Range of drain taps with brass or DZR brass body (some models chrome plated) and rising spindle headwork. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of wall mounted hose untion taps with chrome plated brass body and spindle headwork with dome type operating member. Maximum operating pressure 10.0 bar. Cold water use only.
Range of nylon or stainless steel braided flexible hose assemblies incorporating a PE-X inner hose, EPDM ‘O’-rings and/or gaskets. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of PVC lined shower hoses with silicone rubber gaskets and interlocked chromium plated outer coating. For open outlet use only. Maximum operating temperature 65°C.
Range of nylon braided (DG50X model series) or stainless steel braided (DG10X model series), PEX lined flexible hose assemblies with a variety of end connections (see models for full breakdown), including EPDM washers and ‘O’-rings where applicable. Some models are supplied with screwdriver operated isolation valves (see model list). All compression and push-fit fittings are to be used with copper pipe (manufactured to EN 1057). Maximum working pressure: 16 bar. Maximum operating temperature: 85°C.
Range of nylon braided (DG50E model series) or stainless steel braided (DG10E model series), EPDM lined flexible hose assemblies with a variety of end connections (see models for full breakdown), including EPDM washers and ‘O’-rings where applicable. Some models are supplied with screwdriver operated isolation valves (see model list). All compression and push-fit fittings are to be used with copper pipe (manufactured to BS EN 1057). Maximum working pressure: 16 bar. Maximum operating temperature: 85°C.
Range of indirect and direct unvented storage cylinders. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 7.0 bar @ 90˚C. The product is supplied with an inlet control group (safety kit) consisting of a pressure reducing valve pre-set at 3.0 bar, strainer, an expansion relief valve set at 6.0 bar and an approved check valve cartridge (verified by test - suitable for backflow protection against Fluid Category 2). A tundish and expansion vessel are also provided. Maximum working pressures: Primary: 3.0 Bar Secondary: 5.5 Bar Solar: 3.0 bar Maximum operating temperature 90.0°C
Range of cased and insulated stainless steel unvented water storage heaters. The DHW circuit includes a factory fitted combined temperature and pressure relief valve set at 6.0 bar and 90˚C. The product can be supplied with two possible safety kits (inlet control groups). One includes a pressure reducing valve adjustable between 1.5-6.0 bar, (but set at 3.0 bar), a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2) and a pressure relief valve pre-set at 4.5 bar. The other includes a pressure reducing valve pre-set at 3.0 bar, an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection, and a pressure relief valve pre-set at 4.5 bar. The product is also supplied with an expansion vessel and a tundish. The compression connection of each inlet control group is for use with the following pipes: Both for use with copper pipe (manufactured to BS EN 1057). The inlet control group without an adjustable pressure reducing valve can also be used with PB pipe (with inserts) (manufactured to BS EN 7291-2:2010) and PEX pipe (with inserts) (manufactured to BS EN 7291-3:2010). Maximum supply pressure to inlet control group pressure reducing valve: 16.0 bar. Maximum working pressure 4.0 bar. Maximum operating temperature 99°C. Cold supply only.
Range of wall mounted, concealed, bath-shower mixer valves (brass bodies, chromium plated trim sets) incorporating a ceramic cartridge headwork with single lever operating members and a manual diverter to two outlets. Maximum working pressure 10 bar. Maximum operating temperature 60°C
Wall mounted, manually operated blending shower valve with (brass bodies - various finishes) incorporating a ceramic cartridge headwork and a single lever operating member. The shower outlet connection incorporates an approved single check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar. Maximum operating temperature 70.0°C
Wall mounted, thermostatic shower valve, (brass body – chrome plated), incorporating a single sequential headwork with a single lever operating member. The inlet elbows incorporate key operated spherical valves with chrome plated brass balls, PTFE seats and approved single check vlave cartridges, however, the complete product has not been fully tested to demonstrate backflow protection. To be used with copper pipe only – Standard EN 1057 Maximum working pressure 5 Bar. Maximum operating temperature 65°C
Range of wall mounted, exposed, thermostatic shower valves (chromium plated brass) incorporating a single sequential headwork controlling both flow and temperature with a single lever operating member. The products are supplied with 15mm compression inlet elbows incorporating approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The inlets also incorporate plastic flow regulators. The 90033CP model can have either a top or bottom outlet, which is achieved by re-positioning the blanking plug and threaded outlet. The compression connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of concealed, wall mounted thermostatic blending valves with brass bodies (chromium plated trim set). The product incorporates a ¼ turn ceramic disc or a 2 way manual diverter with shut-off position to control the flow, with dome type operating members.The temperature is controlled independently via thermostatic cartridges, with dome type operating members. The inlets incorporate approved check valve cartridges, however, the complete products have not been fully tested to demonstrate they provide backflow protection. Maximum working pressure: 5 Bar. Maximum operating temperature: 60°C.
Range of wafer, lug type and double flanged butterfly valves incorporating blue epoxy coated ductile iron bodies, either stainless steel (CF8 or CF8M) or blue epoxy coated ductile iron discs and an EPDM seat. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Wall mounted concealed shut off valve with brass body incorporating a non-rising spindle headwork. Maximum working pressure 10.0 Bar Maximum operating temperature 80.0°C
Range of in-line, adjustable, pressure reducing valves with DZR brass bodies and incorporating a stainless steel strainer. Maximum supply pressure 16.0 bar. Outlet pressure range 1.0 to 6.0 bar with an inlet pressure of up to 10 bar Outlet pressure range 2.0 to 6.0 bar with an inlet pressure above 10 bar Maximum operating temperature 60°C.
Range of angle valves (brass bodies – various finishes), incorporating non-rising spindle headworks with a dome type operating members and NBR O-rings and PTFE Seals. Maximum working pressure 10 bar. Maximum operating temperature – Cold Water Use
Range of spherical valves with nickel plated brass bodies, chromium plated brass balls and various operating members (see models). Products incorporate EPDM O-rings and PTFE seats. Maximum working pressure ½” – 1” 30 bar, 1 ¼” – 2” 25 bar. Maximum operating temperature 100°C.
Range of lever operated spherical valves with brass bodies (chromium plated), incorporating chromium plated balls and PTFE seats. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with stainless steel bodies, chrome plated brass ball and PTFE seats. Maximum working pressure 68.9Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Page 146 of 201
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
