Range of pressure reducing valves with DZR brass bodies (CW602N or CW511L), EPDM ‘O’-rings and a stainless steel strainer. Available with a variety of end connections (see model). Models with compression, pressfit and pushfit connections are for use with copper pipe. Maximum inlet supply pressure 16.0 bar. Maximum outlet pressure between 1.5 bar and 6.0 bar. Maximum operating temperature 80°C.
Range of adjustable, in-line pressure reducing valves with blue epoxy coated, cast iron bodies. 447 70 models: maximum supply pressure 25.0 bar, outlet pressure range 1.5 to 7.0 bar. Maximum operating temperature 60°C.
Range of spherical valves with either DZR brass Nickel-plated brass or chromium plated brass bodies, nickel plated brass ball and PTFE seats. With either lever or butterfly operating members. Some models incorporate a stainless-steel filter. Compression models for use with copper pipe manufactured to EN 1057. Maximum working pressure: 10 Bar. Maximum operating temperature: 85°C.
Range of spherical valves with (bronze or brass bodies) incorporating a brass or stainless-steel ball with PTFE seat. The MV10-11240 range - Maximum operating pressure - 40 bar. Maximum operating temperature 85°C. The MV10-11202 range - Maximum operating pressure - 25 bar. Maximum operating temperature - 85°C.
Range of spherical valves with bronze bodies incorporating a brass or stainless-steel ball with PTFE seat. The ART 340 range - Maximum operating pressure - 40 bar. Maximum operating temperature 85°C.
Range of spherical valves with (bronze or brass bodies) incorporating a brass or stainless-steel ball with PTFE seat. The VAB501 range - Maximum operating pressure - 40 bar. Maximum operating temperature 85°C.
Range of straight, angled, tee and Y shaped isolation valves incorporating brass bodies, NBR ‘O’-rings or PTFE seats depending on model variant. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with (bronze or brass bodies) incorporating a brass or stainless-steel ball with PTFE seat. The BVBZ range - Maximum operating pressure - 40 bar. Maximum operating temperature 85°C. The BVBR range - Maximum operating pressure - 25 bar. Maximum operating temperature - 85°C.
Range of in-line full bore spherical valves with nickel plated brass bodies, chrome plated brass ball and either lever or ‘T’ handles (see model). The products are for use with copper pipe (manufactured to BS EN 1057). Maximum working pressures: 30.0 bar (15mm-28mm) or 25.0 bar (35mm-54mm). Maximum operating temperature 99°C.
Range of spherical valves with brass or DZR brass bodies, chromium plated brass or chromium plated DZR brass (12-18mm) or stainless-steel balls (22-54mm) and various operating members The press-fit connection is for use with copper pipes (manufactured to EN 1057), stainless steel pipes (manufactured to EN10312) or carbon steel pipes (manufactured to EN10305-3). Jointing is achieved via a crimping tool using a ‘M’ profile. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with brass or DZR brass bodies, chromium plated brass or chromium plated DZR brass (12-18mm) or stainless-steel balls (22-54mm) and various operating members The press-fit connection is for use with copper pipes (manufactured to EN 1057), stainless steel pipes (manufactured to EN10312) or carbon steel pipes (manufactured to EN10305-3). Jointing is achieved via a crimping tool using a ‘M’ profile. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with brass or chromium plated brass and various operating members The press-fit connection is for use with copper pipes (manufactured to EN 1057), stainless steel pipes (manufactured to EN10312) or carbon steel pipes (manufactured to EN10305-3). Jointing is achieved via a crimping tool using a ‘M’ profile. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of spherical ball valves with black plastic bodies, PTFE seats and EPDM ‘O’-rings. Maximum working pressure: 16 Bar. Cold Water use only.
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valve with ductile iron bodies, wedge and bonnet (blue epoxy powder coated). Valves are operated via a non-rising spindle headwork. Maximum working pressure 16.0 Bar Maximum operating temperature 99.0°C
Range of non-rising spindle gate valves with DZR brass bodies. Operating members are either handwheel operated or lockshield. Maximum working pressure: 20.0 bar. Maximum operating temperature: 100°C.
Range of non-rising spindle gate valves with DZR brass bodies. Operating members are either handwheel operated or lockshield. Maximum working pressure: 20.0 bar. Maximum operating temperature: 100°C.
Range of non-rising spindle gate valves with DZR brass bodies. Operating members are either handwheel operated or lockshield. Maximum working pressure: 20.0 bar. Maximum operating temperature: 100°C.
Range of seated gate valves with blue epoxy coated ductile iron bodies, bonnets and ductile iron wedges encapsulated in EPDM. All models have a handwheel operating member. Maximum working pressure 16 bar. Maximum operating temperature 80 °C
Range of stop valves with either DZR brass or brass bodies (see models) with T-type operating members. The 15mm, 22mm and 28mm compression sizes are for use with copper pipe (manufactured to EN 1057). The 20mm and 25mm compression sizes are for use PE pipes (manufactured to EN 12201-2). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of handwheel operated bronze bodied stop valves. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of double regulating valves available with DZR brass, lead free brass or bronze bodies (see models). Products incorporate a non-rising spindle headwork. Products also include two test ports. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of commercial dish washing machines with flow controlled by a solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 4.0 bar. Cold water use only.
In-line electrolytic scale reducer with chromium plated copper body for use with copper pipe manufactured to BS EN 1057. Maximum working pressure 10.0 bar. Maximum operating temperature 99°C.
Magnetic scale reducer, incorporating chrome plated copper body, for use with copper pipe manufactured to BS EN1057. Maximum working pressure 10.0 bar. Cold water use only.
Range of in-line electrolytic scale reducers with copper bodies for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 40°C.
Range of UV disinfection units with stainless steel bodies. Maximum working pressure 10.0 bar. Cold water use only.
'CY103'. Dark grey coloured, cold pressed, phenolic resin impregnated carbon graphite seal ring. For use with water up to 85°C.
'Powercron® 6070 B coating'. Factory applied, black coloured resin based coating. Apply as per manufacturer's TDS 'CR607B/CP588B'. Cure for 30 minutes@180°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘Rashmi Ordinary Portland Cement’. Factory applied, grey coloured cement. Mix cement, sand & water in a mass ratio of 1:1.7:0.5 and apply as per manufacturer's instructions 'TSL/TSMD/DI/QA/TPI/DC/002', dated '09/06/2025'. Cure for 4 hours@45°C then cure in open air for 28 days@33-39°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Rashmi Portland Slag Cement’. Factory applied, grey coloured cement. Mix cement, sand & water in a mass ratio of 1:1.7:0.5 and apply as per manufacturer's instructions 'TSL/TSMD/DI/QA/TPI/DC/003', dated '09/06/2025'. Cure for 4 hours@45°C then cure in open air for 28 days@33-39°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Ramco Ordinary Portland Cement’. Factory applied, grey coloured cement. Mix cement, sand & water in a mass ratio of 1:1.7:0.5 and apply as per manufacturer's instructions 'TSL/TSMD/DI/QA/TPI/DC/001', DATED '09.06.2025'. Cure for 4 hours@45°C then cure in open air for 28 days@33-39°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TML Sagar Sulphate Resisting cement'. Factory applied, grey coloured sulphate resisting cement. Mix cement, sand and water in a mass ratio of 1:1.50:0.50 and apply as per manufacturer's instructions 'TSL/TSMD/DI/QA/TPI/DC/005', dated '09/06/2025'. Cure for 4 hours@28°C. Then 4 hours@45°C. Then 6 hours@40°C (humidity greater than 85%). Then 666 hours@35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PROTEGOL EP Coating 32-99. Factory applied, two-component, yellow coloured epoxy coating. Mix Component A (resin) with Component B (hardener) in a volume ratio of 1.75:1.0 and apply as per manufacturer's TDS released '03/2025'. Cure for 24 hours at 23°C and then 24 hours at 70°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Uniseal WS 3400'. Beige coloured, calendered fibre gasket material. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio
'AF-300 B Pro'. Blue coloured, NBR/fibre gasket material manufactured by calendaring. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at reduced surface area to volume ratio
'Huili-GRP Water Tank Panel (HL002)'. Grey coloured (opaque), hot press moulded GRP panel. For use with water up to 23°C.
‘Neoperl Softpex® hose inliner’. Single layered, extruded, uncoloured (appears off-white, transparent) PEX-a tube. For use with water up to 70°C.
'H.B. Fuller UK Silicone Spray'. Clear, Silicone Lubricant Spray. Apply as per manufacturer's TDS, 'issue 4', dated '23/05/2025'. For use with water up to 85°C.
'Polypipe Silicone Spray Lubricant SG 300'. Clear, Silicone Lubricant Spray. Apply as per manufacturer's TDS, 'issue 2', dated 'November 2022'. For use with water up to 85°C.
'Greasil 4000'. White coloured silicone grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
'RADILON® S RV350RKC2 306 BK'. Black coloured, injection moulded, 35% glass fibre reinforced, PA6 material. For use with water up to 85°C.
'Badadur PBT9 GF10 WL Blau 1001'. Blue coloured, injection moulded PBT material. For use with water up to 23°C.
'ISO Resin Topaz-2100-AT'. Beige coloured polyester resin manufactured by hand layup. For use with water up to 45°C.
'GP Resin Topaz-1110-TP'. Beige coloured polyester resin material manufactured by hand lay-up. For use with water up to 45°C.
‘4TECH 9S20000 W-A ABK’. Black coloured, injection moulded, unfilled PPO/HIPS material. Between February 2024 and April 2025, it was for use with water up to 23°C. Between May 2025 and February 2029, it’s for use with water up to 85°C.
‘EP4066F, EP4566F, EP5066F, EP5566F, EP6066F, EP6566F, EP7066F, EP 7566F, EP8066F, EP8566F, EP9066F’. Range of black coloured, compression moulded, EPDM ‘O’ rings and gaskets. Shore hardness between 40 & 90. ‘O’ rings with tested in-radii sizes of between 0.25mm & 5.00mm. Gaskets with tested in-radii sizes of between 0.25mm & 7.50mm. For use with water up to 85°C.
'EP7007PF 'O' ring'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size 0.89mm. For use with water up to 85°C.
'EPDM-50AA2, EPDM-60AA2, EPDM-70AA2, EPDM-80AA2 & EPDM-85AA2'. Black coloured, compression moulded EPDM materials. Shore hardness between 50 ShA & 85 ShA. Tested in-radius size 1.0mm. For use with water up to 65°C.
'EPDM E293'. Black coloured, compression moulded EPDM material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
Page 213 of 233
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
