'Powertherm PP-R pipe'. Green coloured, extruded PP-R pipe (manufactured from SABIC Vestolen P 9421). For use with water up to 85°C.
'POWERtherm PP-R Fittings'. Green coloured, injection moulded PP-R fittings (manufactured from SABIC Vestolen P 9421). For use with water up to 85°C.
'PRO V500 V4'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions version '9', dated 'October 2022'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'vinyl eco/EASF'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions dated 25/09/2017. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'9710-ALT 'O' rings'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 80. Tested in-radius size between 1.0mm & 2.0mm. For use with water up to 23°C.
'01/U70EP 'O' ring' with a tested in-radius size between 0.5mm & 3.5mm. In June 2024, the follow components were added to the approval: ‘01/U70EP Cylindrical Gasket’ with a tested in-radius size between 0.9mm & 1.25mm. ‘01/U70EP Membrane’ with a tested in-radius size between 2.1mm & 5.5mm. Black coloured, injection moulded EPDM components. Shore hardness 70 For use with water up to 85°C.
‘ME0996’ components. Black coloured, injection moulded NBR rubber components. ‘O’-rings with an in-radius size of between 0.5mm & 5.0mm. Shore hardness between 40 & 90. Between November 2023 and April 2024, the approval included gaskets with an in-radius size of 5.0mm. Shore hardness 40. From May 2024 the gasket range was extended to include gaskets with an in-radius size of between 0.5mm & 5.0mm. Shore hardness between 40 & 90. For use with water up to 23°C.
'Griffon Silpat'. Grey coloured jointing compound. Apply as per manufacturer's instructions '7001669', issue '1'. For use with water up to 85°C.
Range of screw down stop valves with plastic bodies incorporating EPDM ‘O’-rings and seal. For use with PE-X pipe (manufactured to BS7291-3), BPB pipe (manufactured to BS7291-2) and copper pipe (manufactured to EN1057). Maximum working pressure and operating temperatures: 12.5 bar @ 20°C & 6.0 bar @ 65°C.
Bidet seat assembly which discharges via a sensor actuated solenoid valve and utilises a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). The inlet incorporates a strainer and flow regulator. Maximum working pressure 10.0 bar. Cold water supply only.
Range of single hole, single outlet, electronic touch free, deck mounted taps (chromium plated brass) for cold or premixed water. Flow is controlled via solenoid valves, actuated by infra-red sensors. Power is supplied by externally mounted 9V battery pack or 9V transformer. The inlet hoses have a stainless-steel strainer and the spout outlets incorporate plastic aerators. Maximum working pressure 8.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet, electronically controlled tap assemblies (chrome/satin plated brass body). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Supplied with a stainless steel braided PEX lined flexible connection hose. Maximum working pressure 8.0 Bar.
Non-metallic materials and components comply with BS6920 at 70°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The main body incorporates a stainless-steel strainer prior to the solenoid. Maximum working pressure 8.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Wall mounted, metal, single outlet, fixed combination tap assemblies. Flow is controlled by a solenoid valve activated by via an infra-red sensor and temperature adjusted via a single lever operating member. The Inlets incorporate stainless steel strainers & approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted, single hole, single outlet, fixed, electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled via an infra-red activated solenoid valve and the spout outlets incorporate a plastic aerator. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies in (chrome plated brass bodies). Flow is controlled with a solenoid valve activated via an infra-red sensor. The temperature is controlled via a single lever operating member on the body. The inlets incorporate stainless steel strainers and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlets incorporate a plastic aerator. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (stainless steel or brass bodies – various finishes). Flow is controlled via solenoid valve (housed in a control box) actuated via an infra-red sensor, the inlets to the control box incorporate stainless steel strainers. The spout outlets incorporates plastic aerators. The products incorporate a stainless steel PEX lined flexible hose assembly, connecting the tap to the solenoid valve. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of floor mounted, single-hole, single outlet (fixed), combination tap assemblies (chromium plated brass bodies), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to shower outlet. The spout outlet incorporates a plastic aerator. The product is supplied with a shower hose and handset. Maximum working pressure 5 bar. Maximum operating temperature 85°C
Range of Type TK spring loaded, resilient trim, in-line check valve cartridges. For insertion into specifically dimensioned bores. Maximum working pressure 10.0bar. Maximum operating temperature 65ºC.
Single hole, single outlet (fixed) over the rim (swivel nozzle) bidet combination tap assembly with a brass body (various finishes) incorporating a ceramic cartridge headwork with single lever operating members. The spout outlet incorporates a plastic aerator. The product is supplied with a lever operated pop-up waste - not verified by test. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Page 127 of 204
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
