Wall mounted, thermostatic shower valve (chromium plated brass body) incorporating a two-way diverter valve headwork that controls flow between each shower outlet with a cube type operating member. The temperature is controlled independently via a thermostatic cartridge with a cube type operating member with a manual override button. Both inlets incorporate a stainless-steel strainer and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure: 10.0 Bar. Maximum operating temperature: 85°C.
Range of wafer and fully lugged butterfly valves with a black or blue epoxy coated ductile iron body and either lever type or handwheel operating members. Maximum working pressure: 4925, 4925B, 4925G, 4923 & 4923G = 25.0 bar, 970W, 970WB, 970WG, 973W & 973WG = 16.0 bar. Maximum operating temperature 85°C.
Range of wafer and fully lugged butterfly valves with a black or blue epoxy coated ductile iron body and either lever type or handwheel operating members. Maximum working pressure: FM638, FM638B, FM639, DM638 & DM639 = 25.0 bar, F624, F624B, F625, DM925LW & DM925G = 16.0 bar. Maximum operating temperature 85°C.
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies, stainless steel (CF8M) discs and EPDM seats. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of lugged and wafer type butterfly valves with blue epoxy coated bodies, incorporating EPDM rubber ‘O’-rings and seat, and either a bronze (AB2), stainless steel (CF8 & CF8M) or blue epoxy coated or nickel plated, ductile iron (DI) disc. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of spring loaded, non-return valves with ductile iron bodies (blue epoxy powder coated) with stainless steel discs, springs and shafts and EPDM seat. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of tilting disc non-return valves with blue epoxy coated ductile iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of pilot operated pressure reducing control valves with blue or grey epoxy coated ductile steel bodies. Maximum supply pressure: 20.0 bar. The product is available with the following adjustable outlet pressures: between 1.0 and 7.0 bar or between 4.0 and 12.0 bar. Maximum operating temperature: 85°C.
Range of pre-set pressure relief valves with brass or DZR brass bodies and EPDM diaphragms. The valves are fitted with hand operated easing gear. Pre-set pressure 3.0 bar for all models. Maximum operating temperature 85°C.
Range of angled spherical valves incorporating a chrome plated brass body and ball with butterfly operating members. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Flow through valve (chromium plated brass) for connection to expansion vessels. The product incorporates an isolation valve and a drain valve. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with DZR brass bodies (chromium plated), chromium plated brass balls, PTFE seat and single lever operating members. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of gate valves with brass or DZR brass bodies, non-rising spindles and either hand wheel or lockshield operating members. The 4366 and 4363 compression models are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves, brass body and disc with a handwheel operating member. Maximum working pressure 20.0bar Maximum operating temperature 100°C
Range of gate valves with bronze bodies with metal seats. The valves operate via a non-rising spindle headworks that incorporate a wheel type operating member or lock shield type (see models). Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves with bronze bodies with metal seats. The valves operate via a non-rising spindle headworks that incorporate a wheel type operating member or lock shield type (see models). Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies, and an EPDM wedge, gasket and ‘O’-ring. The BT1405 & BT1406 models have a rising spindle, the BT1401 & BT1402 models have a non-rising spindle, both have a handwheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Angled servicing valves with chrome plated brass bodies incorporating dome type operating member. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of water conditioners with stainless steel bodies. AFL012 MFB has a matt black finish and AFL012MFC has a chrome plate finish. Models with compression connections are for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C.
'Polipom C Natural WR' and 'Polipom C Black WR'. Natural (appears white) and black coloured, injection moulded POM materials For use with water up to 85°C.
'HP204AD'. Grey coloured carbon bearing, pressed, sintered, impregnated with phenolic resin and rebaked. For use with water up to 85°C.
'Rubalit A 1896'. White coloured, dry-pressed ceramic disc. For use with water up to 85°C.
'JDFF-OPC-01'. Factory applied, grey coloured Ordinary Portland Cement. Mix cement, sand & water in a 1:2:0.50 weight ratio and apply as per manufacturers Work Instruction 'WI-Pc-01-5', 'Issue #: 5 Revision #: 1', dated '10.01.2025'. Cure for 48 hours@23°C. For use with water up to 85°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
EUROKOTE® 711.92BF bleu 5012, EUROKOTE® 711.92BF bleu 5015, EUROKOTE® 711.92BF bleu 5005 CR, EUROKOTE® 711.92BF bleu 5005 & EUROKOTE® 711.92BF bleu 5017. EUROKOTE® 711.92BF noir 9005. EUROKOTE® 711.92 bleu 5012, EUROKOTE® 711.92 bleu 5015, EUROKOTE® 711.92 bleu 5005, EUROKOTE® 711.92 bleu 5005 CR & EUROKOTE® 711.92 bleu 5017. EUROKOTE® 711.92 noir 9005. EUROKOTE® 711.92 BF Brun Rouge & 711.92 Brun Rouge Factory applied, blue, black or red coloured epoxy coatings. Apply as per manufacturer's technical data sheets dated 04/03/2025. Cure for 2 minutes@200°C. For use with water up to 85°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'AL 83275'. Factory applied, blue coloured enamel coating. Apply as per manufacturer's TDS 'TDS-2025-AL83275-REV00', dated '03.07.2025'. Cure for 7 minutes@860°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TESNIT® BA-KTW-G'. Off-white coloured NBR/fibre gasket material manufactured by calendaring. For use with water up to 85°C.
'EPP-GRE Pipe'. Translucent, green coloured GRE pipe (with epoxy resin), manufactured by filament winding. For use with water up to 85°C.
'Molykote® G-5511'. White coloured (opaque), silicone based grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
'ICMA PE-RT TYPE II/AL/PE-RT TYPE II Multilayer Pipe'. Extruded, multi-layered pipe comprising of a white coloured PE-RT TYPE II inner and outer layer and aluminium middle layer. For use with water up to 85°C.
'Salman Plastic IpekBoru HDPE Pipe'. Blue coloured, extruded HDPE pipe. For use with water up to 85°C.
'PE-UltraFLO Pipe'. Black coloured, extruded HDPE pipes. For use with water up to 85°C.
'Plastazote HD30 to HD110'. Extruded, HDPE foams available in natural (appears white) or black (appears dark grey). 'Evazote EV30 to EV50'. Extruded, EVA foams available in natural (appears white) or black (appears dark grey). 'Plastazote LD70’. Extruded, LDPE foams available in natural (appears white coloured) or black. For use with water up to 85°C. 'Plastazote LD15 to LD60’. Extruded, LDPE foams available in natural (appears white coloured) or black. For use with water up to 50°C.
'Plate PE 100 natur'. White coloured (translucent), extruded, polyethylene 'support' component. For use with water up to 85°C.
'Polypipe MecFlow Pipes'. Triple layered, extruded PPR pipe consisting of a white coloured inner, black coloured middle and grey coloured (with white stripe) outer layer. For use with water up to 85°C.
'Polypipe MecFlow Fittings'. Grey coloured, injection moulded PPR fittings. For use with water up to 85°C.
'Advance Plastics PPR Pipe'. Green coloured (with red stripe), extruded PPR pipe. For use with water up to 85°C.
'Locking Pin NGAB-00707'. Off-white coloured (translucent), extruded polypropylene pipe. For use with water up to 85°C.
‘RIALENE P 100 SGFxx KTW grau K 7-128, RIALENE P 100 SGFxx KTW weiß K 9-112, RIALENE P 100 SGFxx KTW schwarz’. Injection moulded polypropylene materials available in grey, white and black. The ‘xx’ in the material name can be replaced with any number between ‘10’ and ‘50’. For use with water up to 85°C.
‘JCP HIGH Load Vinylester JFV380SF & JFV300SF’. Site applied, grey coloured, two-part (resin & hardener is automatically mixed in a 10:1 volume ratio through dispensing nozzle) anchor resin. Apply and cure as per ’T Load’ cures set out in Table B3 of European Technical Assessment ‘ETA 15/0704’, dated ‘31/01/2023’. For use with water up to 23°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B3 of European Technical Assessment ‘ETA 15/0704’ then the material is not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
'B8066'. Black coloured, compression moulded Chlorobutyl rubber material. Shore hardness 50. Tested in-radius size 1.05mm. For use with water up to 85°C.
'3W10-70-IR'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 1.75mm. For use with water up to 85°C.
'NER EPDM - 80'. Black coloured, compression moulded EPDM material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 50°C.
'HC-EP7001165PWRC'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'CSTD/BS6920-BA60' (shore hardness 60), 'CSTD/BS6920-BA70' (shore hardness 70) and 'CSTD/BS6920-BA75' (shore hardness 75). Black coloured, compression moulded EPDM materials. Tested in-radius size 1.05mm. For use with water up to 85°C.
'07148-60'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘ELASTOSIL® R’ solid silicone rubber materials. The number in brackets indicates shore hardness. Tested in-radius size 1.0mm. The following grades are natural and are for use with water up to 85°C. E indicates ELASTOSIL® AUX Crosslinker E. C1 indicates ELASTOSIL® AUX Crosslinker C1. Grades for extrusion and press moulding: R 401/20 E (shore hardness 20), R 401/30 E (30), R 401/40 E (40), R 401/50 E (50), R 401/55 E (55), R 401/60 E (60), R 401/70 E (70), R 401/80 E (80) & R 401/90 E (90). R 402/60 E (shore hardness 60), R 401/65 E (65) & R 401/75 E (75). R 420/30 E (shore hardness 30), R 420/40 E (40), R 420/50 E (50), R 420/60 E (60) & R 420/70 E (70). Grades for press moulding: R 401/20 C1 (shore hardness 20), R 401/30 C1 (30), R 401/40 C1 (40), R 401/50 C1 (50), R 401/55 C1 (55), R 401/60 C1 (60), R 401/70 C1 (70), R 401/80 C1 (80) & R 401/90 C1 (90). R 402/60 C1 (shore hardness 60) & R 402/75 C1 (75). R 420/30 C1 (shore hardness 30), R 420/40 C1 (40), R 420/50 C1 (50), R 420/60 C1 (60) & R 420/70 C1 (70). R 420/30 C1 & R 420/70 C1. The products may be coloured using the following ELASTOSIL® pigment pastes, also for use with water up to 85°C: PT Yellow RAL 1021. PT Yellow RAL 1016. PT Red RAL 3000 F. PT Red brown RAL 3013. PT Light brown RAL 8003. PT Dark brown RAL 8015. PT Green RAL 6017. PT Ultramarineblue RAL 5002. PT Light blue RAL 5015. PT Grey RAL 7040. PT Deep black RAL 9005. PT Black RAL 9017. PT White RAL 9010.
ELASTOSIL® LR liquid silicone rubber materials. The number in brackets indicates shore hardness. Tested in-radius size 0.8mm. The following grades are natural (appear white, opaque) and are for use with water up to 85°C. Grades for injection moulding: LR 3003/10 TR A+B & ELASTOSIL LR 3003/20 TR A+B. LR 3071/40-60 A & B (40 - 60). LR 3003/30-80 A & B (30 - 80). LR 3004/20-70 A & B (20 - 70). The products may be coloured using the following ELASTOSIL® pigment pastes, also for use with water up to 85°C: FL yellow RAL 1016. FL orange RAL 2004. FL Red Brown RAL 3013. FL dark blue RAL 5010 & FL light blue RAL 5015. FL grey RAL 7000. FL carbon black RAL 9005. FL black RAL 9011. FL white RAL 9010. FL Red RAL 3000 F. FL Orange 2004 F. FL Light Blue 5015 F. FL Black 9005 F. FL green RAL 6010. ELASTOSIL® R plus platinum catalysed HTV silicone rubber. The number in brackets indicates shore hardness. Tested in-radius size 0.8mm. The following grades are natural and are for use with water up to 85°C. Grades for injection and press moulding: R plus 4001/40-80 (40 - 80). Grades for extrusion: R plus 4305/40-80 (40 - 80). The products may be coloured using the following ELASTOSIL® pigment pastes, also for use with water up to 85°C: PT yellow RAL 1016. PT orange RAL 2004. PT dark blue RAL 5010 & PT light blue RAL 5015. PT carbon black RAL 9005. PT white RAL 9010.
'Loxeal 85-86'. Green coloured anaerobic adhesive. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions
'Drei Bond 5330'. Green coloured anaerobic adhesive. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions
'Bondrite A2577'. Anaerobic adhesive which is available in a yellow colour or in a yellow/orange colour. Apply as per manufacturer's instructions and cure for 15 minutes@25°C or 24 hours@22°C. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions.
Page 147 of 158
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
