Range of regulating and shut-off valves with brass bodies and EPDM ‘O’-Rings. Maximum working pressure 16.0 Bar for BSP (M) and 25.0 bar for BSP (F). Maximum operating temperature 85.0°C
Range of swing gate, non-return valves with (blue or red epoxy powder coated) ductile iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of double swing gate, wafer, non-return valves with blue epoxy coated ductile iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of swing gate, non-return valves with (blue or red epoxy powder coated) ductile iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spring loaded, non-return valves with ductile iron bodies (blue epoxy powder coated) with stainless steel discs, springs and shafts and EPDM seat. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of wafer or globe type spring loaded, resilient trim, non-return valves with cast iron bodies (blue epoxy powder coated). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of adjustable, in-line pressure reducing valves with DZR brass bodies, incorporating a spring loaded EPDM diaphragm and a gauge port. The products incorporate an integral stainless steel strainer. The outlet pressure range is adjustable between 1.0 and 6.0 bar. Maximum inlet supply pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 40°C
Range of adjustable, in-line pressure reducing valves with blue epoxy coated, cast iron bodies. SP models: maximum supply pressure 25.0 bar, outlet pressure range 1.5 to 7.0 bar. HP models: maximum supply pressure 25.0 bar, outlet pressure range 3.0 to 12.0 bar. LP models: maximum supply pressure 8.0 bar, outlet pressure range 0.5 to 3.0 bar. Maximum operating temperature 60°C.
Range of pilot operated pressure reducing valves with blue epoxy coated ductile iron bodies. The valves have an adjustable pressure reducing facility controlled via a pilot valve (with an operating range of 1 to 6 bar), with auxiliary components including stainless steel tubing, fittings and spherical valves. Maximum working pressure 16.0 bar. Maximum operating temperature 23°C.
Range of lever or butterfly operated spherical valves with brushed chromium plated brass bodies, chromium plated brass ball and PTFE seat. Maximum working pressure model K656: ¼” to ½” = 64.0 bar, ¾” to 1¼” = 50.0 bar, 1½” to 2” = 40.0 bar, 2½” to 4” = 25.0 bar. Model K6566 model: ¼” to ⅜” = 64.0 bar, ¾” to 1¼” = 50.0 bar, 1½” to 2” = 40.0 bar, 2½” to 4” = 25.0 bar. Models K8912 , K8913 & K6568 models: ¼” to ⅜” = 64.0 bar. Maximum operating temperature 99°C.
Range of spherical valves with either brass (UW24905 & UW24907 models) or nickel plated (UW24809, UW24906, UW24933, UW24908 & UW24934 models) brass bodies with chrome plated brass ball and operated via lever, butterfly type handle or screwdriver slot. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves incorporating nickel plated brass bodies with chrome plated brass ball and operated via lever, butterfly type handle or screwdriver slot. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with PVC bodies and ball. Maximum working pressure 16.0 bar. Cold water use only.
Range of brass spherical valves, incorporating chrome plated brass balls, butterfly type operating members and a drain off spigot connection that incorporates a rising spindle type headwork. For above ground use only. Maximum operating pressure 16 bar. Maximum operating temperature 85°C
Range of lever operated spherical valves with brass bodies, incorporating a chrome plated brass ball. Model 7741345 incorporates a drain valve end connection. For use with copper pipe to EN1057. Maximum working pressure 10 bar. Maximum operating temperature 85°C
Range of flanged ductile iron, blue epoxy coated gate valves with EPDM seats and hand wheel operating members. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of hand wheel operated or key operated gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM. Models HY-002A & HY-002B incorporate brass valve seats Maximum working pressure 16.0 Bar Maximum operating temperature 65.0°C
Range of flanged ductile iron, blue epoxy coated gate valves with EPDM seats and hand wheel operating members. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies and ductile iron wedges encapsulated in EPDM. The valve is operated via a non-rising spindle. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies, and an EPDM wedge, gasket and ‘O’-ring. The 166 30 SERIES model has a rising spindle, the 166 33 SERIES model has a non-rising spindle, both have a handwheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of screw down stop valves with brass bodies, EPDM gaskets and PTFE washers. For use with copper pipe to EN 1057. Maximum working pressure 16.0 Bar. Maximum operating temperature 99°C.
Range of regulating valves, consisting of a brass body with thermostatic control elements and manually adjustable flow control valve. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of manually adjustable thermal balancing valves (brass body) supplied with a temperature gauge. TREG models: Maximum working pressure 10.0 bar. Maximum operating temperature 99°C. SBTREG models: For use with copper pipe (BS EN1057), maximum working pressure 10.0. Maximum operating temperature of 95°C.
'Purtop 1000 N'. Factory applied, two component, grey coloured polyurea coating. Mix components A & B in a weight ratio of 1:1 and apply as per manufacturer's TDS '7506-3-2024'. Cure for 48 hours@23°C. Between September 2022 and August 2024, the coating is for use with water up to 23°C. From September 2024, the coating is for use with water up to 60°C. This material is only approved for the mixing, curing & soaking conditions that appear on the approval. If the mix/cure/soak conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EDELPOXY FNSL 151'. Factory applied, two-component, grey coloured epoxy coating. Mix base and hardener in a 2:1 volume ratio and apply as per manufacturer's instructions for use, reference number 'PC 151', dated January 16, 2015. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SUPERPOXY 5000RP'. Factory applied, two component, blue coloured epoxy coating. Mix Parts A & B in a volume ratio of 3:1 and apply as per manufacturer's instructions issue reference 'SPI 20170413 ' dated September 1st, 2016. Cure for 58 hours@24°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL'. Factory applied, grey coloured ordinary portland cement. Mix cement, sand & water in a 1:1.5:0.5 weight ratio and apply as per work instructions 'JSAW/SMG/DISP/PRO/WI-11', version '3.3', effective date '15.04.2024'. Cure for 2.5 hours@48°C and then 3 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'JSAW-JAL (OPC-JKL)'. Factory applied, grey coloured ordinary portland cement. Mix cement, sand & water in a 1:1.5:0.5 weight ratio and apply as per work instructions 'JSAW/SMG/DISP/PRO/WI-11', version '3.3', effective date '15.04.2024'. Cure for 2.5 hours@48°C and then 3 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'KUBOTA Moderate Heat Portland Cement'. Factory applied, grey coloured Portland Cement. Mix sand:cement;water in a 2.4:1.0:0.4 weight ratio and apply as per manufacturer's instructions 'KBT20250107', dated '7th January 2025'. Cure for 6 hours @40°C followed by 18 hours @20°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'JSGL-SRC (U)'. Factory applied, grey coloured Sulphate resistant cement. Mix cement:sand:water in a 1:1.7:0.4 weight ratio and apply as per manufacturer's Work Instructions 'JSGL/WI/14', issue no, '02', revision no. '00', dated '29.09.2018'. Cure for 24 hours@23°C and then 4 hours@45°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'JSGL-OPC (E)'. Factory applied, grey coloured Ordinary Portland cement. Mix cement:sand:water in a 1:1.7:0.4 weight ratio and apply as per manufacturer's Work Instructions 'JSGL/WI/14', issue no, '02', revision no. '00', dated '29.09.2018'. Cure for 24 hours@23°C and then 4 hours@45°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'JSGL-OPC (U)'. Factory applied, grey coloured Ordinary Portland cement. Mix cement:sand:water in a 1:1.7:0.4 weight ratio and apply as per manufacturer's Work Instructions 'JSGL/WI/14', issue no, '02', revision no. '00', dated '29.09.2018'. Cure for 24 hours@23°C and then 4 hours@45°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'BELPA CSA 50'. Light green coloured, NBR/fibre gasket material manufactured by calendaring. Shore hardness 65. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'Miflex Type 103'. Dual layered, extruded PVC hoses comprising of a polyester reinforced black coloured inner layer and grey, red or blue outer layer. For use with water up to 60°C.
'Silvina Grease'. Off-white coloured (opaque) silicone grease. Apply as per manufacturer's instructions. For use with water up to 65°C.
‘DENYL 6 5010 NERO 0300, DENYL 6 3010 NERO 0300, DENYL 6 1510 NERO 0300, DENYL 6 5010 NERO, DENYL 6 3010 NERO & DENYL 6 1510 NERO’. Black coloured, injection moulded, glass fibre filled PA6 materials. For use with water up to 85°C.
'Grilon AG-50 FWA Black'. Black coloured, injection moulded PA66-GF50 material. For use with water up to 60°C.
'Mapex® AN4720SN (+)'. Natural (appears beige coloured), injection moulded, glass fibre reinforced PA66 material. For use with water up to 85°C.
Grilamid LBV-30H FWA natural & black 9225. Grilamid LBV-50H FWA natural & black 9225. Grilamid LBV-65H FWA natural & black 9225. Glass filled (30%, 50% & 65%), injection moulded nylon material available in natural and black colours. For use with water up to 85°C.
'ULTRAMID® A3K FC Aqua Uncoloured'. Uncoloured, (appears beige), injection moulded PA66 material. For use with water up to 85°C.
'CCP Longlite® PBT 1100-600S'. Off-white coloured, injection moulded PBT material. For use with water up to 50°C.
'CIPHON HDPE PIPE PE100'. Black coloured (with blue stripe), extruded PE100 pipe. For use with water up to 65°C.
'Sabic 576S'. White coloured, injection moulded polypropylene material. For use with water up to 85°C.
'BA160E-8229-01'. Black coloured, injection moulded polypropylene material. For use with water up to 85°C.
'17520'. Black coloured, calendared, Chlorobutyl material. Shore hardness 50. Tested in-radius size 1.1mm. For use with water up to 65°C.
'WRC EPDM 92645'. Black coloured EPDM liner manufactured by calendaring. Shore hardness 80 A. Tested in-radius size 0.5mm. For use with water up to 23°C.
'F3352'. Black coloured, compression moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 0.65mm. For use with water up to 85°C.
'KF945W, KF955W, KF965W & KF975W'. Black coloured, compression moulded, silicone rubber materials. Shore hardness between 45 & 75. Tested in-radius size 1.0mm. For use with water up to 85°C.
Range of stop valves with plastic bodies. The valves incorporate a built-in solenoid valve which is operated by a switch located on the valve or by a remote control. The leak detector supplied with models SVSM66MRD & SVSM44MRD is not connected to any water pipe, is independent of the valve and is intended to be installed in the area at risk of leakage. It is intended to detect leakage and sends an electrical signal to close the valve. Please note that claims of leak detection have not been verified by WRAS For use with copper pipe (manufactured to BS EN1057), PEX pipe (manufactured to BS7291-3) and PB pipe (manufactured to BS7291 -2). Maximum working pressure 10.0 bar. Cold water use only.
Range of single-hole, multiple outlet, swivel, (brass bodies - various finishes) a quarter turn ceramic disc controlling the flow to the swivel arm with a dome type operating member and a ceramic cartridge with a single lever controlling the flow to the pull-down spray outlet incorporating a plastic aerator. Maximum working pressure: 10.0bar Maximum operating temperature 60°C
Page 129 of 171
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
