Range of T-Type thermostatic mixing valve (chromium plated brass). For use with copper pipe to BS EN1057. Maximum working pressure; 10 Bar Maximum operating temperature 85°C.
Range of thermostatic blending valve (chromium plated brass). The inlets incorporate stainless steel strainers and single check valve cartridges, however the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of wall mounted bar type shower mixing valve (brass body, various finishes - see model). The product incorporates a ceramic cartridge headwork with a single lever operating member. The hose outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C.
Range of butterfly valves with blue epoxy coated, ductile iron bodies and either blue epoxy coated ductile iron or stainless-steel discs and EPDM seats and ‘O’-rings. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C
Range of wafer and fully lugged butterfly valves with a blue epoxy coated cast iron bodies, EPDM seat and a stainless steel (2302/2502 models) or chrome plated iron disc 2304/2504 models). Products are either handwheel (H) or gear (G) operated (see models). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Ranges of wafer or lugged butterfly valves with blue epoxy coated ductile iron bodies incorporating EPDM seat. The valves can be supplied with either Stainless steel, Nickel or blue epoxy coated ductile iron discs. Maximum working pressure: 16.0bar. Maximum operating temperature: 85°C.
Range of plastic, ceramic disc diverter valves. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Concealed three-way diverter valve with various body finishes and EPDM ‘O’-rings. Also supplied with various trim sets. Maximum working pressure 5.0 Bar. Maximum operating temperature 85°C.
Range of ‘901’ float operated equilibrium inlet valves incorporating brass bodies and float arms. Maximum working pressure - See Models Maximum operating temperature – Cold water use only.
Range of deck mounted flow control valves (brass bodies - various finishes) incorporating a quarter turn ceramic disc headwork and a single lever or cross top operating member. Maximum working pressure 5.0 Bar Maximum operating temperature 85.0°C
Range of eccentric plug valves with blue epoxy coated ductile iron bodies, PTFE washers a stainless steel plug which is fully encapsulated with EPDM. Maximum working pressure 16 Bar. Maximum operating temperature 80°C.
Range of globe type spring loaded, resilient trim, non-return valves with epoxy coated ductile iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C
Range of globe type spring loaded, resilient trim, non-return valves with epoxy coated ductile iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C
Range of spring-loaded non-return valves with stainless steel bodies. Maximum working pressure 24.5 bar. Maximum operating temperature 85°C
Range of swing gate, non-return valves with (blue, black or red epoxy powder coated) ductile iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of wafer or globe type spring loaded, resilient trim, non-return valves with cast iron bodies (blue epoxy powder coated). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of non-return, swing gate valves with bronze, DZR brass or brass bodies and DZR brass, bronze or brass discs. Maximum working pressure 20.0 bar or 16.0 bar (please refer to model) Maximum operating temperature 85°C.
Range of pilot operated pressure reducing valves with blue epoxy coated ductile iron bodies. The valves have an adjustable pressure reducing facility controlled via a pilot valve (with an operating range of 1 to 6 bar), with auxiliary components including stainless steel tubing, fittings and spherical valves. Maximum working pressure 16.0 bar. Maximum operating temperature 23°C.
Spherical valves incorporating bronze bodies with lever operating members, chromium plated brass ball and PTFE seat. Maximum working pressure 25.0 bar, Maximum operating temperature 85°C.
Range of lever models S3727, S3737, S3747, S3758, 85986, 85987 & 85988 or screwdriver operated (all other models) spherical ball valves with brass bodies and a chromium plated brass ball. Max working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of lever or butterfly lever operated spherical valves, incorporating a nickel plated brass body and stainless steel ball, PTFE seats and NBR ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with DZR brass bodies and brass ball. For use with copper pipe manufactured to EN1057. Maximum working pressure 25.0 Bar Maximum operating temperature 85.0°C
Range of gate valves incorporating bronze bodies and wedges with PTFE seals. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating bronze bodies and wedges with PTFE seals. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves with brass bodies, bonnets and non-rising stems, with hand wheel or lockshield operating members. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of resilient seated gate valves with a blue epoxy coated ductile iron body and a ductile iron gate/wedge which is fully encapsulated with EPDM. Maximum working pressure 16.0 Bar. Maximum operating temperature 80.0°C.
Range of hand wheel operated or key operated gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM. Models HY-002A & HY-002B incorporate brass valve seats Maximum working pressure 16.0 Bar Maximum operating temperature 65.0°C
Range of regulating valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
‘Aquastrom’ range of regulating valves with brass bodies. Maximum working pressure 16.0 Bar Maximum operating temperature 90.0°C
Range of in-line water conditioners with stainless steel bodies and catalytic alloy core. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of ultraviolet disinfection units with stainless-steel bodies. Maximum working pressure 16.0 bar. Cold water use only.
'Ronfalin ABS 609 White 2097P'. White coloured (opaque), injection moulded ABS materials. For use with water up to 85°C.
'VSS1'. Dark grey coloured, sintered silicon carbide washer. For use with water up to 85°C.
'ENDOPRENE® 851 Blanc'. Factory applied, white coloured, two-component polyurethane coating. Mix parts A & B in 50:50 volume ratio and apply as per manufacturer's TDS dated 10/07/2024. Cure for 6 days@40°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'175-767 Polyester blue 5012'. Factory applied, blue coloured polyester coating. Apply as per manufacturer's instructions updated '15.03.2018'. Cure for 10 minutes@180°C. For use with water up to 55°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Series 2000 RAL 5015'. Factory applied, blue coloured epoxy resin coating. Apply as per manufacturer’s data application sheet ‘Revision: 6 (2018/10/01)’ created ‘2015/11/11’. Cure for 10 minutes@180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MJ-6'. Factory applied, blue coloured epoxy resin powder coating. Mix in a 63%/21.8%/13.2%/2% ratio and apply as per manufacturers instructions 'v1', dated '06-05-2023'. Cure for 60 minutes@200°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘NMSP2104 M & ER2104A01SM'. The following coatings were added to the approval in March 2025: ER2209A01SC, ER2252A01SC, ER2259A01SC & ER2260A01SC. Factory applied, blue coloured, porcelain (vitreous) enamel coatings. Apply as per manufacturer’s user manual 'PEM 38', edition '01' dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘PMSP5099-M & EP5099D01SC'. Factory applied, blue coloured, porcelain (vitreous) enamel coatings. Apply as per manufacturer’s user manual 'PEM 37', edition '01' dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PRIMGREEN® ENDURANCE & Primgreen LAT 12035' primers for use with 'RILSAN® PA11 T BLUE 7444 MAC (16293), PA11 T GREY 5161 MAC (17203), PA11 T WHITE 1488 AC (17219) & PA11 T BLACK 7450 AC (17185)' coatings. Factory applied primers and powder coatings. The piece to be coated is to be pre-heated to 330°C for 10 minutes, the primer and coating applied in accordance with user instructions 'Dircom - 4418E/05.2015/20' and then cured for 10 minutes@330°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘FlatSeal™HMF10’. Orange coloured NBR/aramid fibre gasket material, manufactured by calendaring. For use with water up to 85°C. For use only as a gasket material having been tested at a reduced surface area to volume ratio.
'MOLYguard HVG'. Clear silicone lubricant. Apply as per manufacturer's instructions. For use with water up to 85°C.
'Klüberbeta VR 67-3500'. Cream coloured silicone grease intended for use as a lubricant. For use with water up to 85°C.
'Syntheso LM 220'. White coloured (opaque) lubricant grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
'UNISILKON L 250 L'. White coloured (opaque) lubricant grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
'UNISILKON L 641'. White coloured (opaque) lubricant grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
'SAPPHIRE Endure Bearing Grease'. White coloured grease. For use with water up to 85°C.
'Turmsilon GL 320-G'. White coloured silicone grease/lubricant. For use with water up to 85°C.
'Ferrimax 35h with Parylene Coating'. Sintered ferrite magnet encapsulated in grey coloured coating. For use with water up to 85°C.
'Relon A500 Nero 4095 GF30 K'. Black coloured, injection moulded, glass filled PA66 material. For use with water up to 80°C.
Page 112 of 158
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
