'JSGL-SRC (E)'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1:1.7:0.5 weight ratio and apply as per manufacturer's work instructions 'JSGL/WI/14', 'Issue No. 02', 'Revision No. 00', dated '29.09.2018'. Cure for 4 hours@45°C (R.H. 85%). For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NextGen NP-F9500 PW'. Factory applied, blue coloured powder coating. Apply as per manufacturer's technical data sheet 'FBE/ REV00 01-02-201'. Cure for 3 minutes@240°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NextGen NP-F9500 PW'. Factory applied, blue coloured powder coating. Apply as per manufacturer's technical data sheet 'FBE/ REV00 01-02-2019'. Cure for 3 minutes@240°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Nylon 11'. Factory applied nylon coatings available in white or grey colours. The substrate the coating is to be applied to is heated to 310°C for 30 minutes and the coating applied as per manufacturer's work instructions 'WI-09-19 Rev. 6' dated April 22, 2020. Cure for 10 minutes@270°C. The white coating is for use with water up to 23°C. The grey coating is for use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hylon N1040 H2 BK397 W & Hylon N1030 H2 BK397 W'. Black coloured, injection moulded, glass fibre filled polyamide materials. For use with water up to 60°C.
'AASTER 962'. Brown coloured (translucent), injection moulded Polyester resin material. For use with water up to 50°C.
'Polimal 122-2 AWTP' (beige coloured) & 'Polimal 1094 AWTP-1' (amber coloured). Contact moulded, unsaturated polyester resin materials. For use with water up to 23°C.
'Egelen PE100 & Egeplast 9010 pipes'. Egelen PE100 is a single layered, black coloured, extruded PE100 pipe. Egeplast 9010 is a dual layered, extruded PE100 pipe consisting of a black coloured inner layer and a blue coloured outer layer. For use with water up to 23°C.
'Water Guide P96400-005'. Beige coloured (opaque), injection moulded PPO component. For use with water up to 65°C.
'NORYL™ 731S-701-01-01-00 black coloured, NORYL™ 731S-801-01-01-00 beige coloured, NORYL™ 731S-845-01-01-00 beige coloured & NORYL™ 731S-960-01-01-00 grey coloured'. Injection moulded PPE materials. For use with water up to 85°C
'Longsheng-99 PPR Pipe'. Green coloured, extruded PPR pipe. For use with water up to 23°C.
'E9053AA 'O' rings'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 90. Tested in-radii sizes between 0.4mm and 3.65mm. For use with water up to 85°C.
'EPDM50P - ELAST45901, EPDM60P - ELAST46901, EPDM70P - ELAST47901 & EPDM80P - ELAST48901’. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 80. Tested in-radius size 1.3mm. For use with water up to 85°C.
'CSTD/BS6920-BA60' (shore hardness 60), 'CSTD/BS6920-BA70' (shore hardness 70) and 'CSTD/BS6920-BA75' (shore hardness 75). Black coloured, compression moulded EPDM materials. Tested in-radius size 1.05mm. For use with water up to 85°C.
SI-55678 (shore hardness 50), SI-65678 (SH 60), SI-75678 (SH 70) & SI-85678 (SH 80) natural ‘O’ rings. SI-52109 (shore hardness 50), SI-62109 (SH 60), SI-72109(SH 70), SI-82109 (SH80) red coloured ‘O’ rings. SI-51501 (shore hardness 50), SI-61501 (SH 60), SI-71501(SH 70) & SI-81501(SH 80) blue coloured ‘O’ rings. Natural (appears white coloured), red or blue coloured, compression moulded silicone rubber ‘O’ rings. Shore hardness between 50 shore A and 80 shore A. Tested in-radii sizes between 0.5mm & 2.5mm. For use with water up to 85°C.
Range of stop valves with plastic bodies. The valves incorporate a built in solenoid valve which is operated by a switch located on the valve or by a remote control. The leak detector supplied with model SVSM66MRD is not connected to any water pipe, is independent of the valve and is intended to be installed in the area at risk of leakage. It is intended to detect leakage and sends an electrical signal to close the valve. For use with copper pipe (manufactured to BS EN1057), PEX pipe (manufactured to BS7291-3) and PB pipe (manufactured to BS7291 -2). Maximum working pressure 10.0 bar. Cold water use only
Range of wall mounted single hole, single outlet, fixed, electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled via an infra-red activated solenoid valve. Maximum working pressure 8.0 Bar Maximum operating temperature 45.0°C
Side and bottom entry BS1212 - 3 compact type float operated valve for WC flushing cisterns Maximum operating pressure 14 bar. Maximum operating temperature 23°C
Range of bottom entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. Maximum working pressure 10.0 bar. Cold water use only.
The range of WC cisterns incorporating a BS 1212-4:2016 side entry or bottom entry float operated inlet valve providing a Type AG air gap arrangement and a flush outlet valve operated via a push button assembly for either full or reduced flush. Maximum operating pressure 10.0 bar. Cold water use only.
Page 189 of 201
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
