Range of compression fittings with brass bodies for use with copper pipe (EN1057). Above ground use only. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
Range of “Effast” ABS fittings for use with ABS pipe complying with BS EN 5391-2006. Maximum working pressure: 15 Bar. Maximum operating temperature: 23°C.
Range of end feed copper fittings for use with copper tube to EN 1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of end feed copper solder fittings for use with copper tube. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of stainless-steel plate heat exchanger assemblies incorporating single or twin pumps on the primary circuit. Maximum working pressure 10 Bar (UKE-8 models) or 6 bar (UKE-14 models).
Non-metallic materials and components comply with BS6920 at 85°C
Range of commercial air or liquid cooled ice making machines with water controlled via solenoid valve. Maximum working pressure 5.5 Bar COLD WATER USE
Water meter housing with DZR brass body, NBR ‘O’-rings and incorporates a spherical valve. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 80°C
Talbot Modular Manifold System with and without concentric water meter connections with plastic bodies incorporating screw down stopvalves. Maximum working pressure 16 bar. Cold water use only.
Range of pressure transmitters with stainless steel bodies and an EPDM ‘O’-ring. Maximum working pressures 50.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of pull-out spray assemblies with a flexible hose and a self-closing trigger. Maximum working pressure 10.0 bar. Cold water use only.
Range of circulator pumps with brass bodies, plastic impellor, and EPDM ‘O’-rings and seals. The COMFORT 15-14 BX prefix models incorporate a screwdriver operated isolation valve on the inlet and a non-return valve at the outlet. These are housed within 1” BSP (M) x ½” BSP (M) adaptors. Maximum working pressure 10.0 Bar. Maximum operating temperature 95°C.
Range of shower heads with brass bodies (various finishes) incorporating EPDM washers with built in strainers. Some models also incorporate flow regulators.
Non-metallic materials and components comply with BS6920 at 85°C
Range of ceiling or wall mounted shower outlets, (brass or stainless-steel bodies - various finishes) incorporating EPDM `O` rings. Maximum operating temperature 60.0°C
A range of ceiling mounted and wall mounted shower outlets (brass and stainless-steel bodies - various finishes) incorporating EPDM O-rings.
Non-metallic materials and components comply with BS6920 at 60°C
Range of shower handsets and an overhead shower outlet with plastic bodies (chrome plated, chrome plated/white or chrome plated/black coloured finish - see model). The inlet of the 2.1981.018 model incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection.
Non-metallic materials and components comply with BS6920 at 55°C
Range of shower outlets (brass or stainless-steel bodies – various finishes) incorporating EPDM O-rings. Maximum operating temperature 60.0°C
Non-metallic materials and components comply with BS6920 at 60°C
Wall mounted shower outlet (brass body – various finishes). The product is supplied with shower hose and handset that incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection.
Non-metallic materials and components comply with BS6920 at 60°C
Range of overhead showers consisting of stainless steel bodies and silicone nozzles and gaskets and shower handsets consisting of ABS (LB-2003N, LB-2003, LB-2004) or brass bodies (LB-2006 & LB-2028).
Non-metallic materials and components comply with BS6920 at 60°C
Range of shower outlets with brass bodies (various finishes) and NBR ‘O’-rings. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of draining taps with DZR brass, brass or chrome plated brass bodies. Incorporating a rising spindle headwork, EPDM or NBR seals and washers. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Page 27 of 63
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
