'JAZLINE DW'. Factory applied, two-component, light green coloured epoxy coating. Mix in a 3:1 volume ratio and apply as per manufacturer's TDS issued '1 / 2022'. Cure for 7 days@28°C. For use with water up to 60°C.
'P • HSR42.5'. Factory applied, grey coloured Sulphate resistant Portland cement. Mix cement:medium sand:water in 1:1.4:0.45 weight ratio and apply as per manufacturer's instructions 'Version 03', dated '29th-07-2024'. Cure for 3 hours at 25°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Enviroline 2405'. Site applied, off-white coloured (once mixed and applied), two-component epoxy. Mix parts A (light grey, opaque liquid) and B (white, opaque liquid) in a volume ratio of 2:1 and apply as per manufacturer's TDS 'Ref:10139', 'Issue Date:8/21/2017'. Cure for 7 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ELS 108 & ELS 101'. Extruded, multi-layered hoses comprising of a black coloured PVC inner layer, white coloured polyester middle layer and grey coloured PVC outer layer. For use with water up to 23°C.
'T100M'. White coloured (translucent) grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
'TP-A25-PA12'. Dark grey coloured, injection moulded, PA12 bonded strontium ferrite magnet. For use with water up to 50°C.
'DZT PANT I1000-NC; DZT PANT I10G05-NC; DZT PANT I10G10-NC; DZT PANT I10G15-NC; DZT PANT I10G20-NC; DZT PANT I10G25-NC; DZT PANT I10G30-NC; DZT PANT I10G35-NC; DZT PANT I10G40-NC; DZT PANT I10G45-NC; DZT PANT I10G50-NC; DZT PANT I10G55-NC; DZT PANT I10G60-NC; DZT PANT I10G65-NC (un-pigmented - appears beige)’. ‘DZT PANT I10G05-BK; DZT PANT I10G10-BK; DZT PANT I10G15-BK;DZT PANT I10G20-BK;DZT PANT I10G25-BK; DZT PANT I10G30-BK; DZT PANT I10G35-BK;DZT PANT I10G40-BK;DZT PANT I10G45-BK; DZT PANT I10G50-BK; DZT PANT I10G55-BK; DZT PANT I10G60-BK; DZT PANT I10G65-BK (black coloured)'. Injection moulded PA materials. For use with water up to 85°C.
'ForTii Ace WX51-FC NA99001'. Natural (appears beige in colour), injection moulded Polyamide material. For use with water up to 85°C.
'Durethan BKV15F 901510 DUS018'. Black coloured, injection moulded PA6 GF 15 material. For use with water up to 85°C.
'Aquapipe'. Black coloured, extruded HDPE (PE100) pipe. For use with water up to 23°C.
'GPS CRP100 Black Pipe'. Black coloured, extruded PE100 pipe. For use with water up to 23°C.
'JXPE100'. Black coloured, extruded HDPE pipe. For use with water up to 65°C.
'GUR® 4012, GUR® 4012 ECO-B, GUR® 2105, GUR® 2105 ECO-B, GUR® 2122, GUR® 2122 ECO-B, GUR® 2126, GUR® 2126 ECO-B, GUR® 4017, GUR® 4017 ECO-B GUR® 4018, GUR® 4018 ECO-B, GUR® 4120, GUR® 4120 ECO-B, GUR® 4150, GUR® 4150 ECO-B, GHR® 8020 & GHR® 8020 ECO-B’. Natural (material appears white/cream coloured, opaque) compression moulded UHMW-PE materials. ‘GUR® 2105, 2105 ECO-B, 2122, 2122 ECO-B. 2126, 2126 ECO-B’ are for use with water up to 60°C. ‘GUR® 4017, 4017 ECO-B, 4018, 4018 ECO-B 4012, 4012 ECO-B, 4120, 4120 ECO-B, 4150, 4150 ECO-B, GHR® 8020 & 8020 ECO-B' are for use with water up to 85°C.
'Aqua PE-1'. Black coloured, extruded PE material. For use with water up to 23°C.
'Poliext PP Compression Fittings PN16'. Black coloured, injection moulded, PP compression fittings. For use with water up to 23°C.
'Ultrason® S2010 G4 Schwarz 15038'. Black coloured, injection moulded polysulphone material. For use with water up to 85°C.
'Ball Nest (PTFE Teflon p/n FR 101-1)'. White coloured (opaque), compression moulded PTFE component. For use with water up to 85°C.
'Tuftane TFL-1HA'. Clear, blown TPU film. For use with water up to 23°C.
'70 EP 101p'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size 1.5mm. For use with water up to 85°C.
'EP60/1 BLK 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 60. Tested in-radius size 1.77mm. For use with water up to 85°C.
'51M7531 Diaphragm'. Black coloured, calendered, EPDM diaphragm. Shore hardness 75. Tested in-radius size 0.5mm. For use with water up to 85°C.
'560AL Water Seal'. Black coloured, injection moulded EPDM seal. Shore hardness 70. Tested in-radius size 2.12mm. For use with water up to 23°C.
'ERA10-2 SEALING'. Black coloured, compression moulded EPDM material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EP80R-01'. Black coloured, compression moulded EPDM rubber material. Shore hardness 80. Tested in-radius size 1.5mm. For use with water up to 50°C.
'EPWL-60'. Black coloured, injection moulded EPDM material. Shore hardness 60. Tested in-radius size between 1.25mm & 5.25mm. For use with water up to 23°C.
'ME0940/40 - 90'. Black coloured, injection moulded EPDM rubber material. Shore hardness between 40 & 90. Tested in-radii sizes between 1.0mm & 3.0mm. For use with water up to 85°C.
'OLD ETP890 70N'. Black coloured, injection moulded EPDM rubber. Shore hardness 70. Tested in-radius size 1.11mm. For use with water up to 85°C.
'EPWL-70'. Black coloured, injection moulded EPDM material. Shore hardness 70. Tested in-radius size between 1.25mm & 5.25mm. For use with water up to 23°C.
'3E60B11P & 3E70B03P'. Black coloured, compression moulded EPDM materials. Shore hardness 60 & 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'13K0705 NOK 'O' ring'. Red/brown coloured, compression moulded FKM rubber 'O' ring. Shore hardness 70. Tested in-radius size 1.24mm. For use with water up to 75°C.
'SU26F415H01 'O' ring'. Black coloured, compression moulded FKM rubber 'O' ring. Shore hardness 80. Tested in-radius size 0.9mm. For use with water up to 75°C.
'V8 Fluorocarbon Rubber Bellows'. Black coloured, injection moulded fluorocarbon rubber bellows. Shore hardness 70. Tested in-radii sizes between 0.7mm & 4.1mm. For use with water up to 85°C.
'Silicone Rubber Washer SIL40 (SIL4001)'. Black coloured, vulcanised silicone rubber washer. Shore hardness 40. Tested in-radius size 0.56mm. For use with water up to 85°C.
'Type 1 O-ring, T056D 124H16 Model Code P16'. Cream coloured (opaque), compression moulded silicone rubber 'O' ring. Shore hardness 70. Tested in-radius size 1.2mm. For use with water up to 85°C.
'Tangit Rapid'. Straw coloured adhesive intended to join pipe and fittings. Apply as per manufacturer’s instructions ‘TFU_TM_GB_0915’. Cure for 24 hours@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Fosroc Nitoseal SC600'. Site applied, grey coloured silicone sealant waterstop. Apply as per manufacturer's TDS issue '1.0', dated October 2024. Cure for 21 days at 7°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. These materials are for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992-3:2006 (Design of concrete structures – Liquid retraining and containing structures) with respect to normal frequency of joints. The material has been tested at a reduced surface area to volume ratio of 1000mm² per litre.
'Loctite 5800'. Red coloured anaerobic adhesive. Apply as per manufacturer's technical data sheet dated April 2012. For use with water up to 85°C. These products are to be applied and cured in strict accordance with the manufacturer's instructions
Range of wall mounted, two-hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve activated via infra-red sensor. Temperature is controlled independently via a thermostatic cartridge with a dome operating member which incorporates a manual override button. The spout outlets incorporate plastic aerators, and both inlets incorporate an approved single check valve cartridge (however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection) and stainless-steel strainers. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The main body incorporates a plastic flow regulator and stainless steel strainer prior to the solenoid. The inlets to the main body of the GS10, CM10 & GH10 model variants incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. These models also have a manual temperature control operated by a single lever on the side of the body. The inlet hoses incorporate a TPE gasket. The models are supplied with or without a pop-up waste. The GS20 & GM20 model variants are single feed. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The inlets to the main body of the M10, GC10, MX10, A10 & L10 model variants incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection, these models also have a manual temperature control operated by a single lever on the side of the body. The inlet hoses incorporate a stainless steel strainer (M10, GC10, MX10, A10 & L10 model variants) or combined TPE washer and stainless strainer (M20, GC20, A20 & L20 model variants). The models are supplied with or without a pop-up waste. The M20, GC20 A20 & L20 model variants are single feed. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Concealed BS EN 14055: 2018 WC flushing cistern incorporating a side or bottom entry compact type float operated inlet valve providing a Type AG air gap with a dual or single flush pneumatic drop valve capable of full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern can be operated by touch free electronic or manual push button / push plate options. Maximum working pressure 10.0 bar. Cold water use only.
Non-verifiable double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body. Maximum working pressure 16 Bar Maximum operating temperature 65°C
Non-verifiable double check valve assemblies incorporating two spring loaded resilient trim in-line check valve cartridges, DZR brass bodies (brushed chrome) and a drain port located in between the cartridges. The assemblies incorporate spherical valve. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Non-Verifiable double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a nickel plated DZR brass body. The assembly incorporates an isolation valve. Maximum working pressure 10.0 bar. Maximum operating temperature 85ºC.
Range of ceramic cartridge headworks with plastic bodies. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Range of ceramic disc headworks with brass bodies. For insertion into specifically dimensioned bores. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Ceramic cartridge headworks with a plastic body, incorporating silicone seals. The product is intended for insertion into specifically dimensioned tap assemblies. Maximum working pressure - 10 Bar Maximum operating temperature - 85 °C
Range of non-rising spindle headworks with a brass body and EPDM ‘O’-rings. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of push to open, push to close ‘detent’ headworks with plastic bodies and EPDM ‘O’-rings. For insertion into specifically dimensioned bores. Maximum working pressure: 10.0 Bar. Maximum operating temperature: 85.0°C.
Page 139 of 209
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
