Range of concealed and exposed thermostatic shower valves available in different finishes and flow rates. Shower valves supplied with overhead shower and handset. Concealed shower valves available as either wall mounted or ceiling mounted. The inlet connections incorporate single check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of thermostatic shower panels incorporating a single sequential thermostatic control valve with a single lever operating member and flexible riser kit. Each inlet supplied with a servicing valve, EPDM o-ring and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Products are supplied with black lined PVC shower hoses and chrome plated shower handsets. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Wall mounted thermostatic bar shower mixer (matte black plated brass), incorporating a ceramic disc diverter headwork controlling the flow between shower handset and overhead shower with a dome type operating member and a thermostatic cartridge controlling the temperature with a dome type operating member that incorporates a manual override button. The inlets incorporate stainless-steel EPDM strainer washers and approved check valve cartridges; (however, the complete product has not been fully tested to demonstrate it provides backflow protection). The product is supplied with screwdriver operated isolation valves, an overhead shower incorporating an EPDM washer at the inlet, shower handset, shower hose incorporating an EPDM washer at the captive nut and a stainless-steel EPDM strainer washer in the conical nut & riser rail assembly. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted thermostatic blending valves (various finishes) incorporating a quarter turn ceramic disc headworks with single lever type operating members. The temperature is controlled independently via a thermostatic cartridge with manual override and single lever type operating members. The inlets incorporate stainless-steel EPDM strainer washers and approved single check valve cartridges (however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection). The products are supplied with shower hose, shower handset and riser rail assembly. Maximum operating pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies and discs, incorporating EPDM seats. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies and discs, incorporating EPDM seats. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of butterfly valves with blue epoxy coated ductile iron bodies with stainless steel and an EPDM seat. Sizes DN50-DN150 are lever operated. Sizes DN200-300 are gearbox operated. Maximum working pressure 25.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies and discs. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gear or lever operated wafer, semi lugged butterfly valves with blue epoxy coated ductile iron bodies, stainless steel discs and EPDM seats. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 80°C
Range of high and low pressure diaphragm float operated valves with brass body and backnuts. Maximum working pressure 8.0 or 10.0 bar (please refer to model). Cold water use only.
Range of piston type float operated inlet valves with brass bodies and backnuts. Maximum working pressure 8.0 or 10.0 bar (please refer to model). Cold water use only.
Range of swing gate, non-return valves with blue epoxy coated ductile iron bodies, carbon steel swing gate encapsulated in EPDM and EPDM valve seats. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of pilot operated, adjustable, pressure reducing control valves with blue epoxy coated ductile iron bodies. The valves are supplied with a pilot valve, three spherical valves and a needle valve. Maximum supply pressure 16.0 bar. Outlet pressure setting is adjustable in the range of 2.0 – 12.0 bar. Maximum operating temperature 80°C. Above ground use only.
Range of pre-set pressure relief valves (set at 3.0 bar) with plastic bodies and EPDM diaphragm. Maximum working pressure 3.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of ‘IBall Vortex’ flow through valves with brass body and EPDM ‘O’-rings incorporating a plastic spherical valve and a drain tap. Maximum working pressure: 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of spherical valves with nickel plated brass bodies, chromium plated brass balls, PTFE seals, NBR and/or FKM ‘O’-rings. incorporates a stainless-steel strainer. Also incorporate a magnet. Maximum working pressure: See PN in brackets under model. Maximum operating temperature: Cold water use only.
Range of spherical valves with brass bodies and chrome plated brass ball, PTFE washer and EPDM `O` ring and various operating methods. Maximum working pressure 10.0 or 40 bar (see model).
Non-metallic materials and components comply with BS6920 at 85°C
Range of spherical valves with a single lever or ‘T’ handle operating member. The products have a DZR brass body and a chrome plated DZR brass ball, except for the models with the ‘-OT’ suffix, models have (nickel-plated brass bodies) and chrome plated brass ball. The products are supplied with various end connections (see model). Maximum working pressures: 15mm to 28mm = 40 Bar 35mm = 25 bar 42mm to 54mm = 16 bar (All models). 42 to 54mm = 10 Bar (4E05, 4E05-OT, 4E06 and 4E06-OT models) Maximum operating temperature 40.0°C
Range of quarter turn, lever handle or butterfly operated spherical valves with nickel plated brass bodies, chrome plated brass balls and PTFE seals. For use with copper pipe BS EN 1057. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of lever operated spherical valves with bronze bodies, PTFE seals and chromium plated brass ball. Maximum working pressure 20.0 bar. Maximum operating temperature 99°C.
Range of gate valves with a non-rising spindle with a handwheel operating member or lockshield connection. All models have brass or DZR brass body and brass wedge. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
AVK Series 21 range of gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM, EPDM ‘O’-rings and non-rising spindles. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 50°C
Range of gate valves incorporating ductile iron epoxy coted bodies and with EPDM ‘O’-ring seals and discs. The valves are operated via a non-rising spindle with a hand wheel operating member Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated ductile iron bodies, non-rising spindles with handwheel operating member and a ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 bar. Cold water use only. From Jan 2025 maximum operating temperature 50°C, for models marked "WRAS - 50 DEGREES" on adhesive label on bonnet.
Electrolytic scale inhibitors with nickel plated copper bodies, for use with copper pipe manufactured to BS EN 1057. Maximum working pressure 12.0 bar. Cold water use only.
'Corro Coat EP-F 5001'. Factory applied, blue coloured fusion bonded epoxy coating. Apply as per manufacturer's technical data sheet dated '24 September 2021'. Cure for 2.5 minutes@232°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Pentaline 1000 Red & Pentaline 1000 Grey'. Factory applied, red and grey coloured, two component solventless epoxy coatings. Mix component A & B in a volume ratio of 3:1 and apply as per manufacturer's document number 'Chembur R&D/PI/05', issue date '03/04/2023'. Cure for 7 days@30°C. 'Pentaline 1000 Red' is for use with water up to 45°C. 'Pentaline 1000 Grey' is for use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'WB50 Black Waterborne Pipe Anticorrosive Paint'. Factory applied, black coloured polyacrylate coating. Apply as per manufacturer's instructions '005', revision date '2021.12.12' . Cure for 24 hours@23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'WEP50 Black Waterborne Epoxy Pipe Anticorrosive Paint'. Factory applied, black coloured epoxy coating. Apply as per manufacturer's instructions '005', revision date '2021.12.12' . Cure for 24 hours@23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'3011 Red Epoxy Anticorrosive Coating'. Factory applied, red coloured epoxy coating. Apply as per manufacturer's instructions '004', revision date '2021.12.12' . Cure for 24 hours@23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'5015 Blue Epoxy Anticorrosive Coating'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's instructions '005', revision date '2021.12.12' . Cure for 24 hours@23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘E1H8691 ValveClad, E1H8868 ValveClad & E2H6531’. Factory applied, blue coloured epoxy powder coatings (manufactured in UK and France). Apply as per manufacturer’s instructions dated January 2023. Cure for 10 minutes@180°C (metal temperature). E1H8691 ValveClad and E1H8868 ValveClad are for use with water up to 23°C. E2H6531 is for use with water up to 70°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'5013 Blue Waterborne Pipe Anti-Corrosive Paint'. Factory applied, blue coloured polyacrylate paint. Apply as per manufacturer's TDS/IFU '001', 'First Edition', dated '2021.12.12'. Cure for 24 hours@23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NP-TANK 500 PW'. Factory applied, white coloured (once mixed), two-component, solvent-free epoxy coating. Mix Part A (white liquid) with Part B (dark amber liquid) in a 3:1 volume ratio. Apply as per manufacturer's TDS 'Rev. 06/22'. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'AMMT-029 Waterborne Anticorrosive Coating'. Factory applied, black coloured acrylic modified resin coating. Apply as per manufacturer's Instructions for Users 'version 2.00', updated '11/01/2021'. Cure for 7 days@23°C. For use with water up to 40°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Xypex Concentrate'. Site applied, grey coloured, cementitious coating. Mix 'Xypex Concentrate' with water in a 5:2 ratio and apply as per manufacturer's datasheet 'DAT-CON-UK, REV-06-21'. Cure for 3 days@7°C in damp conditions, following by 18 days@7°C. Please note that 1 day cure = 24 hours. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CPT CML Variation No.2 cementitious mortar’ for use with ‘Conplast RP264 Admixture'. Site applied, grey coloured (once mixed) cementitious mortar and admixture. 'CPT CML Variation No.2 cementitious mortar’ comprises of cement, sand and Microsilica. Mix cement and sand dry in a 1:1.1 mass ratio. Add the microsilica in a 1:0.05 mass ratio with the cement content. Add water in a cement/water mass ratio of 1:0.32. Add the admixture in an admixture/ cement ratio of 8ml:1000g. Mix rigorously until an even consistency is achieved and apply as per manufacturer’s instructions reference ‘2328’, dated 13/01/2023. Cure for 28 days@ between 10°C and 35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Carlow Tank Mix 1'. Factory prepared, grey coloured concrete mix. Mix and apply as per statement from ‘Carlow Concrete Tanks', dated '23rd January 2023' Cure for 7 days@21°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Aquastore'. Grey coloured, GRP panels manufactured by hydraulic press. For use with water up to 60°C.
'Aquasystem'. Grey coloured, GRP panels manufactured by hydraulic press. For use with water up to 60°C.
'Aquatank'. Grey coloured, GRP panels manufactured by hydraulic press. For use with water up to 60°C.
'CPP-GRE12' & 'CPP-GRE951' Pipes. Yellow/green (translucent) coloured GRE pipes manufactured using a two-step process which involves hand lay-up and then filament winding. For use with water up to 70°C.
'Atlac 430'. Yellow coloured, vinyl ester resin material manufactured by filament winding. For use with water up to 60°C.
'SL6015 Silicone Hose'. White coloured (translucent), extruded silicone hose. Shore hardness 60. Tested in-radius size 0.5mm. For use with water up to 85°C.
'SABFUSE'. Black coloured, injection moulded polyethylene fittings. For use with water up to 60°C.
'National Brand PE Pipe'. Blue coloured, extruded PE100 pipe. For use with water up to 65°C.
'EPPI-PE'. Black coloured, extruded HDPE pipe. For use with water up to 60°C.
'UPIPIPE'. Black coloured, extruded HDPE pipe. For use with water up to 60°C.
'SABIC® Vestolen A RELY 5922R 10000'. Black coloured, compression moulded HDPE material. For use with water up to 23°C.
'SABIC® Vestolen A 5061R 10000'. Black coloured, compression moulded HDPE material. For use with water up to 23°C.
Page 69 of 236
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
