Range of press fit spherical valves with chrome plated brass bodies, to be used with copper pipe EN1057. Crimp joint is achieved by a M profile crimp. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with either brass (BFIVB-15, BFIVBL-15 & BFIVHPL-15 models) or nickel plated (BFIV-15, BFIVL-15,BFIVL-22 & BFSVB-15D models) brass bodies with chrome plated brass ball and operated via lever, butterfly type handle or screwdriver slot. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of lever or handwheel operated spherical valves with stainless steel body, stainless steel ball and PTFE seals. Maximum working pressure 20.0 Bar (Models Series 65 & Series 73) Maximum working pressure 50.0 Bar (Models Series 66 & Series 74) Maximum operating temperature 85.0°C
Range of gate valves with either brass or DZR brass bodies. The valves incorporate non-rising spindle headworks with a wheel type operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
Range of gate valves, (brass bodies) controlled via a handwheel with PTFE seals. Maximum working pressure 20.0 bar (L198 models), 16.0 bar (L197 & P474 models). Maximum operating temperature 99°C
Range of gate valves incorporating DZR brass bodies, spindle headwork and hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C
Range of hand wheel operated or key operated gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM. Models WVF‐002A & WVF‐002B incorporate brass valve seats Maximum working pressure 16.0 Bar Maximum operating temperature 65.0°C
Ranges of gate valves with ductile iron bodies (blue epoxy coated), and EPDM coated wedge with hand wheel operating members. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
Range of gate valves with bronze bodies and wedges. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure: 25 Bar. Maximum operating temperature: 85°C.
Range of flanged gate valves with blue epoxy coated ductile iron bodies and EPDM O-rings and disc. The valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of hand wheel operated gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C
Range of Gate valves with ductile iron bodies (blue epoxy coated), EPDM rubber coated wedges, non-rising spindles with hand wheel operating members. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies, and an EPDM wedge, gasket and ‘O’-ring. The TCDIGVR16 & TCDIGVR25 models has a rising spindle, the TCDIGVN16 & TCDIGVN25 models has a non-rising spindle, both have a handwheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM coated wedges and hand wheel operating members. Maximum working pressure: 16.0 Bar. Maximum operating temperature: 80°C.
Range of gate valves with brass bodies and wedges. Maximum working pressure 17.5 bar. Maximum operating temperature 93°C
Range of resilient seated gate valves incorporating ductile iron bodies with blue epoxy coated finish. The valves incorporate either rising (G series) or non-rising spindles (GNS series) and have an EPDM wedge. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated ductile iron bodies and handwheel operating members. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of double regulating valves available with DZR brass, lead free brass or bronze bodies (see models). Products incorporate a non-rising spindle headwork. Products also include two test ports. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of double regulating valves available with DZR brass, lead free brass or bronze bodies (see models). Products incorporate a non-rising spindle headwork. Products also include two test ports. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of electromagnetic scale inhibitors with stainless steel bodies. Maximum working pressure: 16.0 bar. Cold water use only.
Range of UV disinfection units with stainless steel bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 35°C.
Range of UV Disinfection units with stainless steel bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of inline water meter kits incorporating brass bodies, a spherical valve and drain off valve. For use with copper pipe (manufactured to BS EN 1057:1996). Maximum working pressure 10.0 bar. Cold water use only.
'Jotapipe IL 6001-120S'. Factory applied, blue coloured, fusion bonded epoxy powder coating. Pre-heat substrate to be coated for 15 minutes@200°C and coating applied as per manufacturer's TDS dated '22 August 2018'. Post-cure for 15 min@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chosui Coat Grey'. Factory applied, grey coloured (once mixed and applied), two-component epoxy resin coating, Mix base:hardener in a 2:1 weight ratio and apply as per PDS 'CN：IF438122003', dated '03/06/2022'. Cure for 7 days@30°C and then 7 days@60°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Kubota Powder TK1413F (SPD)'. Factory applied, grey coloured epoxy resin coating. Apply as per manufacturer's TDS 'RP23242', dated 'December 26, 2023'. Cure for 6 minutes@180°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Kubota Powder TK1413F I'. Factory applied, grey coloured epoxy resin coating. Apply as per manufacturer's PDS '4384-23-403' dated '2023/11/16'. Cure for 10 minutes@200°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'V-PET#1340QD-F GRAY'. Factory applied, grey coloured epoxy resin coating. Apply as per manufacturer's instructions '2211447-2' dated '2023/11/16'. Cure for 20 minutes@180°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘EKOPIPE 900 Blue’. Factory applied, blue coloured, two-component epoxy coating. ‘EKOPIPE 900 Red’ was added to the approval in March 2026. Factory applied, red coloured, two-component epoxy coating. Mix parts A & B in a mass ratio of 2:1 and apply as per manufacturer's TDS 'No:09, Rev.Date: January 2021'. Cure for 7 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EVER-SRC-1'. Factory applied, grey coloured Sulphate Resistant cement. Mix cement and sand in a 2:1 mass ratio. Apply as per manufacturer's instruction sheet '2024-09-10', revision 'A0'. Steam cure for 8 hours@50°C. For use with water up to 65°C.
'NATCEM 35'. Site applied, grey coloured natural cement mortar. Mix cement mortar with water in the ratio of 25kg:3.6 litres and apply as per manufacturer's IFU 'issue 4', dated '21 February 2023'. Cure/set for 4 hours@0°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Promag D - Flowtube'. Black coloured, injection moulded PA flowtube. For use with water up to 60°C.
'KN133G30 (off-white in colour) & KN133G15BL (black coloured)'. Injection moulded PA6 materials. KN133G30 is for use with water up to 65°C. KN133G15BL is for use with water up to 23°C.
'SUDA HDPE Fittings'. Black coloured, injection moulded HDPE fittings. For use with water up to 60°C.
'Draka Comteq Cable Sheath: R607581 and R698927. Black coloured, extruded polyethylene cable sheath. For use with water up to 85°C.
‘Georg Fischer (+GF+) HDPE PE100 Pipes and ‘Hepworth MDPE PE80 Pipes’. Black coloured (with or without blue stripes), extruded PE100 pipes. Black coloured, extruded PE80 pipes. For use with water up to 60°C.
'HEPWORTH Pipe'. Black coloured, extruded LDPE pipe. For use with water up to 60°C.
'Hepworth MDPE PE 80 Black Pipe'. Black coloured (with blue external stripes), extruded MDPE pipe. For use with water up to 60°C.
+GF+ MDPE PE 80 Black Pipe'. Black coloured (with blue external stripes), extruded MDPE pipe. For use with water up to 60°C.
‘+GF+ HDPE PE100 Pipes' and '+GF+ MDPE PE80 Pipes’. Black coloured (with or without blue stripes), extruded PE100 pipes. Black coloured, extruded PE80 pipes. For use with water up to 60°C.
'+GF+'. Black coloured, extruded LDPE pipe. For use with water up to 60°C.
'PF HDPE Fittings'. Black coloured, injection moulded HDPE fittings. For use with water up to 60°C.
'ELGEF PLUS'. Black coloured, injection moulded HDPE electrofusion and spigot fittings. For use with water up to 60°C.
'FLEXIPOL MASA'. Black coloured (with blue stripes), extruded polyethylene pipes. For use with water up to 60°C. The 'FLEXIPOL MASA' pipes covered by the scope of this approval are marked with 'V63'. 'FLEXIPOL MASA' pipes which are not marked with 'V63' are not covered by the scope of this approval.
'Kasta® HDPE PE 100 Pipe (Black)'. Black coloured (with blue external stripes), extruded HDPE pipe. For use with water up to 65°C.
'Revolve N-461 Natural'. White coloured polyethylene material manufactured by rotational moulding. For use with water up to 85°C.
'ISOMAG Cylinder'. Grey coloured, extruded polypropylene cylinder component. For use with water up to 60°C.
'Verplen C3008 VE ACLKUV W (GF 30% green coloured) & Verplen 60NE A W (black coloured'. Injection moulded, polypropylene materials. For use with water up to 60°C.
'+GF+ uPVC Pressure Pipe'. Grey coloured, extruded uPVC pipe. For use with water up to 60°C.
'798F'. Black coloured, injection moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 60°C.
Page 122 of 177
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
