Range of adjustable, pilot operated pressure reducing control valves with ductile iron bodies (blue epoxy coated) EPDM diaphragm and NBR ‘O’-rings. The products are supplied with auxiliary stainless-steel tubing, fittings, strainer, pilot valve and needle valve. Maximum inlet supply pressure 16.0 bar. Maximum outlet pressure 1.5 bar - 8.0 bar. Maximum operating temperature 80°C.
Range of plastic bodied solenoid valves incorporating a stainless steel spring and armature with an EPDM diaphragm. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of normally closed and normally open plastic solenoid valves with EPDM ‘O’-rings and sealing rings. Pushfit connections for use with John Guest LLDPE pipe or copper pipe. The 47.004.103 model acts as a diverter between two outlets, where one outlet is always open. Maximum working pressures see model section. Maximum operating temperatures: 65°C - 47.00X.1XX models with John Guest LLDPE pipe only. 90°C - 47.004.103 model with John Guest LLDPE pipe only. Models added January 2021: Cold water use only - 47.00X.2XX (4mm & 8mm) with John Guest LLDPE pipe only. 90°C - 47.00X.2XX (6mm) with John Guest LLDPE pipe only. 90°C - 47.00X.2XX (6mm & 8mm) with copper pipe only.
Isolation valve incorporating a brass body (chromium plated) and brass ball (chromium plated). Maximum working pressure 10.0 bar. Cold water use only.
Range of lever operating spherical valves incorporating brass bodies (nickel plated), brass ball (chromium plated) and PTFE seat. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘Aladdin Easyfit Isolator Pro’ valve incorporating a stainless steel body and self cutting blade to enable a connection to a pressurised or wet systems. For use with copper pipe to BS2871 – EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating ductile iron epoxy coted bodies and with EPDM ‘O’-ring seals and discs. The valves are operated via a non-rising spindle with a hand wheel operating member Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of non-rising gate valves with blue epoxy coated ductile iron body and EPDM rubber coated wedge. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C
Range of gate valves with blue epoxy coated ductile iron bodies, a ductile iron wedge encapsulated in EPDM rubber, PTFE seals and EPDM gaskets and ‘O’-rings. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of gate valves with brass bodies, brass wedges and PTFE packing glands. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
5 way manifold assembly with a DZR brass body incorporating a pressure reducing valve, with an adjustable outlet pressure range between 1.0 and 6.0 bar and a safety relief valve set at 6.0 bar. The product incorporates an inline single check valve cartridge after the balanced cold take off, verified by test (suitable for backflow protection against Fluid Category 2). Maximum supply pressure 16.0 bar. Maximum operating temperature 40°C
‘Series 116’ range of automatic thermal balancing valves (DZR Brass) with non-rising spindle headwork, brass disc and EPDM seals. Some models can be supplied with a thermometer (see model). The outlet of the 116144, 116154, 116244 & 116254 models (added January 2024) incorporate a check valve cartridge, verified by test (suitable for backflow protection against fluid category 2). Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of water conditioners. The WFL38 model has a brass body, all other models are stainless steel. Operating parameters: GRANDER® Inline units - Maximum working pressure 10.0 bar. Maximum operating temperature 95°C. GRANDER® Flexible unit - Maximum working pressure 6.0 bar. Maximum operating temperature 75°C. GRANDER® Apartment unit & Immersion units - Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Range of ion exchange water softeners (salt regenerated) for domestic use. Maximum working pressure 6.0 bar. Cold water use only.
Range of polyethylene pressure vessels with spun (blue) fibre glass casing. Maximum working pressure 10.0 bar. Maximum operating temperature 50°C.
‘Hostaform® C9021 ECO-B NATURAL, C9021, M15HP, C2521, C13021, C13031, C27021 ECO-B NATURAL, C27021, C52021 & M90JG’. Injection moulded, natural (which appear to be white) acetal materials available in the following colours: Black 14 DW (formerly known as Black 14), White 22, Grey 33, Grey 36, Grey 39, Red 46, Red 47, Yellow 56, Brown 65, Green 76, Blue 87, RAL 2010, RAL 4008 & RAL 5005. Customer specific colours may also be provided with a nomenclature following the structure ‘xx/yyyy DW’ where ‘yyyy’ denotes the specific colour shade, ‘DW’ denotes ‘Drinking Water’ & ‘xx’ denotes 10 – black, 20 - white (incl. Cream, 30 – grey, 40 – red (incl. Pink), 50 – yellow, 60 – brown (incl. Beige), 70 – Green & 80 – blue. For use with water up to 65°C.
'Deep High Build Liquid Bitumen Paint'. Factory applied, black coloured bitumen paint. Apply and cure as per manufacturer's instructions reference 'DI/BP/2021/011' dated April 15, 2021. For use with water up to 60°C.
'Sealcoat Black'. Black coloured, factory applied petroleum bituminous coating. Apply as per manufacturer's instructions for use reference 'PC 819' dated March, 26, 2021. Cure for 18 hours at 30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. Petroleum or asphaltic bitumen, NOT coal tar bitumen. Materials listed in this section are not approved for use for contact with water that is required to be wholesome on large water retaining structures such as lining of pipes, cisterns or water storage tanks.
'P658RC & CY10C washers'. P658RC is a black coloured, polyester resin impregnated carbon washer. CY10C is a dark grey coloured, phenolic resin impregnated carbon washer. For use with water up to 85°C.
'Unitech DIP Sulphate Cement'. Factory applied, grey coloured sulphate cement. Mix as per work instructions issue no. 'QAP-MOS-UNITECH 212-13- rev1', dated 21st December 2020. Cure for 6 hours@40°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JIZJ-2'. Factory applied, grey coloured Sulphate resistant Portland cement. Mix cement, sand & water in a 1:1.7:0.55 mass ratio. Cure for 5.5 hours@65°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'BGDI01 Sulphate Resistant Cement & BGDI02 Portland Cement'. Factory applied, grey coloured cements. Mix 1 part cement, 2 parts sand and 0.25 parts water. Cure for 10 hours@23°C. For use with water up to 65°C. These materials are only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'PMSP5065-M'. Factory applied, blue coloured Vitreous Enamel coating. Apply and cure as per user instructions reference 'PEM 37' dated '14/10/2020'. For use with water up to 85°C.
'Parasakti Sulphate Resisting Portland Cement'. Factory applied, grey coloured Sulphate Resistant cement mortar. Mix cement, sand and water in a 1: 1.5: 0.5 ratio. Cure for 28 days@5°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Rashmi Cement 43 Grade OPC'. Factory applied, grey coloured Ordinary Portland cement mortar. Mix cement, sand and water in a 1: 1.5: 0.5 ratio. Cure for 28 days@5°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'LSR Soft Touch Coating – Kohler NC001'. Factory applied, three-component, clear silicone coating. Mix coating, catalyst and thinner in a 100:2:500 mass ratio, stir for 10 minutes and then apply. Cure for 10 minutes@160°C, humidity 60%. For use with water up to 70°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘EUROKOTE® 46-20’. Factory applied, red-brown coloured, two-part epoxy resin coating. Mix and apply as per manufacturer's technical data sheet 'Doc. 087' dated 01/07/2011. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Kubotapowder TK1413F'. Factory applied, grey coloured epoxy resin coating. Apply as per manufacturer's instructions 'GR-294E' dated 2018/10/01. Cure for 20 minutes@180°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'WB-108'. Factory applied, two-component, grey coloured epoxy coating. Mix, apply and full cure (7 days@20°C) as per manufacturer's technical data sheet 'file no. TWJ-WB-108', 'edition: A1' dated 01/12/2020. For use with water up to 65°C.
'EPOXY TB BT Grey RAL 7016'. Factory applied, grey coloured, fusion bonded epoxy coating. Apply as per Technical Data Sheet 'document version:1' dated 'June 22, 2021'. Cure for 10 minutes@160°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Acrylatik'. Site applied, Acrylate primers available in white, red, blue and black colours. Apply as per manufacturer's instructions 'Appendix No. 1, TU 2316-002-92 872914-2016' dated '11.02.2016'. Cure for 20 minutes@20°C and then 20 minutes@90°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Superfast Potable Water (SFPW)'. Site applied, grey coloured (once mixed), two-component epoxy putty. Mix Part A (white coloured putty) with Part B (cream coloured putty) in a 1:1 mass ratio and apply as per manufacturer's instructions 'SOP Number RM1 version 1.0', dated '06/10/2022'. Cure for 24 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Solico Ivory GRP Panel'. Beige coloured, compression moulded GRP panel. For use with water up to 60°C.
'Extralite Pipe'. Light green/brown coloured GRP pipe manufactured by filament winding. For use with water up to 60°C.
'Extralite Fitting'. Brown coloured GRP fitting manufactured by hand lay-up. For use with water up to 60°C.
'ajpipe GRP Pipe'. Beige coloured GRP pipe manufactured by continuous filament winding. For use with water up to 23°C. From February 2024, the pipe is for use with water up to 60°C.
'JUSTLINK® JLPEX'. Single layered, off-white (translucent), extruded PEX hose. For use with water up to 60°C.
'Purolite® A600E/9149'. Yellow coloured ion exchange resin. For use with water up to 23°C.
'Purolite® A860S'. White coloured ion exchange resin. For use with water up to 23°C.
'FS Sill Tech Grease'. Off-white coloured (opaque) silicone grease. Apply as per manufacturer's instructions. For use with water up to 65°C.
'SAGITTA VP 763 Silicone Grease'. White coloured, opaque silicone grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
‘4TECH 9G22130 W-A ABK, 4TECH 9G22135 W-A ABK, 4TECH 9G22140 W-A ABK, 4TECH 9G22145 W-A ABK, 4TECH 9G22150 W-A ABK, 4TECH 9G22155 W-A ABK & 4TECH 9G22160 W-A ABK’. Black coloured, glass-fibre reinforced PA66 materials. For use with water up to 23°C.
‘4MID 9A22130 HW-A ABK, 4MID 9A22135 HW-A ABK, 4MID 9A22140 HW-A ABK, 4MID 9A22145 HW-A ABK & 4MID 9A22150 HW-A ABK’. Black coloured, glass-fibre reinforced PA66 materials. For use with water up to 23°C.
'Mapex® AN4920SN FWB50 & GITOP® G3A2 M01FWB'. Black coloured, injection moulded, glass fibre reinforced PA66 materials. For use with water up to 85°C.
'Grilon BG-30/2 natural (appears cream in colour) & Grilon BG-30/2 black 9697 (black coloured)'. Injection moulded PA-GF30 materials. Grilon BG-30/2 black 9697 is for use with water up to 85°C. Between 1st October 2020 and 10th May 2022, Grilon BG-30/2 natural was for use with water up to 23°C. Between 11th May 2022 and 31st October 2025 Grilon BG-30/2 natural is for use with water up to 60°C.
AKROMID® A3 GF 25 8 HU natural (8120) AKROMID® A3 GF 30 8 HU natural (8102) AKROMID® A3 GF 33 8 HU natural (8128) AKROMID® A3 GF 35 8 HU natural (8121) AKROMID® A3 GF 40 8 HU natural (8122) AKROMID® A3 GF 43 8 HU natural (8130) AKROMID® A3 GF 45 8 HU natural (8123) AKROMID® A3 GF 50 8 HU natural (8124) AKROMID® A3 GF 55 8 HU natural (8125) AKROMID® A3 GF 60 8 HU natural (8126) AKROMID® A3 GF 25 8 HU black (8118) AKROMID® A3 GF 30 8 HU black (8112) AKROMID® A3 GF 33 8 HU black (8129) AKROMID® A3 GF 35 8 HU black (8113) AKROMID® A3 GF 40 8 HU black (8114) AKROMID® A3 GF 43 8 HU black (8131) AKROMID® A3 GF 45 8 HU black (8115) AKROMID® A3 GF 50 8 HU black (8116) AKROMID® A3 GF 55 8 HU black (8119) AKROMID® A3 GF 60 8 HU black (8117) Natural (appears white) and black coloured, injection moulded, glass fibre reinforced PA66 materials. For use with water up to 85°C.
'POLYNT 1349 TAEQ20 to be used in conjunction with POLYCOR LP PA FC CLEAR 0200'. POLYNT 1349 TAEQ20 is a polyester resin and LP PA FC CLEAR 0200 is a factory applied, gel coat (when used together the material appears light pink in colour). Apply as per manufacturer's TDS ‘7206 updated 10.10.17’. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Dhara HDPE Black Pipe'. Black coloured (with blue outer stripes), extruded HDPE pipe. For use with water up to 65°C.
'Dhara MDPE Blue Pipe'. Blue coloured, extruded MDPE pipe. For use with water up to 65°C.
'LSPE-BE002 PE Pipe (Deep Blue)'. Blue coloured, extruded polyethylene pipe. For use with water up to 60°C.
Page 17 of 171
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
