Range of floor-standing gas combination boilers, supplied with isolation valves, expansion vessel and a pressure relief valve set at 3.0 bar. Maximum working pressure: Primary circuit 2.5 bar, secondary 10 bar. Maximum operating temperature: Primary 82°C / secondary circuit 60°C.
Range of water meters with brass bodies. The inlet incorporates a plastic strainer. Maximum working pressure 16.0 bar. Maximum operating temperature is 50°C or 85°C, please refer to model.
Compact wall outlet elbow with brass body (various finishes). Maximum operating temperature 85.0°C Open outlet use only
Range of flow sensors incorporating either brass, plastic or stainless steel bodies & EPDM ‘O’-rings. Maximum working pressure 10.0 bar for models VVXA, VVXC, VVXB. Maximum working pressure 16.0 bar for models VVXD & VVXE. Maximum operating temperature 90°C.
Range of multistage centrifugal pumps with stainless-steel housings, stainless-steel impellers and EPDM ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted angled overhead showers, consisting of stainless-steel bodies (various finishes) and silicone nozzles. The inlets are fitted with plastic flow limiters. Maximum operating temperature 65⁰C. Open outlet use only.
Range of brass shower arms and plastic shower heads (various finishes) incorporating EPDM seals and ‘O’-rings, silicone seals and spray insert. The 26 469 xxx model is ceiling mounted & 26 470 xxx model is wall mounted. Maximum operating temperature 60°C. Open outlet use only.
In-line `Y`-patterned strainers with bronze bodies incorporating stainless steel mesh strainers and PTFE washers. Maximum working pressure 20.0 Bar Maximum operating temperature 85.0°C
Range of drain off taps incorporating DZR brass bodies and non-rising spindle operating mechanisms. Fig 370 range incorporates lock-shield mechanisms and the Fig 371 range incorporates key operated mechanisms. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C.
Range of draining taps, straight or elbowed with brass bodies incorporating a rising spindle headwork. Maximum working pressure 10.0 Bar Maximum operating temperature 95.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 902001 X XXX | VARIOUS | 1/2” BSP male inlet. | 10.0 bar | 85 °C | PPI | BODY | No | Non-rising spindle | Metal Backnuts | Flow Straightener | |
| 902002 X XXX | VARIOUS | 3/4” BSP male inlet. | 10.0 bar | 65 °C | PPI | BODY | No | Non-rising spindle | Metal Backnuts | Flow Straightener |
X XXX Denotes the following: First X: Different handle option and the second, third & fourth XXX for different finishes: Handles: F – Cross Top Type Chrome – No suffix, brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| R 1/2 C | Chrome | 1/2" BSP Male | 7.0 bar | 60 °C | Bristan | Indice | No | Non-rising spindle | Metal Backnuts | Flow Straightener | |
| R 3/4 C | Chrome | 3/4" BSP Male | 7.0 bar | 60 °C | Bristan | Indice | No | Non-rising spindle | Metal Backnuts | Flow Straightener |
Range of pillar taps, incorporating a non-rising spindle headwork with cross top or dome type operating members. The spout outlet incorporates a plastic flow straightener, and the product is supplied with metal back nuts. All taps will be supplied with an optional Flow Regulator. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 936L | Chrome | G3/4, male | 10 bar | 60 °C | WRAS, XINYA | BODY | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | |
| 932L | Chrome | G1/2, male | 10 bar | 60 °C | WRAS, XINYA | BODY | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator |
Range of wall or floor mounted, self-closing taps (brass or chromium plated brass) with spring loaded headworks and either dome type, foot pedal or stick operating members. Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C.
FLEXCORE range of stainless steel and polyamide braided flexible polyethylene lined hose assemblies with various end connections. For use with copper pipe to EN1057 Maximum working pressure:10 bar Maximum operating temperature:70°C
502 series of automatic air venting valves with brass bodies, plastic float and EPDM ‘O’-rings. For non-potable water use only. Maximum working pressure 10.0 bar. Maximum operating temperature see models.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 15 745 xx0 | Various | basic set (G3/4) | 10 bar | 70 °C | hansgrohe | on the escutcheon | Yes | Push button detent | |||
| 15 764 xx0 | Various | basic set (G3/4) | 10 bar | 70 °C | hansgrohe | on the escutcheon | Yes | Push button detent | |||
| 36 717 xx0 | Various | basic set (G3/4) | 10 bar | 70 °C | AXOR | on the escutcheon | Yes | Push button detent | |||
| 36 727 xx0 | Various | basic set (G3/4) | 10 bar | 70 °C | AXOR | on the escutcheon | Yes | Push button detent | |||
| 36 773 xx0 | Various | basic set (G3/4) | 10 bar | 70 °C | AXOR | on the escutcheon | Yes | Push button detent |
Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish
Wall mounted thermostatic bar, shower valve, incorporating a ceramic disc headwork controlling the flow with a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member which incorporates a manual override button. Each inlet incorporates a combined EPDM washer and stainless-steel strainer and an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is also supplied with a riser rail, shower hose and handset. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| VE SHXSMFF C | Chrome | 15mm compression | 5 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Shower Hose, Handset, Riser Rail, |
| RP3 CE SHXSMFF C | Chrome (Cr3) | 15mm compression | 5 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Shower Hose, Handset, Riser Rail, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| T43014B | Chromed | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| T43084B | Chromed | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| T43014T | Chromed | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| T43084T | Chromed | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| T43034 | Chromed | BSP 3/4" (M) x BSP 1/2" (M) offset unions | 10 bar | 85 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| T43064B | Chromed | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| T43194B | Chromed | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| T44014B | Chromed | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| T44054B | Chromed | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| T44014T | Chromed | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| T44054T | Chromed | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable |
Range of wall mounted, thermostatic shower valves (brass body – Chrome finish), incorporating a single sequential headwork controlling both temperature and flow using a single lever operating member. The inlets incorporate stainless-steel strainers, plastic flow regulators and approved check valve cartridges (verified by test - suitable for backflow protection against fluid category 2) Product is not supplied with shower hose, handset, overhead shower or riser rail assembly. Maximum working pressure 10.0 Bar Maximum operating temperature 60°C.
Range of wall mounted thermostatic shower valves with brass bodies (chromium plated) incorporating a ceramic disc controlling the flow to the shower (for some models it diverts the flow to a hand shower or overhead shower) using a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member incorporating a manual override button. Inlets incorporate stainless steel strainers and an approved single check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating pressure 5.0 bar. Maximum operating temperature 50°C
Range of butterfly valves incorporating blue or green epoxy coated ductile iron bodies, discs and EPDM seals. Maximum working pressure 16.0 Bar Maximum operating temperature 65.0°C
Combined pre-set temperature and pressure relief valves (set at 7.0 bar) incorporating DZR brass body. The compression connection to be used with copper pipe BS EN 1057. Maximum working pressure 7.0 bar. Maximum operating temperature 95°C.
Combined pre-set temperature and pressure relief valves (set at 7.0 bar) incorporating DZR brass body. The compression connection to be used with copper pipe BS EN 1057. Maximum working pressure 7.0 bar. Maximum operating temperature 95°C.
Range of in-line pilot operated level control valves with blue epoxy coated ductile iron bodies. The products have flow control facility controlled via a float operated valve and are supplied with auxiliary components including stainless steel pipe & fittings, spherical valves, bleed valve and a needle valve. Maximum working pressure 16.0 Bar. Maximum operating temperature 60.0°C.
Range of inline pilot operated altitude control valves with blue epoxy coated ductile iron bodies and bonnets. The pilot system consists of spherical valves, in line strainers, needle valve, non-return valve, altitude gauge and a pre-set altitude control valve. The spring rating of the pilot 10-60ft (3 to 18m). Maximum working pressure 16.0 Bar Maximum operating temperature 60.0°C
Range of pilot operated pressure relief control valves with blue epoxy coated ductile iron bodies and supplied with auxiliary components including stainless steel pipe & fittings, spherical valves, bleed valve and a needle valve. Spring ratings of pilot valve are 0.35 - 3.5 bar, 0.7 - 5.5bar, 1.38 - 13.8 bar, 6.9 - 20.7 bar Maximum working pressure 16.0 Bar Maximum operating temperature 60.0°C
Range of press fit spherical valves with brass and chrome plated brass bodies. For use with copper pipe to BS EN 1057. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of inline or angled screwdriver and lever operated isolation and servicing valves (See models), (chrome plated brass bodies) and ball, incorporating EPDM ‘O’-rings. For use with copper pipe manufactured to EN1057 Maximum working pressure: 10 bar. Maximum working temperature: 99°C.
Range of spherical valves with bronze bodies (brushed chrome plated), brass ball and PTFE seals. Incorporating a lever type operating member. Maximum working pressure 25.0 Bar Maximum operating temperature 85.0°C
Range of spherical valves with nickel plated brass bodies and a chrome plated ball. The handle can either be a flat lever handle or a T handle (See models) Maximum working pressure 25.0, 30.0, 40.0, 50.0 Bar Maximum operating temperature 60.0°C
Range of inline brass bodied or chrome plated brass bodied spherical valves, with a chrome plated brass ball and EPDM ‘O’-rings. SVB66MB and SV44MB models are lever operated. SV66MBC and SVT64MBC are screwdriver operated. The products are for use with PE-X pipe (manufactured to BS 7291-3), PB pipe (manufactured to BS 7291-2) and copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Cold water use only. From March 2026: Maximum operating temperature 65°C.
Range of PVC-U double union ball valves incorporating EPDM O-rings. Maximum working pressure 16.0 Bar. Cold water use only
Range of gate valves with blue epoxy coated ductile iron bodies, EPDM coated ductile iron wedge and EPDM seals. Valves are operated via a non-rising spindle headwork. Maximum working pressure 16.0 Bar Maximum operating temperature 100.0°C
Range of gate valves with blue epoxy ductile iron bodies, ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
AMEXSA range of resilient seated gate valves with blue epoxy coated ductile iron bodies and bonnets and ductile iron wedges encapsulated in EPDM. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of gate valves incorporating either rising or non-rising spindle headworks and PTFE gaskets and Bronze body, bronze wedge and handwheel. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of blue or green polyethylene coated ductile iron gate valves incorporating an EPDM Wedge. The valves operate via a non-rising spindle headwork with hand wheel operating member. Maximum working pressure 16.0 Bar Maximum operating temperature 65.0°C
Range of handwheel operated bronze bodied stop valves. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of push-fit, screw down stop valves with plastic bodies for use with copper pipe (manufactured to EN1057), PEX pipe (manufactured to BS 7291-3) and/or MDPE pipe (manufactured to EN 12201 (inserts required). For above and below ground use. Maximum working pressure:16.0 bar Maximum operating temperature: 20.0°C.
Range of inline plastic bodied screw down stop valves incorporating a non-rising spindle headwork with a dome type operating member. The products are for use with PE-X pipe (manufactured to BS 7291-3) and copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Cold water use only. From March 2026: Maximum operating temperature 65°C.
Range of inlet control valves with DZR brass bodies. The valves consist of an adjustable pressure reducing valve set at 3.0 bar, pressure relief valve set at either 4.5, 6.0 or 8.0 bar. The valves also incorporate an approved check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). For use with copper pipe to BS EN 1057. Maximum working pressure 16.0 Bar. Maximum operating temperature 65°C.
Range of double regulating valves available with bronze bodies. Products incorporate a non-rising spindle headwork. Products also include two test ports. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
'TENAC-C 4590'. White (translucent) coloured, injection moulded acetal material. For use with water up to 85°C.
'Ak99,5 - 99,5% Alumina Ceramic'. Ivory coloured, compression moulded and fired Ceramic material. For use with water up to 85°C.
'LM119-1'. Factory applied, white coloured epoxy coating. Apply as per manufacturer's User Instructions 'File no.: LM-001', 'Edition: A', 'Issue date: 2024-JAN.-15th'. Cure for 10 minutes@190°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘BSS R/G System’. Grey coloured, factory applied, two-component epoxy coating comprising of ‘BSS Red and BSS Grey’. ‘BSS Red’ comprises of a base and curing agent which are mixed in a 3:1 volume ratio. ‘BSS Grey’ comprises of a base and curing agent which are mixed in a 3:1 volume ratio. Apply as per manufacturer's Product Data Sheet ‘BSS-D0003’, dated ‘2025-09-16’. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Nitocote EP 405’. Site applied, two-part,white coloured epoxy based Waterproofing coating. Mix 3.1 litres of the base with 0.9 litres of hardener and apply as per manufacturer’s TDS ‘UAE/0228/22/K’. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 76 of 89
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
