Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes), incorporating a push on/off headwork with rotary temperature control using dome type lever operating member. Both inlets incorporate stainless steel strainers an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Some models are supplied with lever type pop up waste (see model). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2205048

Expiry date:

31/05/2027

Note:

No testing performed on pop up waste.

Size:

Stainless steel braided PEX lined flexible hose assemblies incorporating 3/8” BSP captive nut end connections

Marking:

Hansgrohe on front of body.

Installation Requirements:

R001 R006 R009 R010

Model:

Models with a waste set: 71 750 xxx Hansgrohe Talis Select E Basin mixer 110 71 752 xxx Hansgrohe Talis Select E Basin mixer 240 72 040 xxx Hansgrohe Talis Select S Basin mixer 80 72 042 xxx Hansgrohe Talis Select S Basin mixer 100 72 044 xxx Hansgrohe Talis Select S Basin mixer 190 Models without a waste set: 72 041 xxx Hansgrohe Talis Select S Basin mixer 80 72 043 xxx Hansgrohe Talis Select S Basin mixer 100 72 045 xxx Hansgrohe Talis Select S Basin mixer 190 Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.

Manufacturer:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Auestrasse 5 - 9, 77761 Schiltach

Country

Germany

View All Listings by this Company

Wall mounted, single hole, single outlet (fixed) combination tap assembly with brass body (various finishes), incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2205052

Expiry date:

31/05/2027

Note:

Basic set 10902180 is not part of this approval

Size:

For use with basic set 10902180 which has ½" BSP (F) inlets

Marking:

AXOR on body

Installation Requirements:

R001 R010 R040

Model:

11 026 xxx AXOR Urquiola Single lever basin mixer Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.

Manufacturer:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Auestrasse 5 - 9, 77761 Schiltach

Country

Germany

View All Listings by this Company

Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies, various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener. Maximum operating pressure 5.0 bar. Maximum operating temperature 65°C.

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2205060

Expiry date:

31/05/2027

Size:

Stainless steel braided EPDM lined flexible hose assemblies incorporating ½” captive nut end connections.

Marking:

Roxor (brand of Ultra Finishing Ltd.) on rear of body

Installation Requirements:

R001 R006 R010

Model:

WIN305 Windon Mono Basin mixer (Chrome), ARV305 Arvan Mono Basin mixer (Chrome), WIN370 Windon High Rise mixer (Chrome), ARV370 Arvan High Rise mixer (Chrome), WIN405 Windon Mono Basin mixer (Matt Black), ARV405 Arvan Mono Basin mixer (Matt Black), WIN470 Windon High Rise mixer (Matt Black), ARV470 Arvan High Rise mixer (Matt Black), WIN805 Windon Mono Basin mixer (Brushed Brass), ARV805 Arvan Mono Basin mixer (Brushed Brass), WIN870 Windon High Rise mixer (Brushed Brass), ARV870 Arvan High Rise mixer (Brushed Brass), WIN505 Windon Mono Basin mixer (Polished Gunmetal), ARV505 Arvan Mono Basin mixer (Polished Gunmetal), WIN570 Windon High Rise mixer (Polished Gunmetal), ARV570 Arvan High Rise mixer (Polished Gunmetal), WIN705 Windon Mono Basin mixer (Brushed Gunmetal), ARV705 Arvan Mono Basin mixer (Brushed Gunmetal), WIN770 Windon High Rise mixer (Brushed Gunmetal), ARV770 Arvan High Rise mixer (Brushed Gunmetal).

Manufacturer:

Ultra Finishing Ltd.

Company Name

Ultra Finishing Ltd.

Address

Raikes Lane Industrial Estate, Bolton, Lancashire

Postcode

BL3 2NH

Phone

01282 436934

View All Listings by this Company

Single hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 65ºC.

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2204316

Expiry date:

30/04/2027

Size:

Stainless-steel braided TPSiV lined flexible hose assemblies incorporating ⅜” captive nut end connections.

Marking:

Herz logo on operating member. Manufacturer logo (Herz), manufacturer “letter” date code on body.

Installation Requirements:

R001 R006 R009 R010

Model:

Infinity I10

Manufacturer:

Herz d.o.o.

Company Name

Herz d.o.o.

Address

Grmaska Cesta 3 1275 Smartno pri Litiji

Country

Slovenia

Phone

+38 6 41 390 045

View All Listings by this Company

Single hole, single outlet (fixed) combination tap assemblies (brass body, various finishes - see model) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The product is supplied with a pop-up waste. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2205340

Expiry date:

31/05/2027

Note:

No testing performed on pop-up waste.

Size:

Stainless steel braided PEX lined flexible hose assemblies incorporating ½” captive nut end connections.

Marking:

Kohler on operating member.

Installation Requirements:

R001 R006 R009 R010

Model:

72275W-4-** Where ** denotes finish and can be replaced by: 2BZ - Oil Rubbed Bronze, BZ - Antique Bronze, SA - Antique Silver, 96 - Biscuit, 7 - Black, W7 - Black Nickel, LB - Bronze, G - Brushed Chrome, AG - Brushed Nickel, BS - Brushed Stainless, FGN - Chartreuse, FRD - Cherry Red, GN - Gunmetal, BL - Matte Black, YG - Matte Gold, FNY - Navy Blue, AD - Nickel Silver, R2B - Oil Rubbed Bronze-Gold, CP - Polished Chrome, 1CP - Polished Chrome, ABS PGD - Polished Gold, 24K - Polished Gold, S - Polished Stainless, AGP PVD - Brushed Nickel, 24P PVD - Polished Gold, ADP PVD - Silver Nickel, FBG - Retro Blue, RGD - Rose Gold, TB - Satin Black, SSL - Sterling Silver, TT - Titanium, ULB - Un-lacquered Brass, BV - Vibrant Brushed Bronze, BN - Vibrant Brushed Nickel, AF - Vibrant French Gold, BGD - Vibrant Modern Brushed Gold, PB - Vibrant Polished Brass, SN - Vibrant Polished Nickel, VS - Vibrant Stainless, VNT - Vintage Nickel, W6 - Weathered Bronze, 0 - White, 2MB - Modern Brass.

Manufacturer:

Kohler Mira Ltd.

Company Name

Kohler Mira Ltd.

Address

Cromwell Road, Cheltenham, Gloucestershire

Postcode

GL52 5EP

Country

United Kingdom

Phone

+44 (0) 844 571 5000

View All Listings by this Company

‘Grandera’ range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes, see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The 23.303 prefix models are supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2205344

Expiry date:

31/05/2027

Note:

No testing performed on pop-up waste.

Size:

Stainless steel braided PEX lined flexible hose assemblies incorporating ⅜” captive end connections.

Marking:

Grohe on operating member. New models have Grohe SPA on body

Installation Requirements:

R001 R006 R009 R010

Model:

Grandera range: 23.303.XXX, 23.310.XXX, 23.313.XXX. Where XXX denotes finish and can be replaced by: 000 - Chrome, DA0 - Warm Sunset (23.303 model only), IG0 - Chrome/Gold. New models added August 23 24.369 24.370 24.371

Factor:

Grohe AG

Company Name

Grohe AG

Address

Industriepark Edelburg 58675 Hemer

Country

Germany

Phone

02372 930

General Email

info@grohe.com

View All Listings by this Company

Single hole, single outlet fixed combination tap assembly (chrome plated brass), incorporating a sequential headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum operating pressure 10.0 bar. Maximum operating temperature 65°C.

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2206007

Expiry date:

30/06/2027

Size:

Stainless steel braided PEX lined flexible hose assemblies incorporating ½" captive nut end connections.

Marking:

LANBIAO on body

Installation Requirements:

R001 R006 R010

Model:

F5142

Manufacturer:

Taizhou Lanbiao Sanitary Ware Co., Ltd.

Company Name

Taizhou Lanbiao Sanitary Ware Co., Ltd.

Address

Xudou Industrial Zone, Qinggang, Yuhuan, Taizhou

Country

China

View All Listings by this Company

Range of single hole, single outlet fixed combination tap assemblies (chrome plated brass bodies), incorporating quarter turn ceramic disc headworks with lever operating members. The spout outlet incorporates a plastic flow straightener. Maximum operating pressure 10.0 bar. Maximum operating temperature 65°C.

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2206905

Expiry date:

30/06/2027

Note:

Products are supplied with lever operated pop-up waste not verified by test.

Size:

15mm copper inlet tails

Marking:

Bristan on indice

Installation Requirements:

R001 R006 R010

Model:

RS2 BAS C 225912

Factor:

Bristan Group Limited

Company Name

Bristan Group Limited

Address

Birch Coppice Business Park Pooley Hall Drive Dordon

Postcode

B78 1SG

Country

Tamworth

Phone

01827 254144

General Email

enquire@bristan.com

View All Listings by this Company

Single hole, single outlet fixed combination tap assemblies (chrome plated brass), incorporating quarter turn ceramic disc headworks with a cross-top operating members. The spout outlet incorporates a plastic flow straightener. Maximum operating pressure 10.0 bar. Maximum operating temperature 65°C

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2206906

Expiry date:

30/06/2027

Note:

Products are supplied with lever operated pop-up waste not verified by test.

Size:

15mm copper inlet tails

Marking:

Bristan on indice.

Installation Requirements:

R001 R006 R010

Model:

N BAS C CD 231810

Factor:

Bristan Group Limited

Company Name

Bristan Group Limited

Address

Birch Coppice Business Park Pooley Hall Drive Dordon

Postcode

B78 1SG

Country

Tamworth

Phone

01827 254144

General Email

enquire@bristan.com

View All Listings by this Company

Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The 32.825.00E and 32.883.000 models are supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2206306

Expiry date:

30/06/2027

Note:

No testing performed on pop-up waste.

Size:

Polyamide (PA) braided PEX lined flexible hose assemblies incorporating ⅜” captive nut end connections

Marking:

Grohe logo on operating member. Grohe and date of manufacture followed by 2 digit production location code (YYMM-52) on rear of tap.

Installation Requirements:

R001 R006 R009 R010

Model:

32.824.000 - Eurosmart Cosmopolitan basin mixer S-size, 32.825.00E - Eurosmart Cosmopolitan basin mixer S-size, 32.883.000 - GET basin mixer.

Factor:

Grohe AG

Company Name

Grohe AG

Address

Industriepark Edelburg 58675 Hemer

Country

Germany

Phone

02372 930

General Email

info@grohe.com

View All Listings by this Company

Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (chrome plated) incorporating ceramic cartridge headworks and single lever operating members. The spout outlet incorporates a plastic aerator. Some models are supplied with a click waste (see model list). Maximum working pressure 5.0 bar. Maximum operating temperature 60ºC.

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2206351

Expiry date:

30/06/2027

Size:

Stainless steel braided PEX lined flexible hose assemblies incorporating ½” captive nut end connections.

Marking:

Deva on operating member and DTC53 on rear of body (All models except WHINS2313) Methven on operating member and DTC53 on rear of body (model WHINS2313)

Installation Requirements:

R001 R006 R010

Model:

INS2313 Insignia Mini Basin Mixer. INS113 Insignia Basin Mono Mixer. HUD113 Hudson Basin Mixer With Press Top Waste. KAS113 Kasai Basin Mixer. MOS113 Mosselle Basin Mixer. WHINS2313 WH Insignia Mini Mono Basin with Press Top Waste. Model added October 2022: PAX113 Model added 17/03/2023 PABMCP Models added September 2023: IBK113 IBK313 KIEL113 VLN113 Models added February 2024: INS313 Model added March 2024: INS112

Factor:

Methven UK Limited

Company Name

Methven UK Limited

Address

3-3A Stone Cross Court, Yew Tree Way, Golborne, Warrington

Postcode

WA3 3JE

Country

United Kingdom

Phone

0800 195 1602

View All Listings by this Company

Single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a quarter turn ceramic disc headworks with cross top operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2107147

Expiry date:

31/07/2026

Size:

M10

Marking:

AOLIJIE & WRAS on rear of body.

Installation Requirements:

R001 R006 R010

Model:

Ceramic Disc, Cross Top: ALJ-50101 COMBINATION TAP ASSEMBLIES

Factor:

TAIZHOU AOLIJIE SANITARY WARE CO., LTD

Company Name

TAIZHOU AOLIJIE SANITARY WARE CO., LTD

Address

NO.27 JINBO ROAD SHAMEN YUHUAN TAIZHOU

Country

China

View All Listings by this Company

Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The cold water inlet incorporates an approved check valve cartridge, verified by test (as suitable for backflow protection against Fluid Category 2) The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2203339

Expiry date:

31/03/2027

Size:

Stainless-steel braided PEX lined flexible hose assemblies incorporating ½” captive nut end connections

Marking:

Lota on body

Installation Requirements:

R001 R006 R009 R010

Model:

63441-00X 63441-01X X denotes finish and can be replaced with: 01 - Chrome 04 - Brushed Nickel 4408 - Brushed Brass 6801 - Matt Black 08 - Stainless steel 5804 - Heirloom Silver 0402 - Brushed Nickel PVD

Manufacturer:

Xiamen Lota International Co., Ltd.

Company Name

Xiamen Lota International Co., Ltd.

Address

No.61 Xingnan Road, Jimei District, Xiamen, 361022

Country

China

Phone

86-592-6665866

View All Listings by this Company

Single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2207007

Expiry date:

31/07/2027

Size:

Stainless steel braided EPDM lined flexible hose assembly with ½” captive nuts

Marking:

LOTA on body of tap

Installation Requirements:

R001 R006 R009 R010

Model:

60147-5001

Manufacturer:

Xiamen Lota International Co., Ltd.

Company Name

Xiamen Lota International Co., Ltd.

Address

No.61 Xingnan Road, Jimei District, Xiamen, 361022

Country

China

Phone

86-592-6665866

View All Listings by this Company

Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The product is supplied with a click type waste. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2207035

Expiry date:

31/07/2027

Size:

Grey polymeric (PET - Polyethylene terephthalate) braided PEX lined flexible hose assemblies incorporating ½" captive nut end connections.

Marking:

PPI on rear of tap.

Installation Requirements:

R001 R006 R009 R010

Model:

204138, 204138EX.

Manufacturer:

PPI Xiamen Industry Co Ltd

Company Name

PPI Xiamen Industry Co Ltd

Address

No 88 South Houxiang Road Xinyang Industrial Zone Haicang District Xiamen 361022

Country

China

View All Listings by this Company

Single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates either a combined EPDM washer and stainless steel strainer with a plastic flow straightener, or an EPDM washer with a plastic aerator. The product is supplied with a click type waste, verified by test. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2207306

Expiry date:

31/07/2027

Size:

Stainless steel braided EPDM lined flexible hose assemblies with ½” captive nut end connections.

Marking:

PPI on rear of body.

Installation Requirements:

R001 R006 R010

Model:

194838

Manufacturer:

PPI Xiamen Industry Co Ltd

Company Name

PPI Xiamen Industry Co Ltd

Address

No 88 South Houxiang Road Xinyang Industrial Zone Haicang District Xiamen 361022

Country

China

View All Listings by this Company

Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The product is supplied with optional ⅜” BSP (M) x ½” BSP (F) adaptors each with two fibre gaskets for installation on each inlet hose. The spout outlet incorporates a plastic aerator. The 58005 model is supplied with a pop-up waste. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2207321

Expiry date:

31/07/2027

Note:

No testing performed on pop-up waste.

Size:

Stainless steel braided PEX lined flexible hose assemblies incorporating ⅜” captive nut end connections.

Marking:

Gessi on operating member.

Installation Requirements:

R001 R006 R009 R010

Model:

58005, 58006.

Manufacturer:

Gessi S.p.A.

Company Name

Gessi S.p.A.

Address

Parco Gessi - Fraz. Vintebbio 13037 Serravalle Sesia

Country

Italy

Phone

+39 0163 454111

View All Listings by this Company

Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The product is supplied with or without a pop-up waste or a retractable chain. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2207349

Expiry date:

31/07/2027

Note:

No testing performed on pop-up waste.

Size:

Stainless steel braided PEX lined flexible hose assemblies incorporating ⅜” captive nut end connections..

Marking:

Grohe on operating member.

Installation Requirements:

R001 R006 R009 R010

Model:

Eurodisc Cosmopolitan: 32.469.20E without pop-up waste, 33.178.20E with retractable chain, 33.190.20E with pop-up waste.

Factor:

Grohe AG

Company Name

Grohe AG

Address

Industriepark Edelburg 58675 Hemer

Country

Germany

Phone

02372 930

General Email

info@grohe.com

View All Listings by this Company

Single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straighter with a stainless steel strainer. The inlet hoses are also supplied with an additional a plastic flow limiter, copper washer and a brass nut. Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C.

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

1905099

Expiry date:

31/05/2024

Note:

No testing performed on pop-up waste

Size:

Stainless steel braided PEX lined flexible hose assemblies incorporating ½” captive nut end connections.

Marking:

AKW on body.

Installation Requirements:

R001 R006 R009 R010

Model:

12-011-080 COMBINATION TAP ASSEMBLIES

Factor:

DLP Limited

Company Name

DLP Limited

Address

Unit L, Snugborough, Bradden, Isle of Man

Postcode

IM4 4LH

Country

United Kingdom

View All Listings by this Company

Single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2207069

Expiry date:

31/07/2027

Size:

Stainless steel braided EPDM lined flexible hose assembly with ½” captive nuts

Marking:

AKW on body of tap

Installation Requirements:

R001 R006 R009 R010

Model:

08-008-04

Factor:

DLP Limited

Company Name

DLP Limited

Address

Unit L, Snugborough, Bradden, Isle of Man

Postcode

IM4 4LH

Country

United Kingdom

View All Listings by this Company

Range of single hole, single outlet (fixed) combination tap assemblies (brass body, various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The product can be supplied with a pop-up waste (see model). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2209002

Expiry date:

30/09/2027

Note:

No testing performed on pop-up waste.

Size:

Stainless steel braided thermoplastic silicone rubber (TPSiV) lined flexible hose assemblies incorporating ⅜” captive nut end connections.

Marking:

Hansgrohe on body.

Installation Requirements:

R001 R006 R009 R010

Model:

71 754 xxx 150 with pop-up waste, 71 755 xxx without waste set, 72 113 xxx with pop-up waste set, 72 115 xxx with pop-up waste set, 72 116 xxx without waste set. Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.

Factor:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Auestrasse 5 - 9, 77761 Schiltach

Country

Germany

View All Listings by this Company

Manufacturer:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Auestrasse 5 - 9, 77761 Schiltach

Country

Germany

View All Listings by this Company

Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies with various finishes, see model) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. Model TVW112001000 and TVW112002000 are supplied with pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2209306

Expiry date:

30/09/2027

Size:

Stainless-steel braided PEX lined flexible hose assemblies with 3/8” BSP captive nut end connections.

Marking:

Villeroy & Boch & 1748 on operating member.

Installation Requirements:

R001 R006 R009 R010

Model:

TVW112001000 Subway 3.0 Washbasin mixer w/waste Small, TVW112002000 Subway 3.0 Washbasin mixer w/waste Medium, TVW112003000 Subway 3.0 Washbasin mixer w/o waste Medium, TVW112004000 Subway 3.0 Washbasin mixer w/o waste Large. Model added December 2022: TVW112001001 Subway 3.0 Washbasin mixer w/o waste Small. Each model is manufactured in 4 different finishes: chrome-plated (suffix 61), black matt epoxy painted (suffix K5), PVD brushed gold (suffix 76) and Brushed nickel matt (suffix 64).

Factor:

Villeroy & Boch AG

Company Name

Villeroy & Boch AG

Address

Postfach 11 20 66688 Mettlach Germany

Country

Germany

View All Listings by this Company

Range of single hole, single outlet (fixed) combination tap assemblies incorporating a brass body and ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2209311

Expiry date:

30/09/2027

Note:

R009 does not apply to PEX hoses

Size:

Stainless-steel braided PEX lined flexible hose assemblies with ½” BSP captive nut end connections.

Marking:

Lanbiao on operating member

Installation Requirements:

R001 R006 R010

Model:

F9402 & F9402L Models added November 2022 F9402-H & F9402-GJS F9402L-H & F9402L-GJS Models added October 2023 F9402-QH F9402-DMGJL F9402L-QH F9402L-DMGJL

Manufacturer:

Taizhou Lanbiao Sanitary Ware Co., Ltd.

Company Name

Taizhou Lanbiao Sanitary Ware Co., Ltd.

Address

Xudou Industrial Zone, Qinggang, Yuhuan, Taizhou

Country

China

View All Listings by this Company

Range of single hole, single outlet fixed combination tap assemblies (chrome plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener. The product is supplied with an approved click-type waste. Maximum operating pressure 10.0 bar. Maximum operating temperature 60°C

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2212900

Expiry date:

31/12/2027

Size:

Stainless steel braided EPDM lined flexible hoses with ½” BSP (F) captive nut end connections.

Marking:

Bristan on the operating member

Installation Requirements:

R001 R006 R010

Model:

BQMEC BAS C & SM BAS C

Factor:

Bristan Group Limited

Company Name

Bristan Group Limited

Address

Birch Coppice Business Park Pooley Hall Drive Dordon

Postcode

B78 1SG

Country

Tamworth

Phone

01827 254144

General Email

enquire@bristan.com

View All Listings by this Company

Single-hole, single outlet, fixed combination tap assembly (chrome plated brass) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The product is supplied with an approved click-type waste. Maximum working pressure 10.0 Bar Maximum operating temperature 60°C.

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2212902

Expiry date:

31/12/2027

Size:

Stainless-steel braided EPDM lined flexible hose assemblies with ½” BSP (F) captive nut end connections.

Marking:

Bristan on operating member.

Installation Requirements:

R001 R006 R010

Model:

PS2 BAS C

Factor:

Bristan Group Limited

Company Name

Bristan Group Limited

Address

Birch Coppice Business Park Pooley Hall Drive Dordon

Postcode

B78 1SG

Country

Tamworth

Phone

01827 254144

General Email

enquire@bristan.com

View All Listings by this Company

Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The cold water inlet incorporates an approved check valve cartridge, verified by test (as suitable for backflow protection against Fluid Category 2) The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2203373

Expiry date:

31/03/2027

Size:

Stainless-steel braided PEX lined flexible hose assemblies incorporating ½” captive nut end connections

Marking:

Clearwater on body

Installation Requirements:

R001 R006 R009 R010

Model:

TAK10CP, TAK10BN, TAK10BB, TAK10MB, ALA30CP, ALA30BN, ALA30BB, ALA30MB & ALA30SS

Factor:

Clearwater Products Limited t/a Sterling

Company Name

Clearwater Products Limited t/a Sterling

Address

Shannon Place Tewkesbury Business Park Tewkesbury Gloucestershire

Postcode

GL20 8BB

Country

United Kingdom

Phone

0168429955

View All Listings by this Company

Range of single hole, single outlet (fixed) combination tap assemblies, brass bodies (various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Products are supplied with approved pop-up waste. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2210001

Expiry date:

31/01/2027

Size:

Stainless steel braided PEX lined flexible hose assemblies with ½” BSP captive nuts.

Marking:

LOTA on body.

Installation Requirements:

R001 R006 R009 R010

Model:

63553-70X 63555-70X X denotes the finish, and can be replaced with any of the following: 01 Chrome, 6801 Matt Black, 4408 Brushed Brass, 0402 Brushed Nickel PVD, 5804 Heirloom Silver, 08 Stainless steel, 04 Brushed Nickel.

Manufacturer:

Xiamen Lota International Co Ltd

Company Name

Xiamen Lota International Co Ltd

Address

No. 61 Xing Nan Road Jimei District Xiamen, 361022

Country

China

View All Listings by this Company

Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies) incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator and the products are supplied with lever operated pop up wastes. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2210044

Expiry date:

31/10/2027

Size:

Stainless-steel braided PEX lined flexible hose assemblies incorporating 3/8" BSP (F) captive nuts end conections

Marking:

Hansgrohe on operating member.

Installation Requirements:

R001 R006 R009 R010

Model:

71570xxx Vernis Blend 71571xxx Vernis Blend 71572xxx Vernis Blend

Factor:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Auestrasse 5 - 9, 77761 Schiltach

Country

Germany

View All Listings by this Company

Single hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating ceramic cartridge headwork with single lever operating member. The spout outlets incorporate a plastic aerator and the products are supplied with a click waste. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2210307

Expiry date:

31/10/2027

Size:

Stainless steel braided EPDM lined flexible inlet hose assemblies incorporating ½” BSP captive nut end connections.

Marking:

DTC32 on rear of body and DEVA on operating member.

Installation Requirements:

R001 R006 R010

Model:

HEN113 Henley & KGS113 Kingston.

Factor:

Methven UK Limited

Company Name

Methven UK Limited

Address

3-3A Stone Cross Court, Yew Tree Way, Golborne, Warrington

Postcode

WA3 3JE

Country

United Kingdom

Phone

0800 195 1602

View All Listings by this Company

Single hole, single outlet (fixed) combination tap assemblies (chrome plated brass body) incorporating a ceramic cartridge headwork with various operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2210326

Expiry date:

31/10/2027

Size:

Stainless steel braided, PEX lined flexible hose assembly incorporating ½” BSP (F) captive nut.

Marking:

Alfred Victoria and Heyang on operating member

Installation Requirements:

R001 R006 R009 R010

Model:

GA08, MG08, QA08, QJ08, QB08, QG08, AD08, QC08, WR08, AW08, FA08, MJ08, MC08, MK08, RP08, AP08, RS08, XA08, RA08, EV08, AE08, PV08, CB08, HN08, IB08, CG08, SG08, HC08, ZB08, RG08, AX08, TG08, HD08 & DP08

Manufacturer:

KAIPING HEYANG SANITARY WARE CO., LTD

Company Name

KAIPING HEYANG SANITARY WARE CO., LTD

Address

No.18 Tangliang Road, the Third Industrial Zone Shuikou Town, Kaiping City, Guangdong 529321

Country

China

View All Listings by this Company

Single hole, single outlet, fixed combination tap assembly (brass body in various finishes) incorporating ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2210331

Expiry date:

31/10/2027

Size:

Stainless steel braided, PEX lined hose assembly incorporating 3/8” BSP captive nut

Marking:

Villeroy & Boch, 1748 on operating member

Installation Requirements:

R001 R006 R009 R010

Model:

TVW112006000 Subway 3.0 This model is manufactured in 4 different finishes: chrome-plated (suffix 61), black matt epoxy painted (suffix K5), PVD brushed gold (suffix 76) and Brushed nickel matt (suffix 64).

Factor:

Villeroy & Boch AG

Company Name

Villeroy & Boch AG

Address

Postfach 11 20 66688 Mettlach Germany

Country

Germany

View All Listings by this Company

Single hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2210337

Expiry date:

31/10/2027

Size:

Nylon braided, PEX lined flexible hose assemblies incorporating 3/8” captive nut end connections.

Marking:

Grohe on operating member.

Installation Requirements:

R001 R006 R009 R010

Model:

23330001 BauEdge

Manufacturer:

Grohe AG

Company Name

Grohe AG

Address

Industriepark Edelburg 58675 Hemer

Country

Germany

Phone

02372 930

View All Listings by this Company

Range of single-hole, fixed combination tap assemblies (chrome plated brass), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlet incorporates plastic flow aerator. The product is supplied with a brass open outlet adaptor for the spout. Maximum working pressure 10.0 Bar Maximum operating temperature 60°C.

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.

WRAS Approval Number:

2210900

Expiry date:

31/10/2027

Size:

15MM copper tails

Marking:

Bristan on operating members.

Installation Requirements:

R001 R006 R010

Model:

SOLO-NM SL SOLO-NM LL SOLO-NMT LL

Factor:

Bristan Group Ltd.

Company Name

Bristan Group Ltd.

Address

Birch Coppice Business Park, Pooley Hall Drive, Dordon, Tamworth. Staffordshire

Postcode

B78 1SG.

Country

United Kingdom

Phone

0844 7016274

View All Listings by this Company