Range of screw down valves with brass or DZR brass bodies, brass or DZR brass bonnets, EPDM washers and PTFE seats. Compression connection to be used with copper pipe manufactured to EN1057. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
Range of screw down valves with brass bodies, , EPDM washers and PTFE seats. Compression connection to be used with copper pipe manufactured to EN1057. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
Range of screw down stop valves with plastic bodies, EPDM washers and ‘O’ rings. For use with polyethylene pipe (manufactured to EN 12201). The products are supplied with loose pipe inserts. For above and below ground use. Maximum working pressure 16 bar. Cold water use only.
Range of combination valves consisting of an in-line adjustable pressure reducing valve (between 1.5 and 6.0 bar) and a pressure relief valve, with DZR Brass bodies, EPDM `O`-rings and an EPDM diaphragm. CWIC110004 model - Pressure reducing valve pre-set at 3.5 bar and pressure relief valve set at 6.0 bar. CWIC200055 model - Pressure reducing valve pre-set at 3.0 bar and pressure relief valve set at 4.5 bar. The product incorporates a stainless-steel mesh and a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). For use with copper pipe (manufactured to BS EN 1057). Maximum supply pressure 16.0 bar. Outlet pressure range 1.5 bar to 6.0 bar (both models). Maximum operating temperature 20°C.
Range of regulating valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
‘PureOne hose’ (formerly known as ‘Clearwater hose’). Multi-layered hose manufactured on a mandrill by hand, consisting of a colourless, transparent PE inner layer and a blue coloured EPDM outer layer. Please note that the hose has many layers but the approval describes only the inner and outer layers. For use with water up to 50°C.
'ILPEA 70-90 EPDM HOSE WRAS AF'. Black coloured, extruded EPDM hose. Shore hardness 80. Tested in-radius size 1.3mm. For use with water up to 23°C.
'TIMO-70 'O'-rings & gaskets'. Black coloured, injection moulded, EPDM 'O' rings and gaskets. Shore hardness 70. The 'O' rings have a tested in-radius size of 0.5mm. The gaskets have a tested in-radii size between 0.5mm & 2.6mm. ‘O’ rings with a tested in-radius size of 2.6mm were added to the approval in May 2023. For use with water up to 85°C.
'70EP124p'. Black coloured, compression moulded EPDM 'O' ring. Shore hardness 70. Tested in-radius size 0.89mm. For use with water up to 85°C.
`GCE EP W80`. Black coloured, extruded, EPDM hose. Shore hardness 85. Tested in-radii sizes between 0.75mm & 1.70mm. For use with water up to 85°C.
'70 EPDM 291'. Black coloured, injection moulded EPDM rubber 'O' rings. Shore hardness 70. Tested in-radii sizes between 0.51mm & 2.50mm. For use with water up to 85°C.
'EPOE7001P-WRC Diaphragm'. Black coloured, injection moulded EPDM diaphragm. Shore hardness 70. Tested in-radius size 1.20mm. For use with water up to 85°C.
'80EP251p 'O' ring'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 80. Tested in-radius size 0.89mm. For use with water up to 85°C.
'Safelok Seal'. Black coloured, transfer moulded EPDM 'O' ring. Shore hardness 75. Tested in-radius size 3.75mm. For use with water up to 23°C.
'EPDM 70.10-02 'O'-rings & gaskets'. Black coloured, injection moulded, EPDM 'O' rings and gaskets. Shore hardness 70. The 'O' rings have a tested in-radius size of 0.5mm. The gaskets have a tested in-radii size between 0.5mm & 2.6mm. ‘O’ rings with a tested in-radius size of 2.6mm were added to the approval in May 2023. For use with water up to 85°C.
‘07096-80 gaskets’. Black coloured, compression moulded EPDM gaskets. Shore hardness 80. Tested in-radius size between 0.9mm & 1.75mm. For use with water up to 85°C.
'EP2480 BLK 'O' ring'. Black coloured, injection moulded EPDM 'O' ring. Shore hardness 70. Tested in-radius size 1.31mm. For use with water up to 85°C.
'SV-EPDM'. Black coloured, compression moulded, EPDM 'O' ring. Shore hardness 73. Tested in-radius size 1.53mm. For use with water up to 23°C.
'EC-6509-A'. Black coloured, compression moulded EPDM rubber material. Shore hardness 65. Tested in-radius size 0.5mm. For use with water up to 80°C.
'EP62/75'. Black coloured, compression moulded EPDM 'O' ring. Shore hardness 75. Tested in-radius size 3.5. For use with water up to 85°C.
'XR0270012'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.5mm. For use with water up to 85°C.
'RE7012(70SH)'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.5mm. For use with water up to 85°C.
'EW Gasket Material'. Black coloured EPDM gasket material which is injection moulded and then spliced (made in Poland). In June 2025, black coloured, compression moulded material (made in China) was added to the approval. Shore hardness 65A. Between November 2022 and February 2023, the in-radius size was 3.9mm. Between March 2023 and November 2029, the in-radius size is 4.4mm. For use with water up to 23°C.
'E65-04BL-G / Black'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 0.95mm. For use with water up to 23°C.
'EPDM 1570'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 0.5mm. For use with water up to 23°C.
'MRP-EN-50, MRP-EN-55, MRP-EN-60, MRP-EN-65, MRP-EN-70, MRP-EN-75 & MRP-EN-80'. Black coloured, compression moulded EPDM materials with a shore hardness of between 50 & 80. Tested in-radius size 0.88mm. For use with water up to 65°C.
'CE EPDM (TY-02-50) & CE EPDM (TY-05-80)'. Black coloured, compression moulded EPDM sheet materials. Shore hardness between 50 & 80. Tested in-radius size between 0.75mm & 1.0mm. For use with water up to 23°C. From February 2024 the materials are for use with water up to 65°C.
‘EP70A9OF’. Black coloured, compression moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 1.06mm For use with water up to 23°C.
'AA6KWZ, AA7KWZ, AA8KWZ and AA9KWZ'. Black coloured, compression moulded EPDM materials with a shore hardness of between 60 & 88. Tested in-radius size 1.0mm. AA6KWZ is for use with water up to 65°C. AA7KWZ, AA8KWZ and AA9KWZ are for use with water up to 23°C.
'HW-EPDM'. Black coloured, compression moulded EPDM sheet materials. Shore hardness 50, 60, 70 and 80. Tested in-radius size 1.0mm. The 50 shore hardness material is for use with water up to 65°C. The 60, 70 & 80 shore hardness materials are for use with water up to 60°C.
‘51M5577, 51M6077, 51M6577, 51M7077, 51M7577, 51M8077, 51M8577’. Black coloured, injection moulded EPDM materials. Shore hardness between 55A & 85A. Tested in-radius size 1.0mm. For use with water up to 85°C.
'APE 55 N'. Black coloured, injection moulded EPDM rubber material. Shore hardness 55. Tested in-radius 1.1mm. For use with water up to 23°C.
‘TWK7534, TWK5810, TWK5811, TWK5812, TWK5813, TWK5814, TWK5815’. Black coloured, injection moulded EPDM materials. Shore hardness between 55A & 85A. Tested in-radius size 1.0mm. For use with water up to 85°C.
'GM-EP01'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.15mm. For use with water up to 23°C.
'EPDM E282'. Black coloured, compression moulded EPDM sheet material. Shore hardness 80A. Tested in-radius size 1.0 For use with water up to 85°C.
'E7014F'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 23°C. From April 2023, the material is for use with water up to 85°C.
'EPDM 70.503-00'. Black coloured, injection moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'51616 – E40, 51616 – E50, 51616 – E60, 51616 – E70 & 51616 – E80'. Black coloured, compression moulded EPDM materials. Shore hardness between 40 & 80. Tested in-radius size 1.0mm. For use with water up to 65°C.
Spring loaded resilient trim in-line check valve cartridge with acetal body, incorporating a stainless-steel spring and EPDM ‘O’-rings. To be housed in a specifically dimensioned body. Maximum working pressure 16 Bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of ceramic cartridges or 2-way ceramic disc diverter headworks with plastic bodies, EPDM ‘O’-rings and/or gaskets, for insertion into specifically dimensioned bores. The JA01AJ and AH01AJ models incorporate a thermostatic element. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of thermostatic cartridges with a brass housing, stainless-steel filters and EPDM ‘O’-rings. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Thermostatic cartridges with plastic bodies, stainless steel mesh strainer and EPDM ‘O’ rings. For insertion into specifically dimensioned bores. Maximum operating pressure 10 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Three-hole, single outlet (fixed) combination tap assembly (brass body – various finishes). Incorporating quarter turn ceramic disc headworks with various operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with a lever type pop-up waste and stainless steel braided EPDM lined connection hoses. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Three-hole, single outlet (fixed) combination tap assembly (brass body – various finishes). Incorporating quarter turn ceramic disc headworks with various operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with a lever type pop-up waste and stainless steel braided EPDM lined connection hoses Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of three-hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes). Incorporating quarter turn ceramic disc headworks with single lever, cross top, or dome type operating members. The spout outlets for models (F4184, F6182B & F9484) incorporate a plastic aerator and models (F6182C & F8118) are open outlet. The products are supplied with stainless-steel braided EPDM lined flexible hoses to headworks to the spout outlet. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Three-hole, single outlet, (fixed), combination tap assembly, (brass body – various finishes). Incorporating quarter turn ceramic disc headworks with cross top operating members. The product is supplied with stainless-steel braided EPDM lined flexible hose assemblies to connect the headworks to the spout outlet and a lever type pop up waste. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Five-hole, single outlet (fixed) combination tap assembly (brass body - various finishes), incorporating quarter turn ceramic disc headworks with cube type operating members and a manually operated diverter to the shower outlet. The product is supplied with stainless-steel braided EPDM lined flexible connection hoses to connect the headworks, spout and diverter. Maximum working pressure 5.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of horizontal or vertical expansion vessels with an EPDM membrane. Maximum working pressure 10.0 or 16.0 bar (please refer to model). Maximum operating temperature 100°C.
Filling loop assemblies consisting of a stainless steel braided EPDM lined flexible hose, an isolation valve and another isolation valve incorporating a non-verifiable double check valve assembly, verified by test (suitable for backflow protection against fluid category 3). The FL12041515 model is supplied with an isolation valve including a dial type pressure gauge. The FL12041525 model is also supplied with brass end caps incorporating EPDM washers. For use with coper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Filling loop assemblies consisting of a stainless steel braided EPDM lined flexible hose, an isolation valve and another isolation valve incorporating a non-verifiable double check valve assembly, verified by test (suitable for backflow protection against fluid category 3). The 171293 model is supplied with an isolation valve including a dial type pressure gauge. The 171292 model is also supplied with brass end caps incorporating EPDM washers. For use with coper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Page 20 of 47
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
