C.
Range of angled (S0273 and S0274 suffix models only) or in-line spherical valves with a nickel plated brass body, chromium plated brass ball and PTFE or EPDM seats. The products are either screwdriver operated or supplied with a T-handle (S0233BH-1 and S0233BH-2 models only). Compression ends are for use with copper pipes (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of screwdriver operated spherical valves incorporating brass bodies, brass balls (chrome plated) and EPDM ‘O’-rings. For use with copper pipe to (EN1057). Maximum working pressure 16 Bar Maximum operating temperature 85°C.
Spherical valves with chrome or nickel plated brass body, chrome plated ball, PTFE seats and FKM ‘O’-ring. The products are available with lever, lockable lever or tee handles. Maximum working pressure 40.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated ductile iron bodies, EPDM coated ductile iron wedge and EPDM seals. Valves are operated via a non-rising spindle headwork. With lever or gear operating member. Maximum working pressure 16.0 Bar Maximum operating temperature 100.0°C
Page 393 of 394
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
