Range of Electromagnetic water conditioners. Maximum working pressure 16.0 bar. Cold water use only.
Range of UV disinfection units with stainless steel bodies. Maximum working pressure 10.0 bar. Cold water use only.
Range of UV disinfection units with stainless steel bodies and quartz tube. Maximum working pressure 10.0 bar. Cold water use only.
Range of UV disinfection units with stainless steel bodies. Maximum working pressure 10.0 bar. Cold water use only.
'ANUBIT HB-1000'. Factory applied, black coloured bitumen coating. Apply as per manufacturer's TDS 'AE-TDS-023-2021', dated '02.08.2024'. Please note that use of a thinner isn't covered by the scope of this approval. Cure for 40 minutes@30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Tuffkote Bituminous Aluminium'. Factory applied, grey coloured, two-component crude oil bitumen coating. Mix in a 17.1:2.9 volume ratio and apply as per manufacturer's data sheet 'SPL/PMG/2019100166', 'Rev 2', dated '04/2024'. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'HT 204'. Grey coloured carbon bearing, pressed, sintered, impregnated with phenolic resin and rebaked. For use with water up to 85°C.
'P.HSR 42.5-010Y'. Factory applied, grey coloured, Sulphate resistant Portland cement. Mix cement, sand and water in a 1:1.5:0.5 mass ratio and apply as per manufacturer's usage instructions 'JXT/JS02-10', edition '1/0', dated '2021-11-30'. Cure for 240 minutes@25°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotapipe AC - 1003 Blue and Jotapipe AC - 1003 Green'. Factory applied, blue or green coloured fusion bonded epoxy coatings (manufactured in Dubai, U.A.E). Apply as per manufacturer's Technical Data Sheet dated 26th September 2019. Cure for 2 minutes@245°C. The blue coating is for use with water up to 85°C. The green coating is for use with water up to 23°C. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'P.HSR 42.5-XP2501'. Factory applied, grey coloured, Sulphate resistant Portland cement. Mix cement, sand and water in a 1:1.5:0.5 mass ratio and apply as per manufacturer's usage instructions 'XP2503-010', dated '2025-03-25'. Cure for 240 minutes@25°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'P.HSR 42.5-RVK2025'. Factory applied, grey coloured, Sulphate resistant Portland cement. Mix cement, sand and water in a 1:1.5:0.5 mass ratio and apply as per manufacturer's usage instructions 'RVK2503/25', dated 'March 25, 2025'. Cure for 240 minutes@25°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Guom-07'. Factory applied, grey coloured cement mortar. Mix sand, cement and water in a weight ratio of 1:1.5:0.6 and apply as per manufacturer's User Instructions 'GUOM-24', 'Vision: B', dated '2024-11-5'. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MAVM554'. Factory applied, blue coloured, epoxy powder coating. Apply as per manufacturer's data sheet 'FR.07.03.18', dated 09.19. Cure for 10 minutes at 160°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Solvent Free Epoxy Coating XH4205'. Factory applied, white coloured, two-component epoxy coating. Mix Coat 1 (XH4205/grey coating & XH7322) in a 5:1 weight ratio and apply as per ‘Application Procedure 2024IV, v1', issue date '2025/01/01'. Cure for 24 hours@25°C. Mix Coat 2 (XH4205/white coating & XH7322) in a 5:1 weight ratio and apply as per ‘Application Procedure 2024IV, v1', issue date '2025/01/01'. Cure for 7 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotapipe AC - 1003 Blue & Green. Factory applied, green or blue coloured epoxy coatings (manufactured in Dammam, Saudi Arabia). Apply as per manufacturer's MTI '001 - 2024 - SA – EN'. Cure for 4 minutes@230°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Electroline ES 424'. Factory applied, white coloured, two-component epoxy coating. Mix Part A and Part B in a volume ratio of 2:1 and apply as per manufacturer's TDS 'ECL/ TDS / ES424', version '0', dated '05.01.2024'. Cure for 7 days@30°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Eco Coat Epoxy Blue Patch Up Paint (PFC/1017)'. Factory applied, blue coloured, two-component epoxy coating. Mix in a 3:2 volume ratio and apply as per manufacturer's IFU 'DOC/PFC/PU/101', dated '01.04.2024'. Cure for 8 hours@30°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`MECH WEY-Black, WEY-Red & WEY-Blue`. Factory applied epoxy coatings. Apply and cure as per manufacturer's instructions '24136' dated 2025/1/26. For use with water up to 85°C.
'EM6/35/7541/1'. Factory applied, dark blue coloured Porcelain (vitreous) enamel coating. Apply as per manufacturer's instructions 'IS_003', 'rev. 01'. Cure for 16 min 875°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ET-52184 & ET-52185'. Factory applied, black coloured water-based silicone coating comprising of an under-coat (ET-52184) and finishing coat (ET-52185). Apply as per manufacturer's instructions 'V8.2' issued January 2019. Cure both undercoat and finishing coat for 10 minutes@25°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 271 of 310
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
