Range of combined thermal balancing and pressure reducing valves with gun metal bodies, stainless-steel strainer, pressure gauge and temperature gauge. Maximum inlet supply pressure 16.0 bar. Outlet pressure range of 1.5 bar – 5.5 bar. Maximum operating temperature 85°C.
Range of in-line adjustable pressure reducing valves with Nickel plated DZR brass bodies and EPDM gaskets. Maximum inlet supply pressure 16.0 bar. Outlet pressure in the range of 0.5 bar to 6.0 bar. Maximum operating temperature 80°C.
Range of in-line adjustable pressure reducing valves, with DZR brass bodies and EPDM seat washers & ‘o’ rings and stainless-steel filters. Various models supplied with pressure gauge (please see model list). Maximum inlet supply pressure 16.0 bar. Outlet pressure range: 0.8-6.0 bar. Maximum operating temperature 80°C.
Range of latching solenoid valves with brass bodies and EPDM diaphragm Maximum working pressure 13.0 bar. Maximum operating temperature 55°C.
A range of normally closed servo-assisted diaphragm solenoid valves with brass bodies and EDPM diaphragms. Models 23C, 23D, 23E & 23F have a maximum working pressure of 16.0 bar. Models 23G, 23H & 23I have a maximum working pressure of 10.0 bar. Cold water use only
Solenoid valves with a plastic body and silicone diaphragm and ‘O’ rings. Maximum working pressure 8.0 bar. Cold water use only.
Range of normally closed solenoid valves with a plastic body and silicone rubber diaphragm & ‘O’-rings. Models ending ‘007’ have a maximum working pressure of 0.25 bar. All other models have a maximum working pressure of 0.06 bar. Maximum operating temperature 90°C.
Range of bistable (all models) or monostable/normally closed (19.00x.287 only) solenoid valves with either a plastic body (19.00X.287) or plastic internal body with stainless steel threaded casing (50.005.102 and 50.005.(050) models) with EPDM diaphragms and ‘O’-rings. Maximum working pressures: 50.005.(050) model: 8.0 bar. All other models: 10.0 bar. Maximum operating temperature 70°C
Range of spherical valves incorporating DZR brass bodies and balls (nickel plated), EPDM ‘O’-rings, PTFE seats and red or blue coloured lever type operating members. Maximum working pressure 16.0 bar for compression models Maximum working pressure 40.0 bar for 1¼”-2” RP Female & pressfit models Maximum working pressure 50.0 bar ½”-1” RP Female & pressfit models. Maximum operating temperature 85°C.
Range of spherical valves incorporating brass bodies and balls (chrome plated), EPDM ‘O’-rings and PTFE seats. Model 124-3200 has a maximum working pressure 50.0 bar. Models 124- 3201 and 124-3202 have a maximum working pressure 40.0 bar. Model 124-3203 has a maximum working pressure 25.0 bar. Models 124-3204 and 124-3205 have a maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Spherical valve incorporating a brass body (brushed chrome), chrome plated brass ball, ‘y’-patterned strainer, PTFE seats and single lever operating member. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of PVC-U double union ball valves incorporating EPDM O-rings. Maximum working pressure 16.0 bar. (Cold water use only).
Angled stop valve with a chrome plated brass body and NBR ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of commercial front loading dishwashing machines with flow controlled by solenoid and discharged via type AA air gap arrangement. The products are supplied with a grey coloured PVC supply hose. Maximum working pressure 4.0 bar. Cold water supply only.
'Toyolac 700-314'. Beige coloured, injection moulded ABS material. For use with water up to 23°C.
'Dicoat Medium Temp Black'. Factory applied, black coloured bitumen coating. Apply as per manufacturer's user instructions reference 'SPL/RD/UI/2019100121', issue no. '01' dated 08.07.2020. Cure for 7 days@30°C. Between 1st January 2021 to 22nd November 2021, the material is for use with water up to 50°C. Between 23rd November 2021 and 31st January 2026, the material is for use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'D-1375-077'. Grey coloured, resin impregnated carbon graphite washers manufactured by isotactic pressing, sintering and grinding. For use with water up to 85°C.
'H-3500-6351-9221'. Grey coloured silicon carbide washers manufactured by isotactic pressing, sintering and grinding. For use with water up to 85°C.
'Tianli 5070 Polyester Epoxy Powder Coating'. Blue coloured, factory applied polyester epoxy powder coating. Apply as per manufacturer's Technical Data Sheet 'V.131130' dated 2013-11-30. Cure for 20 minutes@180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'V-PET#1600 GRAY AG'. Factory applied, grey coloured epoxy powder paint. Apply as per manufacturer's instructions ref '20210201-1' dated 2021/2/1. Cure for 10 minutes@200°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'High Build Solvent Free Epoxy Coating Red'. Factory applied, red coloured epoxy coating. Apply as per manufacturer's user instructions reference 'SPL/RD/UI/202006119', issue no, '01' dated 20.08.2020. Cure for 24 hours@30°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JIZJ-1'. Factory applied, light grey coloured Portland cement mortar. Mix cement, sand and water in a ratio of 1:1.7:0.55. Cure for 5 hours and 30 minutes@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'HSXX CM-1'. Factory applied, grey coloured cement mortar. Mix, apply and cure as per manufacturer's Technical Data Sheet issue number '001' dated '2020.08.01'. For use with water up to 65°C.
'KOPATCH PC300-D/BLUE'. Factory applied, two component, dark blue coloured epoxy resin coating. Mix parts A & B in a volume ratio of 2:1. Cure for 7 days@20°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotaguard VA 5001. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's TDS dated '9 November 2015'. Cure for 210 seconds@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SRC RZ S&M&BDN 20'. Factory applied, grey coloured sulphate resistant cement mortar. Mix cement and sand in a 1:2.2 mass ratio. Combine that mix and water in a 1:0.45 mass ratio. Cure for 24 hours@25°C and 95% relative humidity. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EP01'. Factory applied, blue coloured epoxy powder coating. Apply and cure as per manufacturer's instructions 'V6.3' issued March 2019. For use with water up to 65°C.
'V-PET #1600 Gray F'. Factory applied, grey coloured epoxy resin powder coating. Apply as per manufacturer`s instructions ref. no. '20210216-1' dated 2021/2/16. Cure for 10 minutes@200°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Vastcoat MT'. Factory applied, blue coloured thermoplastic powder coating. Apply as per manufacturer's instructions 'Issue number 02000202710' dated 20.02.2020. Cure for 10 minutes@200°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TBX 500'. Triple layered, extruded hose comprising of a white coloured, translucent TPE inner layer, black coloured PVC middle layer and grey coloured PVC outer layer. For use with water up to 23°C.
'IKV Tribostar SSI 1203TF/IKV Tribofood SSI 1203TF'. Translucent, white coloured silicone greases. Apply as per manufacturer's instructions. For use with water up to 85°C.
'Grasso L. 100 Lubricating Grease'. White coloured grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
‘Tecomid NA40 GR30 BK005 HS QW, Tecomid NA40 GR35 BK005 HS QW, Tecomid NA40 GR40 BK005 HS QW, Tecomid NA40 GR45 BK005 HS QW & Tecomid NA40 GR50 BK005 HS QW’. Black coloured, glass-fibre reinforced PA66 materials. For use with water up to 23°C.
'Celanyl A3 WR GF30 BK 9005/Z/FA'. Black coloured, injection moulded PA material. For use with water up to 85°C.
'Badamid B70 GF40 UV WL Black'. Black coloured, injection moulded, glass filled PA6 material. For use with water up to 65°C.
‘ELGEF PE-100 electrofusion fittings’, Black coloured, injection moulded polyethylene electrofusion fittings. For use with water up to 65°C.
'MMP PE100 Pipe'. Black coloured (with blue coloured external stripes), extruded PE100 pipes manufactured from 'Sabic P6006' or 'Borouge HE3490-LS'. For use with water up to 85°C.
'Popular HDPE Pipe'. Black coloured (blue external stripes), extruded HDPE pipe. For use with water up to 60°C.
'Lasertec Multilayer Compound Pipes (White)'. Extruded PE-RT/Al/PE-RT pipe comprising of a black coloured, PE-RT Type 2 inner layer, aluminium outer layer and white coloured PE-RT outer layer. For use with water up to 70°C.
'TP10847 Prisma Black'. Black coloured polyethylene material manufacture by rotational moulding. For use with water up to 70°C.
'HE3490-ELS-H'. Black coloured, extruded polyethylene material. For use with water up to 60°C.
`Revolve N-525 (6056) Natural (appears white coloured) & BH3239 Black (black coloured)`. Polyethylene materials manufactured by rotational moulding. For use with water up to 85°C.
`Revolve N-650/6068 Natural (appears cream coloured) & M-668 Black (black coloured)`. Polyethylene materials manufactured by rotational moulding. For use with water up to 85°C.
'Revolve 6405U Natural (appears white coloured) & Revolve M-1585 Black (black coloured)'. Polyethylene materials manufactured by rotational moulding. For use with water up to 85°C.
‘Revolve N-840 (HD3850) & Revolve M-750 DR Black’. Revolve N-840 (HD3850) is a white coloured polyethylene material & Revolve M-750 DR Black is a black coloured polyethylene material. Both are manufactured by rotational moulding. For use with water up to 85°C. Please note that ‘Revolve N-840 (HD3850)’ was formerly known as ‘Revolve N-840 (6850)’.
'Revolve N-307 Boat Blue M2-018D'. Blue coloured polyethylene material manufactured by rotational moulding. For use with water up to 85°C.
‘Tecomid HT NT40 GR30 BK009 01 QW, Tecomid HT NT40 GR35 BK009 01 QW, Tecomid HT NT40 GR40 BK009 01 QW, Tecomid HT NT40 GR45 BK009 01 QW, Tecomid HT NT40 GR50 BK009 01 QW, Tecomid HT NT40 GR55 BK009 01 QW & Tecomid HT NT40 GR60 BK009 01 QW’. Black coloured, injection moulded glass-fibre reinforced PPA materials. For use with water up to 85°C.
'DACTAtherm PP-R 80 Green Pipe'. Green coloured, extruded polypropylene pipe. For use with water up to 85°C.
'Popular PPRC 100 Pipe'. Green coloured, extruded PPR pipe. For use with water up to 60°C.
'Hostalen PP H5416T'. White coloured (translucent), extruded polypropylene material. For use with water up to 60°C.
Page 15 of 234
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
