'SPL Gold Portland Slag Cement'. Grey coloured, factory applied Portland Slag cement. Mix cement, sand & water in a 1:1.4:0.35 mass ratio. Apply as per manufacturer's work instructions document code 'WI/SP/FINC&B/02', issue '06'. Cure for 24 hours@27°C, 70% relative humidity. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Pipeclad 704G'. Factory applied, green coloured epoxy coating. Apply as per manufacturer's product information dated 'August 16,2022'. Cure for 12 minutes@232°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘ET Ordinary Portland Cement’. Factory applied, grey coloured cement. Mix and apply as per manufacturer’s ‘Standard Operating Procedure 'ET-SAM/DIP-PP/SOP/013', 'Rev. No 01', dated '15.12.2019'. Cure for 40 days@26°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘ET Sulphate Resisting Cement’. Factory applied, grey coloured cement. Mix and apply as per manufacturer’s ‘Standard Operating Procedure 'ET-SAM/DIP-PP/SOP/014', 'Rev. No 01', dated '15.12.2019'. Cure for 40 days@26°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘ET Blast Furnace Slag Cement’. Factory applied, grey coloured cement. Mix and apply as per manufacturer’s ‘Standard Operating Procedure 'ET-SAM/DIP-PP/SOP/012', 'Rev. No 01', dated '15.12.2019'. Cure for 40 days@26°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'RMD 7080/xx, RUD 2230/xx, RMD 7100/xx, RUD 2247/xx, RUD 2273/xx, RMD 7061/xx'. 'xx' denotes the customer and can be replaced with numbers between 01 & 99. Factory applied, blue coloured enamel coating. Apply as per manufacturer's instructions '0703231010' dated 14.03.23. Cure for 10 minutes@860°C. For use with water up to 85°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Lionpak 2500'. Yellow & black striped, braided gland packing. For use with water up to 85°C. For use as a gland packing only having been tested at a reduced surface area to volume ratio.
'Lionpak 2100'. White coloured, braided, PTFE gland packing. For use with water up to 85°C. For use as a gland packing only having been tested at a reduced surface area to volume ratio.
'DPFC GRP Pipe'. Beige/straw coloured GRP pipe manufactured by filament winding. For use with water up to 50°C.
‘PureOne hose’ (formerly known as ‘Clearwater hose’). Multi-layered hose manufactured on a mandrill by hand, consisting of a colourless, transparent PE inner layer and a blue coloured EPDM outer layer. Please note that the hose has many layers but the approval describes only the inner and outer layers. For use with water up to 50°C.
'ILPEA 70-90 EPDM HOSE WRAS AF'. Black coloured, extruded EPDM hose. Shore hardness 80. Tested in-radius size 1.3mm. For use with water up to 23°C.
'SYL-8668'. White coloured (opaque) grease. For use with water up to 70°C.
'G. BESLUX BESSIL 6001'. White coloured, opaque silicone grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
'CELANYL A3 WR GF30 NC 1102/Z/FA'. Natural (appears cream in colour), injection moulded polyamide material manufactured in Celanese(Suzhou) Engineering Plastics Co. LTD (China), & Celanese Production Germany GmbH &Co (Utzenfeld –Germany. For use with water up to 85°C.
'LHS001P'. Off-white (translucent), extruded PEX hose. For use with water up to 60°C.
'SCGC HDPE H1000PCH Pipe'. Black coloured, extruded HDPE pipe. For use with water up to 85°C.
'Taldeen Electrofusion Fitting'. Black coloured, injection moulded, PE100 Electrofusion Fitting. For use with water up to 85°C.
'Taldeen PE100 Pipe'. Black coloured (with blue external stripe), extruded, PE100 Pipe. For use with water up to 85°C.
'Jain HDPE (PE 100) Blue Fittings). Blue coloured HDPE fittings manufactured by injection moulding or extrusion. For use with water up to 65°C.
'Rainson HDPE (PE100)'. Black coloured, injection moulded HDPE (PE100) material. For use with water up to 23°C.
Page 239 of 584
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
