Range of regulating valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of UV disinfection units with stainless steel bodies. Maximum working pressure 10.3 bar. Maximum operating temperature 60°C.
Range of modular silver and copper disinfection ion generators with a stainless-steel bodies Maximum working pressure 9.0 bar. Cold water use only.
‘Ultraform® N2320 Aqua AT UNCOLORED’ & 'Ultraform® N2320 003 AT UNCOLORED'. Uncoloured (appears white), injection moulded C-POM material. For use with water up to 65°C.
'EASO ABS-CRN757K'. Grey coloured, injection moulded ABS material. For use with water up to 65°C.
'Ronfalin ABS 609 White 2097P'. White coloured (opaque), injection moulded ABS materials. For use with water up to 85°C.
‘BFSC Foug SDN’. Factory applied, grey coloured, blast furnace slag cement intended to line pipes. Mix sand and cement in a mass ratio of 1.5:1, then add water in a water/cement mass ratio of 0.36:1 and apply as manufacturer's instructions. Cure for 48 hours@23°C, 70% relative humidity. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ENDOPRENE® 851 Blanc'. Factory applied, white coloured, two-component polyurethane coating. Mix parts A & B in 50:50 volume ratio and apply as per manufacturer's TDS dated 10/07/2024. Cure for 6 days@40°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'175-767 Polyester blue 5012'. Factory applied, blue coloured polyester coating. Apply as per manufacturer's instructions updated '15.03.2018'. Cure for 10 minutes@180°C. For use with water up to 55°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Series 2000 RAL 5015'. Factory applied, blue coloured epoxy resin coating. Apply as per manufacturer’s data application sheet ‘Revision: 6 (2018/10/01)’ created ‘2015/11/11’. Cure for 10 minutes@180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CLEAN TECH PW (BG)'. Factory applied, two-component, blue coloured epoxy coating. Mix parts A and B in a volume ratio of 3:1 and apply as per manufacturer's TDS 'CCPL/TDS/R11/CRC/22-23/04/R13/BG/R1', dated '15.09.2022'. Cure for 7 days@30°C. Between August 2024 and January 2025, the coating is approved for use with water up to 23°C. Between February 2025 and August 2029, the coating is approved for use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'MPPL_RELIPOXY'. Carbon steel pipe coated with red/brown coloured epoxy coating. For use with water up to 65°C.
'Klüberbeta VR 67-3500'. Cream coloured silicone grease intended for use as a lubricant. For use with water up to 85°C.
'Unisilkon TK 002/500'. Colourless lubricating oil. Apply as per manufacturer's data sheet. For use with water up to 60°C.
'UNISILKON L 641'. White coloured (opaque) lubricant grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
'Relon A500 Nero 4095 GF30 K'. Black coloured, injection moulded, glass filled PA66 material. For use with water up to 80°C.
'ThorPlas-White Bearing'. Polyester component in the form of a white coloured, continuous cast tube. For use with water up to 65°C.
'WIN Spigot Fittings'. Black coloured, injection moulded PE100 spigot fittings. For use with water up to 60°C.
'+GF+ HDPE PE 100' (black and black with blue stripes)'. Extruded polyethylene pipes. For use with water up to 60°C.
'Baishi HDPE Fittings'. Injection moulded HDPE fittings available in black or blue colours. For use with water up to 65°C.
'Pexylene 50937 Natural, Black & Blue'. Rotationally moulded polyethylene materials available in natural (appears off-white), black & blue colours. For use with water up to 65°C.
'8108658 V0010_K LLDPE'. Blue coloured, roto-moulded LLDPE material. For use with water up to 23°C.
'8108658 V0010_V LLDPE'. Blue coloured, roto-moulded LLDPE material. For use with water up to 23°C.
FORTRON® natural (appears cream) or black coloured, injection moulded PPS materials. For use with water up to 85°C. Grades manufactured in Celanese Florence, USA: FORTRON® 1140L4 SF3001 NATURAL FORTRON® 1140L4 SD3002 BLACK DW (formerly known as FORTRON® 1140L4 BLACK SD3002). FORTRON® 1140L6 SD3002 BLACK DW (formerly known as FORTRON® 1140L6 BLACK SD3002). FORTRON® 1140L6 SF3001 NATURAL FORTRON® 4184L6 SF3001 NATURAL FORTRON® 4184L6 SD3002 BLACK DW (formerly known as FORTRON® 4184L6 BLACK SD3002). Grades manufactured in Celanese Nanjing: FORTRON® 1140L4 SF3001 NATURAL DW (formerly known as FORTRON® 1140 L4 SF3001 natur CN). FORTRON® 1140L4 SD3002 BLACK DW (formerly known as FORTRON® 1140 L4 SD 3002 black).
'Inoflon M 695'. White coloured (opaque), sintered PTFE material. For use with water up to 85°C.
'E 71 65 003'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 3.5mm. For use with water up to 85°C.
'EPDM70(E7-512K)'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 65°C.
'FDJ-75'. Black coloured, injection moulded FKM rubber material. Shore hardness 76. Tested in-radius size 1.03mm. For use with water up to 85°C.
'NBR N65WKZ'. Black coloured, injection moulded NBR rubber material. Shore hardness 59. Tested in-radius 1.0mm. For use with water up to 23°C.
'N65WKZ'. Black coloured, injection moulded NBR material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 23°C.
'NE7130 Grey 60'. Light grey coloured, injection moulded silicone rubber material. Shore hardness 60. Tested in-radius size 1.97mm. For use with water up to 85°C.
'Loctite 403'. Clear, liquid cyanoacrylate adhesive. Apply as per manufacturer's technical data sheet reference ‘2.6’, dated August 2012. Cure for 72 hours@22°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TruTite™ 313 Thread Lock'. Blue coloured pipe sealant. Apply as per manufacturer's TDS version '1.0 26/07/24'. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CORE®'. Blue coloured pipe sealant. Apply as per manufacturer's instructions version '1', issue date '26/07/24'. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The main body incorporates a plastic flow regulator and stainless steel strainer prior to the solenoid. The inlets to the main body of the GS10, CM10 & GH10 model variants incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. These models also have a manual temperature control operated by a single lever on the side of the body. The inlet hoses incorporate a TPE gasket. The models are supplied with or without a pop-up waste. The GS20 & GM20 model variants are single feed. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The inlets to the main body of the M10, GC10, MX10, A10 & L10 model variants incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection, these models also have a manual temperature control operated by a single lever on the side of the body. The inlet hoses incorporate a stainless steel strainer (M10, GC10, MX10, A10 & L10 model variants) or combined TPE washer and stainless strainer (M20, GC20, A20 & L20 model variants). The models are supplied with or without a pop-up waste. The M20, GC20 A20 & L20 model variants are single feed. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed), electronically operated tap assembly. The flow is controlled by a solenoid valve and activated via an infra-red sensor. Inlets are supplied with check valves (verified by test - suitable for backflow protection against fluid category 2). Maximum working pressure 6 bar. Maximum operating temperature 40 °C
Range of deck mounted, Infra-red electronic basin mixers with mixing device and adjustable temperature limiter. The tap incorporates EPDM O-rings. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The main body incorporates a stainless-steel strainer prior to the solenoid. Maximum working pressure 8.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of side and bottom entry BS1212-3 inlet valves, with plastic bodies and brass shanks. Maximum working pressure: 3.0 Bar low pressure and 14.0 bar high pressure Maximum operating temperature: Cold water use only.
BS1212-4 (2016) compact type float operated valve for WC flushing cisterns, side entry type. The inlet incorporates a plastic flow restrictor. Maximum working pressure 10.0 bar. Cold water use only.
Range of side and bottom entry BS1212-3 inlet valves, with plastic bodies and brass shanks. Maximum working pressure: 3.0 Bar low pressure and 14.0 bar high pressure Maximum operating temperature: Cold water use only.
Range of side and bottom entry BS1212-3 inlet valves, with plastic bodies and brass shanks. Maximum working pressure: 3.0 Bar low pressure and 14.0 bar high pressure Maximum operating temperature: Cold water use only.
Range of concealed WC flushing cisterns with a side entry BS 1212-4(2016) float operated inlet valve providing a type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two button assembly for a 6 or 3 litre flush volume. The cistern incorporates a servicing valve and a stainless-steel braided EPDM lined flexible hose assembly installed prior to the inlet valve. Maximum working pressure 10.0 Bar, Cold Water use only
Range of in-line non-verifiable single check valve assemblies consisting of a spring loaded resilient trim single check valve cartridge housed within a DZR brass body. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C for 105701. Maximum operating temperature 85°C for 105702.
Ceramic cartridge headwork with a plastic body, for insertion into specifically dimensioned tap assemblies. Maximum working pressure 16.0 Bar Maximum operating temperature 65.0°C
Range of ½ turn ceramic disc headworks, with brass bodies and EPDM seals, for insertion into specifically dimensioned tap assemblies. Maximum working pressure: 5 Bar. Maximum operating temperature: 85°C.
Single-hole, single outlet (swivel) combination tap assemblies (brass body – various finishes) incorporating a ceramic cartridge (F1054-**) or quarter turn ceramic disc (F1046-**) headwork with a single lever operating member. The products have a pull-out spray outlet which incorporates a plastic aerator and trigger mechanism that stops the flow (model (F1046-**) or changes the water pattern from straight flow to spray (F1054-**). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet fixed combination tap assemblies (various finishes), incorporating a ceramic cartridge headwork with a single lever (Elysian models) or dome type (Milani models) operating member. The spout outlet incorporates a plastic flow straightener (Elysian models) or a plastic aerator (Milani models). Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Single hole, single outlet (fixed) combination tap assemblies various finishes incorporating a ceramic cartridge headwork with various operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Page 107 of 177
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
