'CR-01 PE Pipe'. Blue coloured, extruded PE pipe. For use with water up to 23°C.
'CR-02 PE Fitting'. Blue coloured, injection moulded PE fitting. For use with water up to 23°C.
'3802B'. Black coloured, extruded MDPE material. For use with water up to 23°C.
'Revolve N-250 Light Grey M2-5321'. Grey coloured PE material manufactured by rotomoulding. For use with water up to 85°C.
'Revolve N-820 Natural'. Natural (appears off-white), PE material manufactured by rotomoulding. For use with water up to 85°C.
'Twistloc Pipe Insert'. Green coloured, injection moulded PPO pipe insert. In November 2025, beige coloured, injection moulded PPO 'Twistloc Pipe Inserts' were added to the approval. For use with water up to 85°C.
'ISOMAG Cylinder'. Grey coloured, extruded polypropylene cylinder component. For use with water up to 60°C.
'Verplen C3008 VE ACLKUV W (GF 30% green coloured) & Verplen 60NE A W (black coloured'. Injection moulded, polypropylene materials. For use with water up to 60°C.
'Borealis HE125MO & Bn HE125MO-100'. White coloured (semi-opaque), injection moulded PP-H materials. For use with water up to 85°C.
'+GF+ uPVC Pressure Pipe'. Grey coloured, extruded uPVC pipe. For use with water up to 60°C.
'MasterCrete ANC 932'. Site applied, grey coloured chemical anchor resin. Apply as per manufacturer's instructions 'Version 1' dated '09.12.2024'. Cure for 48 hours@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MasterCrete ANC 920'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions 'Version 1', dated '09.12.2024' Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘MasterCrete ANC 915’. Site applied, grey coloured chemical anchor resin which is supplied in a pre-mixed cartridge. Apply as per manufacturer’s instructions 'Version 1', dated '09.12.2024'. Cure for 4 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'VULKODURIT 1250 KTW'. Dark grey/brown coloured, Ebonite rubber material made by extrusion and calendaring. Shore hardness 72D. Tested in-radius size 2.0mm. For use with water up to 40°C.
'E7331'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size 0.8mm. For use with water up to 85°C.
‘0548’. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. Between March 2023 and August 2023, the material was for use with water up to 23°C. Between September 2023 and March 2028, the material is for use with water up to 80°C.
'EP80R-01'. Black coloured, compression moulded EPDM rubber material. Shore hardness 80. Tested in-radius size 1.5mm. For use with water up to 50°C.
'798F'. Black coloured, injection moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 60°C.
'E50B01, E70B01 & E80B01'. Black coloured, compression moulded EPDM material. Shore hardness between 50, 70 & 80. Tested in-radius size 1.0mm. For use with water up to 23°C.
'CERULEAN EP 14 (KIEP14)'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
'8550C'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'WAGUNIT H 1005'. Light brown coloured, compression moulded natural hard rubber. Shore hardness 78. Tested in-radius size 0.9mm. For use with water up to 23°C.
'Kamco Systemseal Gas & Water Jointing Compound (Product Code: BSS007'). Off-white coloured, PTFE paste intended for use as a thread sealant. For use with water up to 23°C.
‘Permabond A011 Red, A025 Orange, A113 Blue, A115 Orange, A118 Green, A130 Blue, A131 White, A134 Green, A136 Red, A140 Green, A1042 Blue, A1044 White, A1058 Off White, F200 Brown, F201 Brown, F202 Brown, A1084 Yellow & F201HV (translucent)’. Anaerobic adhesives to be applied and cured in strict accordance with the manufacturer's instructions. For use with water up to 85°C.
'Butyl IIR 6038 diaphragm'. Black coloured, injection moulded Butyl diaphragm. Shore hardness 64 ShA. Tested in-radius size 1.25mm. For use with water up to 85°C.
Range of wall mounted electric showers (various finishes). The E2WXX, E2BXX & E2GXX models incorporate a solenoid valve controlling the flow, which includes a combined plastic and stainless steel strainer and a plastic flow regulator on its inlet. The E1WXX & EW1WXX models incorporate a manually operated push button valve controlling the flow and plastic strainer on the inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 53°C. Cold supply only.
Range of electronic combination tap assemblies, incorporating a solenoid valve controlling the flow that is activated via an infra-red sensor. The Xeris models (012930699 & 012940699) incorporate a check valve cartridge in the inlet hose, however the complete assembly has not been tested to demonstrate it provides backflow protection. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Range of non-verifiable double check valve assemblies consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body with nickel plated or natural finish. Models with compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Models 12.10152.015.CP02-8511 & 12.10152.015.CP5R-8511 have a maximum operating temperature of 65°C. All other models have a maximum operating temperature of 85°C
Non-verifiable double check valve assembly with DZR brass body (chrome plated), incorporating two in-line check valve cartridges. Maximum working pressure – 10.0 Bar Maximum operating temperature - 85°C
Non-verifiable, double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a nickel plated, DZR brass body. The assembly incorporates an isolation valve and stainless-steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Drayton GRP range of one piece, pre-insulated cold water storage cisterns and covers for domestic water storage, supplied with a wholesome water kit. The cisterns walls are available in grey, blue, green, white, red and anthracite grey (external) colours and the cistern base is straw coloured. For cold water use only. From November 2024 the water contact layer of the cistern base and walls is available in grey or straw colours. The outer layer of the cistern base is available in blue, green, white, red and anthracite grey colours.
Range of single hole, single outlet swivel nozzle combination tap assemblies (brass bodies - various finishes) incorporating quarter turn ceramic disc headworks with cross top operating members. The outlet incorporates a plastic aerator and the product is supplied with a lever type pop-up waste, not verified by test. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
Range of single hole bidet combination tap assemblies (brass bodies - various finishes) incorporating a ceramic cartridge headwork and single lever operating member. The swivel nozzle outlet incorporates a plastic aerator and the product is supplied with a lever type pop-up waste – not verified by test. Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C.
Range of flow regulators, aerators and flow straighteners with plastic bodies. Maximum operating temperature 60°C.
Range of flow straighteners with plastic bodies. The JM030503-15 model incorporates a silicone lined flexible hose with an interlocked metal outer. The JM030002-15 model incorporates a swivel ball joint. Both models incorporate a stainless steel mesh on the outlet. Maximum operating temperature 60°C.
Range of ceramic cartridge headworks with brass bodies and EPDM gaskets and O-rings. For insertion into specifically dimensioned bores. Maximum working pressure; 5 Bar Maximum operating temperature 60°C
Range of ceramic cartridge headworks with a plastic body. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Ceramic cartridge headwork with a plastic body. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperatures 85°C (K26PMA-01NP model) and 65°C (K40P-01NPX model).
Range of ceramic cartridge headworks with plastic bodies for insertion into specifically dimensioned tap assemblies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of single-hole, single outlet (swivel) combination tap assemblies (chrome plated brass bodies). Incorporating ceramic cartridge headworks and single lever operating members. The flexible spout outlet incorporates a plastic aerator and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass). Incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 70.0°C
Single hole, single outlet fixed combination tap assembly (chrome plated brass body), incorporating non-rising spindle headworks with dome type operating members. The spout outlet incorporates a plastic flow straightener. Maximum operating pressure 10.0 bar. Maximum operating temperature 65°C.
Single hole, single outlet, fixed combination tap assembly (chrome plated brass body), incorporating quarter turn ceramic disc headworks with single operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with a lever operated pop-up waste (not verified by test) Maximum operating pressure 10.0 bar. Maximum operating temperature 65°C.
Range of floor-standing single hole, single outlet (fixed) combination tap assemblies (various finishes), incorporating a ceramic cartridge headworks with single lever operating members and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic aerator. The product is supplied with shower hose and handset. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks with lever type operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. The cold inlet hose and the spout outlet incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar Maximum operating temperature 75.0°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes). Incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.5 bar. Maximum operating temperature 60°C
Page 164 of 236
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
