Range of UV disinfection units with stainless steel bodies and EPDM seals. The UV lamps are housed inside quartz tubes. Maximum working pressure 10.3 bar. Maximum operating temperature 40°C.
'M9000'. Grey coloured, injection moulded POM material. For use with water up to 85°C.
'Delrin® RAFG511DP NC010'. White coloured, injection moulded semi-opaque acetal material. For use with water up to 85°C.
'JPC Liquid Epoxy Paint'. Factory applied, red coloured, two-component epoxy paint. Mix components A & B in a 3:1 volume ratio and apply as per manufacturer's instructions ' JPC-FG-A/06-21/009 & JPC-FG-B/06-21/009' dated '02/06/2021'. Cure for 7 days@34°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'KARUMEL EX4412 (RAL5005) & KARUMEL EX4412 (Blue)'. Factory applied, blue coloured epoxy powder coatings. Apply as per manufacturer's application guide for potable water reference number 'KCSA-21090101' dated September 2021. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LNXFSY'. Factory applied, grey coloured Portland Cement Mortar. Mix cement, sand and water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue 'X202101207F' dated '2021-12-07'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Ya-Coat Amiantit (SADIP)'. Factory applied, two-component, green coloured (once mixed and applied) PU coating. Mix base and hardener in a 3:1 volume ratio and apply as per manufacturer's process document 'MW 106-5 issue 1', dated 26/06/2007. Cure for 10 minutes@35°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Desmopol DW'. Factory applied, two-component, cream coloured (once mixed and applied) polyurethane resin coating. Mix components A & B in a 4:1 volume ratio and apply as per manufacturer's TDS 'DESMOPOL DW v.11-03-2022'. Cure for 6 hours@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Eurokote® 48-20'. Factory applied, blue coloured, two component epoxy coating consisting of a resin and hardener. Mix resin and hardener in a mass ratio of 68:32 and apply as per manufacturer's TDS dated 10/12/2018. Cure for 24 hours@20°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MS 1555'. Factory applied, dark blue/grey coloured vitreous enamel coating. Apply as per manufacturer's instructions 'I.PBE.06.04' dated November 22, 2021 and 'TPE.09.056.02' dated August 19, 2014. Cure for 14 minutes@850°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MasterSeal P693/94Primer and MasterSeal M 649 (formerly known as MasterSeal 694) Coating'. Factory applied, grey coloured (once mixed), two-component primer (non-water contact primer) and two-component coating (water contact coating). Mix and apply 'MasterSeal P693/94Primer’ as per Technical Data Sheet ‘MBS_CC-UAE/Sl_P_693/694_06_22’. Cure for 2 hours@25°C. Then mix and apply ‘MasterSeal M 649 Coating' as per Technical Data Sheet ‘MBS_CC-UAE/Sl_M 649_06_21/v1/08_21/v2/06_22/v3/10_22’. Cure for 1 minute@25°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Versathane'. Site applied, two-component, grey coloured (once mixed) polyurethane coating. Mix the grey coloured (opaque) base coating with the amber coloured hardener in a 3:1 volume ratio and apply Coat 1 as per manufacturer's product data sheet 'Issue No. 01 Sep 2016. Cure for 4 hours@7°C. Mix and apply Coat 2 using the same mix ratio and application instructions and then cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Resichem 507 DWPU Blue & Grey'. Site applied, two-component polyurethane coatings which are available in blue or grey colours (once mixed). Mix Part A (blue or grey opaque liquid) with Part B (amber, translucent liquid) in a 100:30.5 weight ratio and apply as per manufacturer's technical data sheet 'TDS507DWPU.rv4.09062022'. Cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'YT-002 (natural) & YT-003 (black)'. Extruded, natural (colourless) or black coloured PVC hoses. For use with water up to 65°C.
'Purolite C107E'. Cream coloured ion exchange resin. For use with water up to 23°C.
'Purolite A520E'. Light brown coloured ion exchange resin. For use with water up to 23°C.
'Purolite® C104E/5264'. Cream coloured ion exchange resin. For use with water up to 23°C.
'K422'. Clear, silicone lubricant aerosol. Apply as per manufacturer's instructions 'version 1.0' dated 'May 2022'. For use with water up to 85°C.
'Hydro 90'. Clear, silicone lubricant aerosol. Apply as per manufacturer's instructions 'version 1.0' dated 'June 2022'. For use with water up to 85°C.
'Bestnyl SI40VI02BD (PA 640GF BK)'. Black coloured, injection moulded PA6 material. For use with water up to 60°C.
Page 187 of 561
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
