Range of gate valves incorporating bronze bodies and wedges with PTFE seals. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating bronze bodies and wedges with PTFE seals. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating a blue epoxy coated ductile iron body. EPDM coated ductile iron wedges and a non-rising spindle headwork. Maximum working pressure 16.0 bar. Maximum operating temperature 45°C. As of September 2024 Maximum operating temperature 23°C.
Range of screw down stop valves with plastic bodies to be used with PEX, MDPE and copper pipe. For above ground use only. Maximum working pressure 16.0 bar, cold water use only.
Front loading, commercial washing machine. Flow is supplied via solenoid valves and the unit incorporates a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of ultra-violet disinfection units consisting of a stainless-steel body and quartz tubes with EPDM O rings. Maximum working pressure 16.0 bar. Maximum operating temperature 50.0°C
'Nav-Coat Bitumen Paint 001 Black'. Factory applied, black coloured bitumen coating. Apply as per manufacturer's product information sheet issued '10.07.2009'. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Dicoat Medium Temp Black'. Factory applied, black coloured bitumen coating. Apply as per manufacturer's user instructions reference 'SPL/RD/UI/2019100121', issue no. '01' dated 08.07.2020. Cure for 7 days@30°C. Between 1st January 2021 to 22nd November 2021, the material is for use with water up to 50°C. Between 23rd November 2021 and 31st January 2026, the material is for use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'RS-0004'. White coloured, compression moulded seal ring manufactured from 'ADR 96' ceramic material. For use with water up to 85°C.
'Eurokote® 46-60 Red Brown'. Factory applied, red-brown coloured epoxy coating. Apply as per manufacturer's technical data sheet dated 19/11/2019. Cure for 7 days@20°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'High Build Solvent Free Epoxy Coating Red'. Factory applied, red coloured epoxy coating. Apply as per manufacturer's user instructions reference 'SPL/RD/UI/202006119', issue no, '01' dated 20.08.2020. Cure for 24 hours@30°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Crystic 3846 BE (transparent, brown coloured) & Crystic 491 EPA (ME)’ Transparent, brown coloured and translucent, pale yellow coloured, contact moulded GRP materials. For use with water up to 23°C.
'RE971 Natural'. Clear, extruded, single layer TPU hose. For use with water up to 85°C.
'RE971 Red, Blu, White and Grey'. Dual layered, extruded hoses consisting of a clear inner TPU inner layer and red, blue, white or grey coloured TPU outer layer. For use with water up to 85°C.
'Badadur PBT9 GF30 graphit 371 (grey coloured) & Badadur PBT9 GF30 Alpinweiss 230c (white coloured). Injection moulded Polybutylene terephthalate (30% glass fibres) materials. For use with water up to 65°C.
Dowlex NG2432UE. Dowlex NG2432.10UE. RX 103 Natural. RX 103 Black 9003. RX 103 GR Black 9003. Natural and black coloured, rotationally moulded polyethylene material. For use with water up to 70°C.
‘EPDM-FF’. Black coloured, compression moulded EPDM rubber material. Shore hardness 80A. Tested in-radius size 0.89mm. For use with water up to 85°C.
‘ELASTOSIL® R plus 4303/60 mH (60), ELASTOSIL® R plus 4303/70 mH (70) and ELASTOSIL® R plus 4303/80 mH (80)’. Extruded, natural (appears white in colour) platinum cured HTV silicone rubber with a shore hardness of between 60 & 80. Tested in-radius size 2.0mm. The rubbers may also be coloured using the following ELASTOSIL® Color Pastes PT in a maximum of 1% content: PT Carbon black RAL 9005. PT Red brown RAL 3013. PT Red RAL 3000 F. PT Yellow RAL1016 PT Yellow RAL 1026 F PT Yellow RAL 1021. PT Grey RAL 7040. PT Dark blue 5010. PT Ultramarine blue RAL 5002. PT Violet RAL 4001. PT Green RAL 6017. PT Black RAL 9017. PT White RAL 9010. PT Yellow RAL 1033. PT Orange RAL 2004 F. PT Violet RAL 4002. PT Blue RAL 5022. PT Helio green RAL 6004. For use with water up to 85°C.
Range of single hole, single outlet (fixed) electronically operated, tap assemblies (chromium plated brass). Flow is controlled via solenoid valve and actuated by a touch sensor. The spout outlets incorporate a plastic aerator, supplied with stainless steel strainers. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) electronically operated tap assemblies incorporating brass bodies (various finishes). Flow is controlled via solenoid valve and actuated by a touch sensor. The hose inlet incorporates a flow restrictor and the spout outlets incorporate a plastic aerator. Maximum working pressure 7.5 bar. Maximum operating temperature 60°C.
Page 21 of 201
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
