'E7015WRC'. Black coloured, compression moulded EPDM sheet material. Shore hardness 70. Tested in-radius size 1.1mm. For use with water up to 85°C.
'EPDM H 85'. Black coloured, compression moulded EPDM rubber material. Shore hardness 85. Tested in-radius size 1.10mm. For use with water up to 70°C.
'Z440'. Black coloured, compression moulded FKM 'O' ring. Shore hardness 70. Tested in-radius size 5.0mm. For use with water up to 85°C.
'SN-738PF'. Black coloured, compression moulded NBR rubber. Shore hardness 71. Tested in-radius size 1.0mm. For use with water up to 23°C. From December 2023, the material is suitable for use with water up to 85°C.
‘N70 60 003 197’. Black coloured, injection moulded NBR material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'Akfix PS253 Pipe Sealant Medium Strength'. Blue coloured pipe sealant. Apply as per manufacturer's TDS 'Rev.01', issue date '23/10/2019'. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hinton Thread Sealant HTS50 & HTS250'. Anaerobic adhesive which is available in a yellow colour or in a yellow/orange colour. Apply as per manufacturer's instructions dated '2023-06-07', 'review 6' and cure for 15 minutes@25°C or 24 hours@22°C. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions.
'Hinton Solvent Cement HSC125 & HSC250'. Clear, transparent (un-pigmented) solvent cement, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions 'Rev00 02062023'. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'IRWR55'. Black coloured, compression moulded IIR rubber membrane/diaphragm. Shore hardness 51. Tested in-radius size 1.01mm. For use with water up to 23°C.
Side entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by an electronically controlled flush valve. Maximum working pressure 10.0 bar. Cold water use only
WC flushing cistern incorporating a side entry BS 1212-4 compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by electronic or manual actuation. Maximum working pressure 10.0 bar. Cold water use only
Range of concealed WC dual flushing cisterns with a vertical BS 1212-4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly. The product also incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10 Bar, cold water use only.
Three-hole, single outlet (fixed), combination tap assembly (brass body – various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to the shower outlet. The product is supplied with a stainless-steel braided EPDM lined flexible connection hose to connect the head work to the spout outlet. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Wall mounted, three-hole, single outlet, fixed combination tap assembly (chrome plated brass body), incorporating a ceramic cartridge headwork with a single lever operating member. The product is supplied with a shower handset holder that incorporates a manual diverter and a cascade type spout outlet. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted, three-hole, single outlet, fixed combination tap assemblies (brass bodies – various finishes). Incorporating ceramic cartridge headworks with single lever operating members. The product incorporate shower handset holders that incorporate manual diverters. The spouts incorporate plastic aerators. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
DC pipe interrupter with nylon body. The inlet incorporates a plastic flow regulator. Maximum working pressure 10 Bar Cold water use only
Range of non-verifiable single check valve assemblies with DZR brass bodies. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of ceramic disc headworks with brass bodies and EPDM rubber ‘O’-rings for insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of quarter turn ceramic disc headworks with brass bodies and NBR ‘O’ rings, for insertion into specifically dimensioned bores. Maximum working pressure 10.0 Bar Maximum operating temperature 85.0°C
Non-metallic materials and components comply with BS6920 at 85°C
Ceramic cartridge headwork with a PPO body and silicone gaskets for insertion into specifically dimensioned bores. Maximum working pressure 5.0 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of ceramic cartridge headworks with plastic bodies and EPDM ‘O’-rings for insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (chrome plated) and pull-out spray. The products incorporate a ceramic cartridge headwork with single lever operating member. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (various finishes), incorporating ceramic cartridge headworks, and single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet fixed combination tap assemblies (brass body with various finishes), incorporating a ceramic cartridge headwork with either a single lever or cross top operating member. The spout outlets incorporate a plastic aerator. Products are supplied with PEX inner-lined grey plastic braided inlet hoses. Maximum working pressure 10 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single-hole, single outlet, (fixed), combination tap assemblies, (chrome plated brass bodies. Incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates plastic aerators. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of single-hole, single outlet, fixed combination tap assemblies, (chrome plated brass bodies), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. The products are supplied with click type pop-up wastes Maximum working pressure 5 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of floor mounted single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes). Incorporating a ceramic cartridge headwork with either a lever or joystick type operating member and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic aerator. The shower outlet connection incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet (swivel) combination tap assemblies, brass bodies with (various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with an approved installation kit consisting of stainless-steel braided EPDM lined flexible hose assemblies with ½” BSP (F) captive nut end connections with 15mm compression single check valve assembly (suitable for backflow protection against Fluid Category 2) verified by test that also incorporates an isolation valve, intended for installation at each inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet, (swivel) combination tap assemblies, (brushed stainless steel brass bodies). Incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. The products are supplied with metal back nuts. The inlets are supplied with stainless steel strainers. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C
Single hole, single outlet (swivel) combination tap assembly with (brass bodies - various finishes), incorporating a ceramic cartridge headworks and single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes). Incorporating a ceramic cartridge headwork and a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (swivel) combination tap assembly (chromium plated brass) incorporating a ceramic cartridge headwork with a single lever type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single-hole,single outlet, (swivel) combination tap assemblies (brass bodies – various finishes). Incorporoating ceramic headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 60°C
Range of single-hole, single outlet, (swivel), combination tap assemblies (chorme or supersteel plated brass bodies). Incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly (stainless steel body) incorporating a ceramic cartridge headwork with single lever type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assemblies (brass body - varies finishes incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Wall mounted two hole, single outlet (fixed) combination tap assemblies (brass bodies, various finishes), incorporating ceramic cartridge headworks and single lever operating members. The spout incorporates a plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of two-hole, single outlet (fixed), combination tap assemblies (brass bodies – various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spouts incorporate waterfall outlets with stainless steel strainers. The products are supplied with metal back nuts. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Two-hole, single outlet, (fixed) combination tap assemblies, (brass bodies – various finishes) incorporating a quarter turn ceramic disc headwork and a thermostatic cartridge with cubed type operating members incorporating a manual override button. The spout outlet incorporates a plastic aerator. The inlets incorporate approved check valve cartridge(s); however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Wall mounted, two hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating a ceramic cartridge headwork with single lever operating member. The product also incorporates a manual diverter to shower outlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Wall mounted bar type thermostatic bath shower mixer (chromium plated brass), incorporating a diverter valve controlling the flow to either the spout outlet or shower outlet with a single lever operating member with manual override. The temperature is controlled independently via a thermostatic cartridge using a single lever or dome type operating members with a manual override. Both inlets incorporate an approved single check valve cartridge (however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection) and stainless-steel strainers. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Wall mounted two-hole, single outlet (fixed) combination tap assembly (brass bodies - various finishes) incorporating a ceramic cartridge headwork with a single lever operating member, and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 70°C
Range of wall mounted, two-hole, single outlet (fixed) combination tap assembly (chrome plated brass body) incorporating a ceramic cartridge headwork with a single lever operating member and self-cancelling diverter to shower outlet. The shower outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Deck mounted, two hole, single outlet fixed combination tap assemblies (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members and self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic aerator and the products are supplied with metal backnuts, shower hose and handset. The shower outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow prevention. Maximum Working Pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Two hole, wall mounted, single outlet fixed combination tap assemblies (chromium plated brass) incorporating a ceramic cartridge headworks with a single lever operating member and self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic aerator. Maximum Working Pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted, concealed, three hole single outlet (fixed) combination tap assemblies with brass bodies (various finishes), incorporating quarter turn, ceramic disc headworks with cross top (14415W-3-CP) or single lever (14415W-4-CP) operating members. The spout outlet incorporates a plastic aerator. Maximum operating temperature 60°C. Maximum operating pressure 4.1 bar.
Range of deck mounted three hole single outlet (fixed) combination tap assemblies with brass bodies (chromium plated), incorporatinig ceramic disc headworks with cross top (14428W-3-CP) or single lever (14428W-4-CP) operating members. The product is supplied with stainless-steel braided EPDM lined flexible hose assemblies to connect the headworks to the spout outlet. Spouts incororate plastic flow straightners. Maximum working pressure 5 bar. Maximum operating temperature 60°C
Range of combined bath fillers and overflow waste assemblies with plastic bodies (various finishes). The outlet incorporates a plastic aerator and the product is supplied with a cable operated pop-up waste. Maximum operating temperature 60°C.
Range of deck mounted, four hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a 2-way ceramic disc diverter headwork controlling the flow between the spout and shower outlet. Temperature is controlled independently by a thermostatic cartridge. The ARR-132T-CP model has single lever operating members and the ARR-232T-CP model has cross top operating members. Each inlet incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. The product is supplied with a shower hose and handset, and has metal backnuts. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Page 126 of 222
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
