'MS519'. Factory applied, blue coloured Porcelain Enamel coating. Apply as per manufacturer's instructions dated 2021.6.23. Dry for 2 hours@100°C before firing for 10 minutes@860°C For use with water up to 75°C. This material is only approved for the drying and firing conditions that appear on the approval. If the drying and/or firing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'GMF-01'. Factory applied, grey coloured cement mortar. Mix sand, water & cement in a 1.5:1.0:1.0 weight ratio. Cure for 24 hours@25°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EARTHSTAHL TYPE OPC'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a 1.0:1.5:0.5. Cure for 28 days@26°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EARTHSTAHL TYPE SRC'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a 1.0:1.5:0.5. Cure for 28 days@26°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EARTHSTAHL TYPE BFSC'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a 1.0:1.5:0.5. Cure for 28 days@26°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Norsodyne H 13212 TAE Laminate' for use with 'Polycor White Gel Coat'. ‘NORSODYNE H 13212 BTAE Laminate' was added to the approval in July 2024. The glass fibre panel is manufactured by hand lay method and then factory applied, unsaturated resin gel coat is applied by brush (BR) or spray (PA). The brush gel coat is to be applied as per manufacturer's TDS ‘4100’ dated 10.10.17 and cured for 24 hours@25°C. The spray gel coat is to be applied as per manufacturer's TDS ‘4200’ dated 10.10.17 and cured for 24 hours@25°C. For use with water up to 23°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'HEXELL SC 3093 TYPE BLACK G01'. Black coloured, rotmoulded LLDPE material. For use with water up to 23°C.
'HEXELL SC 3093 TYPE GREY B22 MIX B11'. Grey coloured, rotmoulded LLDPE material. For use with water up to 23°C.
'TASNEE 100 Black'. Black coloured HDPE material manufactured in Saudi Arabia and Germany, for injection moulding and extrusion purposes. For use with water up to 60°C.
'Aidmer78-031'. White coloured (opaque), extruded PTFE pipe. For use with water up to 85°C.
'AQUAPEA® In-line Repair'. Site applied, dark grey coloured (once mixed), two-part epoxy putty (light grey and dark grey coloured) and polypropylene core (white, translucent). Mix & cure as per the document: “Aquapea method statement issue 1 dated 23-04-21” . For use with water up to 23°C.
'4273 'O' rings and washers'. Black coloured, injection moulded EPDM 'O' rings and washers. Shore hardness 70. The 'O' rings have an in-radius size of 1.31mm. The washers have an in-radius size of 2.00mm. For use with water up to 85°C.
'EP10/00/2 BLK EPDM 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 65. Tested in-radius size 1.5mm. For use with water up to 85°C.
'HYPRESS12V'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.1mm. Between June 2021 and August 2022, the material was for use with water up to 23°C. Between September 2022 and June 2026, the material is for use with water up to 65°C.
'S/EP-50, S/EP-60, S/EP-70 & S/EP-80'. Black coloured, compression moulded EPDM materials with a shore hardness of between 50A & 80A. Tested in-radius size 1.05mm. For use with water up to 65°C.
'ILPEA 70-90 EPDM COMPOUND WRAS AF'. Black coloured, compression moulded EPDM material. Shore hardness 80. Tested in-radius size 1.25mm. For use with water up to 23°C.
'EPDM-W E267'. Black coloured, compression moulded EPDM material. Shore hardness 80A. Tested in-radius size 1.0mm. For use with water up to 85°C.
'Hongli IRHD50'. Black coloured, press moulded EPDM material. Shore hardness 50. Tested in-radius size 1.12mm. For use with water up to 50°C.
'A-KT 70-00'. Black coloured, extruded and rotocured EPDM rubber material. Shore hardness 70. Tested in-radius size 1.00mm. For use with water up to 23°C.
'Sunaflex T 8289'. Black coloured, compression moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 23°C.
'LC 50-90'. Black coloured, compression moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 1.33mm. For use with water up to 85°C.
'Viton `A` V99 gaskets'. Black coloured gaskets cut from calendered fluoroelastomeric material. Shore hardness 70. Tested in-radius size 1.5mm. For use with water up to 23°C.
'70NBR103F'. Black coloured, compression moulded NBR 'O' rings. Shore hardness 70. Tested in-radius size 0.5mm. For use with water up to 85°C.
'TEC S147 R.-45 ROSSO'. Orange coloured, injection moulded, silicone rubber 'O' rings & gaskets. Shore hardness 45. Tested in-radius size between 0.5mm & 2.6mm. For use with water up to 85°C.
'Novodur® SBM-90 Q203'. Natural (appears off-white), injection moulded thermoplastic resin. The natural material may be coloured using the following INEOS Styrolution colourants at the agreed maximum percentage concentrations by weight: Pigment White 6, Black 7, Blue 15:3, Blue 29, Brown 24, Red 101, Violet 15, Green 7, Green 17 & Yellow 53. For use with water up to 60°C.
'Novodur® SBM-90'. Natural (appears off-white), injection moulded thermoplastic resin. The natural material may be coloured using the following INEOS Styrolution colourants at the agreed maximum percentage concentrations by weight: Pigment White 6, Black 7, Blue 15:3, Blue 29, Brown 24, Red 101, Violet 15, Green 7, Green 17 & Yellow 53. For use with water up to 60°C.
Floor mounted single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes - see model). The product incorporates a ceramic cartridge headwork with a single lever operating member and a lockable diverter to shower outlet. The spout outlet incorporates a plastic aerator. The products are supplied with a shower hose and handset. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (brass body - various finishes, see model). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The inlet hose incorporates an approved single check valve cartridge, however, the complete assembly has not been tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (brass body - various finishes, see model). Flow is controlled by a solenoid valve activated via an infra-red sensor. The product incorporates a manual temperature control operated by a single lever on the side of the body. The spout outlet incorporates a plastic aerator. The inlet hoses incorporate an approved single check valve cartridge, however, the complete assembly has not been tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
A range of wall mounted two hole single outlet (fixed) electronically controlled tap assemblies with brass bodies (various finishes). Flow is controlled by a solenoid valve activated by via an infra-red sensor on the underside of the tap. The inlets of the function block incorporate stainless steel strainers, plastic silencers and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum working temperature 60°C.
Range of wall mounted, single hole, single outlet (fixed) electronically controlled tap assemblies comprising of a concealed brass body and a separate spout and trim set (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The inlets (within the) concealed body incorporate a plastic filter and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of BS1212-4 (2016) compact type float operated valves for WC flushing cisterns, bottom or side entry type. The inlet incorporates a strainer. Maximum working pressure 10.0 bar. Cold water use only.
Range of concealed WC flushing cisterns with a side entry BS 1212-4(2016) float operated inlet valve providing a type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two button assembly for a 6 or 3 litre flush volume. The cistern incorporates a servicing valve and a stainless-steel braided EPDM lined flexible hose assembly installed prior to the inlet valve. Maximum working pressure 10.0 Bar, Cold Water use only
Range of concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only. .
Concealed WC dual flushing cistern with a BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush pneumatic outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of check valve cartridges with plastic bodies to be housed in specifically dimensioned bodies. The product incorporates a plastic flow regulator. Maximum working pressure 16.0 bar & maximum operating temperature 65°C.
Range of single check valve assemblies incorporating DZR brass bodies. Maximum working pressure 10 bar. Maximum operating temperature 85°C.
Range of single check valve assemblies incorporating DZR brass bodies. Maximum working pressure 10 bar. Maximum operating temperature 85°C.
Range of single check valve assemblies incorporating DZR brass bodies. Maximum working pressure 10 bar. Maximum operating temperature 85°C.
Range of non-verifiable double check valve assemblies (DZR brass bodies) incorporating spherical valves and either red or blue butterfly handles. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of double check valve assemblies consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body (chrome plated or brass finish) with a port located between the cartridges. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body (chrome plated) with a port located between the cartridges. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of quarter turn ceramic disc and cartridge headworks with plastic bodies to be inserted into specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
A range of ceramic cartridge headworks with plastic bodies incorporating EPDM `O`-rings and seals for insertion into specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of quarter turn ceramic disc headworks with metal bodies to be inserted in specifically dimensioned bodies. Maximum working pressure 17.0 bar. Maximum operating temperature 85°C.
Range of headwork assemblies with brass bodies incorporating a quarter turn ceramic disc headwork. Maximum working pressure 17.0 bar. Maximum operating temperature 85°C.
Range of quarter turn ceramic disc headworks with brass bodies (various finishes on the stem), silicone seals, and EPDM ‘O’-rings for insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies and silicone gaskets. The products are intended for insertion into specifically dimensioned tap bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of thermostatic cartridges incorporating brass bodies (GH25W, GH35W) or plastic body (GH35T), and NBR ‘O’-rings. For insertion into specifically dimensioned bodies. Maximum working pressure 12.0 bar. Maximum operating temperature 85°C.
A range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (chrome plated), incorporating a ceramic cartridge headwork (models 63465-0001) or a quarter turn ceramic disc headwork (model 63461-0001) with single lever operating members. The products incorporate a pull-out spray with a plastic aerator at the outlet. The pull-out spray hose for model 63465-0001 incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum working temperature 60°C.
Page 19 of 209
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
