'Topilene R202P'. White coloured, extruded polypropylene material. For use with water up to 85°C.
'PRO V500 V4'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions version '9', dated 'October 2022'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chemfix 100'. Site applied, grey coloured chemical anchor resin. Apply as per manufacturer's instructions ref. no. 'rev5' dated 04/06/218. Cure for 48 hours@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'vinyl eco/EASF'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions dated 25/09/2017. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CH200'. Brown coloured chemical anchor resin. Apply as per manufacturer's instructions 'version 24/05/2018'. Cure for 24 hours@5°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
'Chemfix CH+ MAX'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions dated 18/05/2022. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPDM 70.502-03 washers & 'O' rings'. Black coloured, injection moulded EPDM washers and 'O' rings. Shore hardness 70. Tested in-radii sizes between 0.5 and 2.6mm. For use with water up to 85°C.
`SW EPDM`. Black coloured, extruded, EPDM hose. Shore hardness 85. Tested in-radii sizes between 0.75mm & 1.70mm. For use with water up to 85°C.
'E24 EPDM moulded parts.' Black coloured, injection moulded EPDM seals. Shore hardness 75. Type 1 moulded seals have a tested in-radius size of 4.2mm and Type 2 moulded seals have a tested in-radius size of 0.7mm. For use with water up to 85°C.
'01/U70EP 'O' ring' with a tested in-radius size between 0.5mm & 3.5mm. In June 2024, the follow components were added to the approval: ‘01/U70EP Cylindrical Gasket’ with a tested in-radius size between 0.9mm & 1.25mm. ‘01/U70EP Membrane’ with a tested in-radius size between 2.1mm & 5.5mm. Black coloured, injection moulded EPDM components. Shore hardness 70 For use with water up to 85°C.
'AquaFlex T 5857'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 70°C.
‘ME0996’ components. Black coloured, injection moulded NBR rubber components. ‘O’-rings with an in-radius size of between 0.5mm & 5.0mm. Shore hardness between 40 & 90. Between November 2023 and April 2024, the approval included gaskets with an in-radius size of 5.0mm. Shore hardness 40. From May 2024 the gasket range was extended to include gaskets with an in-radius size of between 0.5mm & 5.0mm. Shore hardness between 40 & 90. For use with water up to 23°C.
'NB7041F'. Black coloured, compression moulded NBR material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 65°C.
'Griffon UNI-100 XT'. Amber coloured solvent cement intended to join PVC pipe and fittings. Apply as per manufacturer's instructions '6300427', issue '1'. Cure for 24 hours@7°C. For use with water up to 35°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Paryls® PPSU F1550NC (natural grade – appears brown), F1550GY (grey coloured), F1550BK (black coloured) & F1550WH (white coloured)’. Injection moulded PPSU materials. For use with water up to 85°C.
Range of screw down stop valves with plastic bodies incorporating EPDM ‘O’-rings and seal. For use with PE-X pipe (manufactured to BS7291-3), BPB pipe (manufactured to BS7291-2) and copper pipe (manufactured to EN1057). Maximum working pressure and operating temperatures: 12.5 bar @ 20°C & 6.0 bar @ 65°C.
Bidet seat assembly which discharges via a sensor actuated solenoid valve and utilises a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). The inlet incorporates a strainer and flow regulator. Maximum working pressure 10.0 bar. Cold water supply only.
Range of wall mounted, single hole, single outlet, fixed, electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled via an infra-red activated solenoid valve and the spout outlets incorporate a plastic aerator. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies in (chrome plated brass bodies). Flow is controlled with a solenoid valve activated via an infra-red sensor. The temperature is controlled via a single lever operating member on the body. The inlets incorporate stainless steel strainers and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlets incorporate a plastic aerator. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet, fixed, electronically controlled combination tap assemblies, (chrome plated brass bodies). Flow is controlled via an infra-red activated solenoid valve and the spout outlets incorporate plastic aerators. A stainless steel braided PEX lined flexible hose connects the components. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 45°C
Single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlets incorporate a plastic aerator and flow regulator. The tap incorporates a soap dispenser with separate dispensing nozzle. Maximum working pressure 8.0 Bar. Maximum operating temperature 55°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (stainless steel or brass bodies – various finishes). Flow is controlled via solenoid valve (housed in a control box) actuated via an infra-red sensor, the inlets to the control box incorporate stainless steel strainers. The spout outlets incorporates plastic aerators. The products incorporate a stainless steel PEX lined flexible hose assembly, connecting the tap to the solenoid valve. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of floor mounted, single-hole, single outlet (fixed), combination tap assemblies (chromium plated brass bodies), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to shower outlet. The spout outlet incorporates a plastic aerator. The product is supplied with a shower hose and handset. Maximum working pressure 5 bar. Maximum operating temperature 85°C
Range of AB air gap arrangements (verified by test - suitable for backflow protection against Fluid Category 5), supplied with or without softeners and/or flow meters (see models). Maximum working pressure 10 bar. Maximum operating temperature 85°C
‘Waterblade Chrome’ tap outlet adaptor with a chromium plated plastic body. The product incorporates a plastic flow regulator and an integral stainless-steel strainer. Maximum operating temperature 60°C.
Range of ceramic cartridge headworks with plastic bodies and NBR seals and O-rings. For insertion into specifically dimensioned bores. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of ceramic cartridge headworks with plastic bodies and NBR rubber `O`- rings, for insertion into specifically dimensioned bores. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Ceramic cartridge headwork with plastic body & EPDM seals. For insertion into specifically dimensioned bores. Maximum working pressure 5.0 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Ceramic cartridge headwork with a plastic body incorporating EPDM ‘O’ rings and a stainless teel strainer. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of thermostatic cartridges with plastic bodies, stainless steel mesh strainer and EPDM ‘O’ rings. For insertion into specifically dimensioned bores.
Non-metallic materials and components comply with BS6920 at 85°C
Single-hole, single outlet, (swivel), combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The outlet is a pull-out spray type that incorporates a plastic aerator. The inlet of the cold supply hose and the pull-out spray handset both incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet, (swivel), combination tap assemblies (chromium plated brass bodies), incorporating quarter turn ceramic disc headworks and single lever operating members. The outlet is a pull down spray type and incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 65°C
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass bodies), incorporating a ceramic cartridge headwork with a single lever operating member. The outlet is a pull down spray type and incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 65°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. Some products are supplied with a lever type or click-type pop up waste. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Single hole, single outlet (with additional outlets for filtered cold water), fixed, combination tap assembly (various plated brass), incorporating a ceramic cartridge headwork and single lever operating member. The tap body incorporates an additional push type headwork that controls the flow to a second outlet. Both outlets incorporate plastic aerators. The product is supplied with a filter assembly supplied via a brass connecting tee. Models incorporate approved single check valve cartridges; however, the complete assembly has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of single-hole, single outlet, fixed, combination tap assemblies (brass bodies – various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. The products are supplied with click-type pop up wastes. Maximum operating pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes). Models (F1021 & F7132B) incorporate quarter turn ceramic disc headworks with either single lever or cross-top type operating members. Models (F1025X, F1026 & F7149) incorporate ceramic cartridge headworks with single lever operating members. All spout outlets incorporate plastic aerators. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Model V7K33YY-XX incorporates an additional outlet for a side spray connection. Maximum working pressure 3.0 Bar Maximum operating temperature 70.0°C
Single hole, single outlet (swivel) combination tap assembly, (chrome plated brass body), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator or flow straightener. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes), incorporating ceramic cartridge. The inlets incorporate stainless steel strainers. The spout outlets incorporate a plastic aerator or a flow straightener. Maximum working pressure 10 Bar. Maximum operating temperature 65 °C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator or flow straightener. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single-hole, single outlet (swivel) combination tap assemblies, (brass bodies – various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate plastic aerators. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Single hole, single outlet, swivel combination tap assembly (chrome plated brass body), incorporating ceramic cartridge headworks with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a dome type operating member to control the temperature. The spout outlet incorporates a plastic aerator and a detent headwork that controls the flow.. The inlets incorporate approved check valve cartridges however the complete product has not been fully tested to demonstrate It provides backflow protection. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of two-hole, single outlet (fixed) combination tap assemblies, (brass bodies – various finishes) incorporating quarter turn ceramic disc headworks with single lever operating members and a manual diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. Hose and handset not supplied. The products are supplied with metal back nuts. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of two-hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes), incorporating quarter turn ceramic disc headworks with single lever type operating members and a manual diverter to shower outlet. Hose and handset not supplied. The products are supplied with metal back nuts. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of two-hole, single outlet, (fixed), combination tap assemblies (chrome or matte black plated brass bodies), incorporating quarter turn ceramic disc headworks with single lever operating members and a manual diverter to a shower outlet. The spout outlet incorporates a plastic aerator. The products are supplied with metal back nuts. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Wall mounted, two hole, single outlet (fixed) combination tap assembly with (brass body - various finishes), incorporating a half-turn ceramic disc headwork with a dome type operating member, controlling and diverting the flow to a shower outlet. Temperature is controlled independently via a thermostatic cartridge with a dome type operating member incorporating a manual override button. The spout outlet incorporates a plastic aerator. The inlets incorporate stainless steel strainers and approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar
Non-metallic materials and components comply with BS6920 at 60°C
Page 109 of 236
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
